Re: [PATCH v3] ramips: mt7621: Add Arcadyan WE420223-99 support
On 1/2/23 17:36, Harm Berntsen wrote: The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access point distributed as Experia WiFi by KPN in the Netherlands. It features two ethernet ports and 2 internal antennas. Specifications -- SOC : Mediatek MT7621AT ETH : Two 1 gigabit ports, built into the SOC WIFI : MT7615DN BUTTON: Reset BUTTON: WPS LED : Power (green+red) LED : WiFi (green+blue) LED : WPS (green+red) LED : Followme (green+red) Power : 12 VDC, 1A barrel plug Winbond variant: RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM Flash : Winbond W25Q256JVFQ, 256Mb SPI U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1 Macronix variant: RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM Flash : MX25l25635FMI-10G, 256Mb SPI U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1 Serial -- The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin header. The pinout is: VCC (the square), RX, TX, GND. Installation See the Wiki page [1] for more details, it comes down to: 1. Open the device, take off the heat sink 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also connect the RESET pin for stability (thanks @FPSUsername for reporting) 3. Make a backup in case you want to revert to stock later 4. Flash the squashfs-factory.trx file to offset 0x5 of the flash 5. Ensure the bootpartition variable is set to 0 in the U-Boot environment located at 0x3 Note that the U-Boot is password protected, this can optionally be removed. See the forum [2] for more details. MAC Addresses(stock) +--+--+---+ | use | address | example | +--+--+---+ | Device | label| 00:00:00:11:00:00 | | Ethernet | + 3 | 00:00:00:11:00:03 | | 2g | + 0x02f1 | 02:00:00:01:00:01 | | 5g | + 1 | 00:00:00:11:00:01 | +--+--+---+ The label address is stored in ASCII in the board_data partition Notes - - This device has a dual-boot partition scheme, but OpenWRT will claim both partitions for more storage space. Known issues - 2g MAC address does not match stock due to missing support for that in macaddr_add - Only the power LED is configured by default References -- [1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99 [2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653 Signed-off-by: Harm Berntsen --- package/boot/uboot-envtools/files/ramips | 3 + .../dts/mt7621_arcadyan_we420223-99.dts | 219 ++ target/linux/ramips/image/mt7621.mk | 25 ++ .../mt7621/base-files/etc/board.d/02_network | 8 + .../etc/hotplug.d/ieee80211/10_fix_wifi_mac | 9 + .../mt7621/base-files/lib/upgrade/platform.sh | 1 + 6 files changed, 265 insertions(+) create mode 100644 target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts diff --git a/package/boot/uboot-envtools/files/ramips b/package/boot/uboot-envtools/files/ramips index 372b8a49e2..9dbe2cb181 100644 --- a/package/boot/uboot-envtools/files/ramips +++ b/package/boot/uboot-envtools/files/ramips @@ -17,6 +17,9 @@ alfa-network,awusfree1|\ alfa-network,quad-e4g|\ alfa-network,r36m-e4g|\ alfa-network,tube-e4g|\ +arcadyan,we420223-99) + ubootenv_add_uci_config "/dev/mtd2" "0x0" "0x1000" "0x1000" + ;; This changes the ubootenv_add_uci_config also for the alfa-network devices I think this is not intended. Please move your new entry after the "ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x1000"" line. engenius,esr600h|\ sitecom,wlr-4100-v1-002) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x1000" ___ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
Re: [PATCH v3] ramips: mt7621: Add Arcadyan WE420223-99 support
On 2.01.2023 19:36, Harm Berntsen wrote: The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access point distributed as Experia WiFi by KPN in the Netherlands. It features two ethernet ports and 2 internal antennas. Specifications -- SOC : Mediatek MT7621AT ETH : Two 1 gigabit ports, built into the SOC WIFI : MT7615DN BUTTON: Reset BUTTON: WPS LED : Power (green+red) LED : WiFi (green+blue) LED : WPS (green+red) LED : Followme (green+red) Power : 12 VDC, 1A barrel plug Winbond variant: RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM Flash : Winbond W25Q256JVFQ, 256Mb SPI U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1 Macronix variant: RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM Flash : MX25l25635FMI-10G, 256Mb SPI U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1 Serial -- The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin header. The pinout is: VCC (the square), RX, TX, GND. Installation See the Wiki page [1] for more details, it comes down to: 1. Open the device, take off the heat sink 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also connect the RESET pin for stability (thanks @FPSUsername for reporting) 3. Make a backup in case you want to revert to stock later 4. Flash the squashfs-factory.trx file to offset 0x5 of the flash 5. Ensure the bootpartition variable is set to 0 in the U-Boot environment located at 0x3 Note that