Hi, Regarding recent topic, Spiderbeam mast suggestions needed. Please note, The September 2013 issue of Radio Society of Great Britain (RSGB) RADCOM contains an article by Steve Nichols G0KYA on the Spiderbeam Model 160-18-4 WTH 160M Vertical. Info on setting up, quality, and some idea on performance.
73 Phil G4LWB ======================================== Message Received: Aug 24 2013, 05:01 PM From: topband-requ...@contesting.com To: topband@contesting.com Cc: Subject: Topband Digest, Vol 128, Issue 25 Send Topband mailing list submissions to topband@contesting.com To subscribe or unsubscribe via the World Wide Web, visit http://lists.contesting.com/mailman/listinfo/topband or, via email, send a message with subject or body 'help' to topband-requ...@contesting.com You can reach the person managing the list at topband-ow...@contesting.com When replying, please edit your Subject line so it is more specific than "Re: Contents of Topband digest..." Today's Topics: 1. Spiderbeam mast suggestions needed (Jim Garland) 2. Vertical Antennas (Eddy Swynar) 3. Re: Spiderbeam mast suggestions needed (GeorgeWallner) ---------------------------------------------------------------------- Message: 1 Date: Fri, 23 Aug 2013 10:46:43 -0600 From: "Jim Garland" <4cx2...@miamioh.edu> To: Subject: Topband: Spiderbeam mast suggestions needed Message-ID: <002101cea020$5a04ba60$0e0e2f20$@miamioh.edu> Content-Type: text/plain; charset="us-ascii" Hi everyone, I'm _finally_ trying to erect a decent vertical for 80m and 160m, and have purchased a 26m (85ft) Spiderbeam mast. I'd really like to hear from guys who have used this mast for these bands. I'll have about 60 120ft radials. I've seen sheet from the manufacturer about using the mast as a monoband 160m shortened vertical. The diagram shows a wire wound aound the mast, with 4 7m wires near the top for a capacity hat, but wonder what other configurations people have used? Also, if possible I'd like to be able to use the mast on both 80m and 160m. It will located about 600 ft from my house. 73, Jim W8ZR ------------------------------ Message: 2 Date: Fri, 23 Aug 2013 13:00:11 -0400 From: Eddy Swynar To: topband@contesting.com Subject: Topband: Vertical Antennas Message-ID: <278fd2d7-c0de-4f58-a303-88b8bb9d7...@xplornet.ca> Content-Type: text/plain; charset=us-ascii Hi Guys, While I most certainly agree with what others such as Tom (W8JI) might offer here as to the value of TRUE "A" vs. "B" comparisons when it comes to how effective an antenna may be, I won't let a little thing like expediency deter me from erecting---and using---a "...less than stellar" antenna... Case in point: at our summer cottage (a two storey affair, with an upper balcony), I lashed together some aluminum tubing to tie to the railing on the second floor with bungy cord: I made up the balance of its length for a 1/4-wave 7-MHz vertical with a re-cycled old electrical extension cord dropped down from the aluminum, which terminates at the feed point some 3' above physical ground. I then unrolled 2 insulated counterpoise wires, 1/4-wavelength long, in opposite directions. Surprisingly the doggone thing works very well into Europe, no doubt testament as to the effectiveness of the stations of our European friends(!) as much as anything else at this end of my QSOs...but the point is, it works quite well with just the 100-watts that I might pump into it from my now-ancient Yaesu FT-980 transceiver. So don't despair, and---as the Nike slogan so aptly puts it---JUST DO IT!!! ~73~ de Eddy VE3CUI - VE3XZ ------------------------------ Message: 3 Date: Fri, 23 Aug 2013 16:19:59 -0400 From: "GeorgeWallner" To: "Jim Garland" <4cx2...@miamioh.edu>, Subject: Re: Topband: Spiderbeam mast suggestions needed Message-ID: Content-Type: text/plain;charset=utf-8; format="flowed" Jim, My home QTH and all my DXpeditions had SpiderPole verticals for 80 and 160 (and other bands). You have a wide range of options. A lot depends on how much work you are willing to do and how much efficiency you want to squeeze out of the system. The simplest arrangement would be a low loss loading coil (around 60 uH) somewhere in the middle to resonate the antenna on 1.9 MHz. Use AWG #14 insulated wire for the whole length and fold it back at the tip to create a 30 cm (1 foot) diameter loop to reduce voltages on the tip and to add a little bit of top loading. Add an approximately 8 uH inductor between the base and GND. You will find a 50 ohm tap point on the inductor somewhere around the center. For the base inductor use 1/4 inch copper pipe or large diameter wire. For 80 m use a relay to switch in a suitable L matching network. An alternative is to use an inverted L configuration. Use very thin wire for the horizontal section to reduce the side load as the tope part of the SpiderPole is very flexible. You may find that you can get decent SWR with the 50 ohm coax connected directly to the feed-point. (That would indicate a high ground system impedance and substantial losses, but...) Otherwise use a simple L network to match the coax to the feed-point. One word of caution, an inverted L that is resonant on 160 will have a very high reactive feed-point impedance on 80 and will also have a high radiation angle. You can use a shorter horizontal wire (around 8 meters) and two switchable matching networks, one for 80 and one for 160 m. An alternative to consider is to leave off the top two sections of the 26 m SpiderPole to create a stiffer pole which can hold more side load. The horizontal wire would have to be correspondingly longer but the improvement in mechanical strength would be well worth the slightly lower efficiency. For something a lot more elaborate (and something that can cover all bands, check out the antenna used on VK9GMW. (http://vk9gmw.com/documents/VK9GMW_ANTENNA.pdf ) That antenna worked great because of the salt water, but with enough radials you could get good performance on land too. For a permanent installation I strongly recommend that you paint the antenna once you got it working. Use flexible urethane paint. It will make it last 5 times longer. You should also have at least 3 guy ropes, attached somewhere around the middle. For ultimate strength, buy two poles and insert one inside the other. The antenna at my QTH has an 11 m tall 100 mm diameter aluminum tube with two 18 m SpiderPoles on top, for a total height of 29 m. No guy ropes. It works from 160 to 30 m via a tuner and has been up since 2009. (You can see a picture of this antenna on my QRZ.com page.) GL and 73, George, AA7JV On Fri, 23 Aug 2013 10:46:43 -0600 "Jim Garland" <4cx2...@miamioh.edu> wrote: > Hi everyone, > > I'm _finally_ trying to erect a decent vertical for 80m >and 160m, and have > purchased a 26m (85ft) Spiderbeam mast. I'd really like >to hear from guys > who have used this mast for these bands. I'll have about >60 120ft radials. > I've seen sheet from the manufacturer about using the >mast as a monoband > 160m shortened vertical. The diagram shows a wire wound >aound the mast, with > 4 7m wires near the top for a capacity hat, but wonder >what other > configurations people have used? Also, if possible I'd >like to be able to > use the mast on both 80m and 160m. It will located about >600 ft from my > house. > > 73, > > Jim W8ZR > > _________________ > Topband Reflector ------------------------------ Subject: Digest Footer _______________________________________________ Topband mailing list Topband@contesting.com http://lists.contesting.com/mailman/listinfo/topband ------------------------------ End of Topband Digest, Vol 128, Issue 25 **************************************** _________________ Topband Reflector