[time-nuts] HP 10811-60165 Double Oven Crystal Oscillator Pin-Outs
I've seen a pin-out for the outer-oven 6-position connector (2 heater wires, 2 thermistor wires), but I've not found anything on the pin-out of the other 6-position connector. Has anyone come across the pin-outs for the 10811-60165 connectors? CS ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
Re: [time-nuts] HP 10811-60165 Double Oven Crystal Oscillator Pin-Outs
Chris, The 10811-60165 may be similar to the HP 10811-60158 that uses using the following pin-out: 1 - BRN Oscillator Return (Com) 2 - RED Oscillator Power (+12V) 3 - ORG Oven Monitor Return (Com) 4 - YEL Oven Monitor Output 5 - GRN Oven Power (+18-24V) 6 - BLU Oven Return (Com) The following description is from the 10811 A/B Manual where the recommended oven monitor circuit is shown: The Oven Monitor Output is an indicator of oven warm-up. At initial turn-on (warmup) the oven monitor will go to approximately 1.5 volts below the oven power supply voltage. After the oven cuts back, the output will drop to approximately 3.5 volts (at 25°C). The output impedance of this circuit is 10,000 ohms. Richard I've seen a pin-out for the outer-oven 6-position connector (2 heater wires, 2 thermistor wires), but I've not found anything on the pin-out of the other 6-position connector. Has anyone come across the pin-outs for the 10811-60165 connectors? CS ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
Re: [time-nuts] HP 10811-60165 Double Oven Crystal Oscillator Pin-Outs
That pin-out sounds promising as this unit has BLK-RED-BLK-ORG-YEL-GRN-BLU, which seems consistent with the one that you provided. Did you source that from one of HP's various guides or somewhere else? CS -Original Message- From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com]On Behalf Of Richard H McCorkle Sent: Tuesday, February 18, 2014 11:07 AM To: Discussion of precise time and frequency measurement Subject: Re: [time-nuts] HP 10811-60165 Double Oven Crystal Oscillator Pin-Outs Chris, The 10811-60165 may be similar to the HP 10811-60158 that uses using the following pin-out: 1 - BRN Oscillator Return (Com) 2 - RED Oscillator Power (+12V) 3 - ORG Oven Monitor Return (Com) 4 - YEL Oven Monitor Output 5 - GRN Oven Power (+18-24V) 6 - BLU Oven Return (Com) The following description is from the 10811 A/B Manual where the recommended oven monitor circuit is shown: The Oven Monitor Output is an indicator of oven warm-up. At initial turn-on (warmup) the oven monitor will go to approximately 1.5 volts below the oven power supply voltage. After the oven cuts back, the output will drop to approximately 3.5 volts (at 25°C). The output impedance of this circuit is 10,000 ohms. Richard I've seen a pin-out for the outer-oven 6-position connector (2 heater wires, 2 thermistor wires), but I've not found anything on the pin-out of the other 6-position connector. Has anyone come across the pin-outs for the 10811-60165 connectors? CS ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
Re: [time-nuts] HP 10811-60165 Double Oven Crystal Oscillator Pin-Outs
Chris, I bought a number of 10811-60158 so I determined the pin-out from an actual unit. Richard That pin-out sounds promising as this unit has BLK-RED-BLK-ORG-YEL-GRN-BLU, which seems consistent with the one that you provided. Did you source that from one of HP's various guides or somewhere else? CS -Original Message- From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com]On Behalf Of Richard H McCorkle Sent: Tuesday, February 18, 2014 11:07 AM To: Discussion of precise time and frequency measurement Subject: Re: [time-nuts] HP 10811-60165 Double Oven Crystal Oscillator Pin-Outs Chris, The 10811-60165 may be similar to the HP 10811-60158 that uses using the following pin-out: 1 - BRN Oscillator Return (Com) 2 - RED Oscillator Power (+12V) 3 - ORG Oven Monitor Return (Com) 4 - YEL Oven Monitor Output 5 - GRN Oven Power (+18-24V) 6 - BLU Oven Return (Com) The following description is from the 10811 A/B Manual where the recommended oven monitor circuit is shown: The Oven Monitor Output is an indicator of oven warm-up. At initial turn-on (warmup) the oven monitor will go to approximately 1.5 volts below the oven power supply voltage. After the oven cuts back, the output will drop to approximately 3.5 volts (at 25°C). The output impedance of this circuit is 10,000 ohms. Richard I've seen a pin-out for the outer-oven 6-position connector (2 heater wires, 2 thermistor wires), but I've not found anything on the pin-out of the other 6-position connector. Has anyone come across the pin-outs for the 10811-60165 connectors? CS ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