the U-Boot is password protected, this can optionally be removed. See the forum [2] for more details. MAC Addresses(stock) +--+--+---+ | use | address | example | +--+--+---+ | Device | label| 00:00:00:11:00:00 | | Ethernet | + 3 | 00:00:00:11:00:03 | | 2g | + 0x02f1 | 02:00:00:01:00:01 | | 5g | + 1 | 00:00:00:11:00:01 | +--+--+---+ The label address is stored in ASCII in the board_data partition Notes - - This device has a dual-boot partition scheme, but OpenWRT will claim both partitions for more storage space. Known issues - 2g MAC address does not match stock due to missing support for that in macaddr_add - Only the power LED is configured by default References -- [1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99 [2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653 Signed-off-by: Harm Berntsen Acked-by: Arınç ÜNAL Arınç ___ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
[PATCH v3] ramips: mt7621: Add Arcadyan WE420223-99 support
The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header. To mitigate this problem, the original message has been wrapped automatically by the mailing list software.--- Begin Message --- The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access point distributed as Experia WiFi by KPN in the Netherlands. It features two ethernet ports and 2 internal antennas. Specifications -- SOC : Mediatek MT7621AT ETH : Two 1 gigabit ports, built into the SOC WIFI : MT7615DN BUTTON: Reset BUTTON: WPS LED : Power (green+red) LED : WiFi (green+blue) LED : WPS (green+red) LED : Followme (green+red) Power : 12 VDC, 1A barrel plug Winbond variant: RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM Flash : Winbond W25Q256JVFQ, 256Mb SPI U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1 Macronix variant: RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM Flash : MX25l25635FMI-10G, 256Mb SPI U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1 Serial -- The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin header. The pinout is: VCC (the square), RX, TX, GND. Installation See the Wiki page [1] for more details, it comes down to: 1. Open the device, take off the heat sink 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also connect the RESET pin for stability (thanks @FPSUsername for reporting) 3. Make a backup in case you want to revert to stock later 4. Flash the squashfs-factory.trx file to offset 0x5 of the flash 5. Ensure the bootpartition variable is set to 0 in the U-Boot environment located at 0x3 Note that the U-Boot is password protected, this can optionally be removed. See the forum [2] for more details. MAC Addresses(stock) +--+--+---+ | use | address | example | +--+--+---+ | Device | label| 00:00:00:11:00:00 | | Ethernet | + 3 | 00:00:00:11:00:03 | | 2g | + 0x02f1 | 02:00:00:01:00:01 | | 5g | + 1 | 00:00:00:11:00:01 | +--+--+---+ The label address is stored in ASCII in the board_data partition Notes - - This device has a dual-boot partition scheme, but OpenWRT will claim both partitions for more storage space. Known issues - 2g MAC address does not match stock due to missing support for that in macaddr_add - Only the power LED is configured by default References -- [1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99 [2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653 Signed-off-by: Harm Berntsen --- package/boot/uboot-envtools/files/ramips | 3 + .../dts/mt7621_arcadyan_we420223-99.dts | 219 ++ target/linux/ramips/image/mt7621.mk | 25 ++ .../mt7621/base-files/etc/board.d/02_network | 8 + .../etc/hotplug.d/ieee80211/10_fix_wifi_mac | 9 + .../mt7621/base-files/lib/upgrade/platform.sh | 1 + 6 files changed, 265 insertions(+) create mode 100644 target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts diff --git a/package/boot/uboot-envtools/files/ramips b/package/boot/uboot-envtools/files/ramips index 372b8a49e2..9dbe2cb181 100644 --- a/package/boot/uboot-envtools/files/ramips +++ b/package/boot/uboot-envtools/files/ramips @@ -17,6 +17,9 @@ alfa-network,awusfree1|\ alfa-network,quad-e4g|\ alfa-network,r36m-e4g|\ alfa-network,tube-e4g|\ +arcadyan,we420223-99) + ubootenv_add_uci_config "/dev/mtd2" "0x0" "0x1000" "0x1000" + ;; engenius,esr600h|\ sitecom,wlr-4100-v1-002) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x1000" diff --git a/target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts b/target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts new file mode 100644 index 00..99de770707 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts @@ -0,0 +1,219 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include +#include + +/ { + model = "Arcadyan WE420223-99"; + compatible = "arcadyan,we420223-99", "mediatek,mt7621-soc"; + + aliases { + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_wps_green; + led-wifi = &led_wifi_green; + }; + + chosen { + bootargs = "console=ttyS0,57600 ubi.mtd=5 root=/dev/ubiblock0_0"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; +