[U-Boot] Where can i get this patch ??
Hi All, Can any of you please let me know where can I get this patch. [U-Boot] [PATCH] Marvell 88E Switch/PHY init support Also why is this not yet part of main release ?? Thanks, Ravi___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] [U-Boot-Users] U-boot for PPC405GP based custom Board
Hi Feng, Below is the screen dump after enabling Debug. .. === Booting RFL GARD 8000 Controller using u-boot based bootloader === U-Boot 1.3.0-rc4 (Jun 24 2010 - 16:47:32) CPU: AMCC PowerPC 405GP Rev. E at 200 MHz (PLB=100, OPB=50, EBC=50 MHz) , PCI sync clock at 50 MHz 16 kB I-Cache 8 kB D-Cache Board: RFL-GARD8000 with AMCC PPC405GP processor I2C: ready DRAM: 64 MB SDRAM test passes FLASH: FLASH ADDR: fc00 FLASH MANUFACT: 10001 FLASH DEVICEID: 227e227e C2: LS: 22012201 info->flash_id: f2 Size of Flash0 at addr 0xfc00 is 0x200 FLASH ADDR: FLASH MANUFACT: ## Unknown FLASH on Bank 1 - Size = 0x = 0 MB Size of Flash1 at addr 0x0 is 0x0 32 MB *** Warning - bad CRC, using default environment In:serial Out: serial Err: serial Error: start and/or end address not on sector boundary Error: start and/or end address not on sector boundary Error: start and/or end address not on sector boundary Hit any key to stop autoboot: 0 => flinfo Bank # 1: AMD S29GL256N (256 Mbit, uniform sector size) Size: 32768 KB in 256 Sectors Sector Start Addresses: FC00 FC02 FC04 FC06 FC08 FC0A FC0C FC0E FC10 FC12 FC14 FC16 FC18 FC1A FC1C FC1E FC20 FC22 FC24 FC26 FC28 FC2A FC2C FC2E FC30 FC32 FC34 FC36 FC38 FC3A FC3C FC3E FC40 FC42 FC44 FC46 FC48 FC4A FC4C FC4E FC50 FC52 FC54 FC56 FC58 FC5A FC5C FC5E FC60 FC62 FC64 FC66 FC68 FC6A FC6C FC6E FC70 FC72 FC74 FC76 FC78 FC7A FC7C FC7E FC80 FC82 FC84 FC86 FC88 FC8A FC8C FC8E FC90 FC92 FC94 FC96 FC98 FC9A FC9C FC9E FCA0 FCA2 FCA4 FCA6 FCA8 FCAA EFCAC FCAE EFCB0 FCB2 E FCB4 FCB6 EFCB8 FCBA EFCBC FCBE EFCC0 FCC2 EFCC4 FCC6 E FCC8 FCCA EFCCC FCCE EFCD0 FCD2 EFCD4 FCD6 EFCD8 FCDA FCDC FCDE EFCE0 FCE2 EFCE4 FCE6 EFCE8 FCEA EFCEC FCEE E FCF0 FCF2 EFCF4 FCF6 EFCF8 FCFA EFCFC FCFE EFD00 FD02 E FD04 FD06 FD08 FD0A EFD0C FD0E EFD10 FD12 EFD14 FD16 E FD18 FD1A EFD1C FD1E EFD20 FD22 EFD24 FD26 EFD28 FD2A E FD2C FD2E EFD30 FD32 EFD34 FD36 EFD38 FD3A FD3C FD3E E FD40 FD42 EFD44 FD46 EFD48 FD4A EFD4C FD4E EFD50 FD52 E FD54 FD56 EFD58 FD5A EFD5C FD5E EFD60 FD62 EFD64 FD66 FD68 FD6A EFD6C FD6E EFD70 FD72 EFD74 FD76 EFD78 FD7A E FD7C FD7E FD80 FD82 EFD84 FD86 EFD88 FD8A EFD8C FD8E E FD90 FD92 EFD94 FD96 EFD98 FD9A EFD9C FD9E EFDA0 FDA2 E FDA4 FDA6 EFDA8 FDAA FDAC FDAE EFDB0 FDB2 EFDB4 FDB6 E FDB8 FDBA EFDBC FDBE EFDC0 FDC2 EFDC4 FDC6 EFDC8 FDCA FDCC FDCE FDD0 FDD2 EFDD4 FDD6 EFDD8 FDDA EFDDC FDDE E FDE0 FDE2 EFDE4 FDE6 EFDE8 FDEA EFDEC FDEE FDF0 FDF2 E FDF4 FDF6 EFDF8 FDFA EFDFC FDFE E => Thanks, Ravishankar Govindarao RFL Electronics Inc. E-mail : ravi@rflelect.com Voice: 973.334.3100 Ext. 233 Fax: 973.334.3863 CONFIDENTIALITY NOTE This e-mail, including any
Re: [U-Boot] [U-Boot-Users] U-boot for PPC405GP based custom Board
Hi Feng, We do not have two banks. Our design has only one Bank but two chips in the single Bank. Any idea how to get this working in u-boot.. Thanks Ravishankar Govindarao RFL Electronics Inc. E-mail : ravi@rflelect.com Voice: 973.334.3100 Ext. 233 Fax: 973.334.3863 CONFIDENTIALITY NOTE This e-mail, including any attachments, may contain confidential and/or legally privileged information. The Information is intended only for the use of the individual or entity named on this e-mail . If you are not the intended recipient, you are hereby notified that any disclosure, copying, distribution, or the taking of any action in reliance on the contents of this transmitted Information is strictly prohibited. Further, if you are not the intended recipient, please notify us by return e-mail and delete the Information promptly. Feng Kan 06/24/2010 05:45 PM To ravi@rflelect.com cc u-boot@lists.denx.de Subject Re: [U-Boot-Users] U-boot for PPC405GP based custom Board I dont know how the hardware is tied down. But at it seems to be getting bank 0 correctly. However, you second bank base address should be bank0_base + size instead of 0. You may have a hardware problem. Feng Kan On Thu, Jun 24, 2010 at 2:14 PM, wrote: Hi Feng, Below is the screen dump after enabling Debug. .. === Booting RFL GARD 8000 Controller using u-boot based bootloader === U-Boot 1.3.0-rc4 (Jun 24 2010 - 16:47:32) CPU: AMCC PowerPC 405GP Rev. E at 200 MHz (PLB=100, OPB=50, EBC=50 MHz) , PCI sync clock at 50 MHz 16 kB I-Cache 8 kB D-Cache Board: RFL-GARD8000 with AMCC PPC405GP processor I2C: ready DRAM: 64 MB SDRAM test passes FLASH: FLASH ADDR: fc00 FLASH MANUFACT: 10001 FLASH DEVICEID: 227e227e C2: LS: 22012201 info->flash_id: f2 Size of Flash0 at addr 0xfc00 is 0x200 FLASH ADDR: FLASH MANUFACT: ## Unknown FLASH on Bank 1 - Size = 0x = 0 MB Size of Flash1 at addr 0x0 is 0x0 32 MB *** Warning - bad CRC, using default environment In:serial Out: serial Err: serial Error: start and/or end address not on sector boundary Error: start and/or end address not on sector boundary Error: start and/or end address not on sector boundary Hit any key to stop autoboot: 0 => flinfo Bank # 1: AMD S29GL256N (256 Mbit, uniform sector size) Size: 32768 KB in 256 Sectors Sector Start Addresses: FC00 FC02 FC04 FC06 FC08 FC0A FC0C FC0E FC10 FC12 FC14 FC16 FC18 FC1A FC1C FC1E FC20 FC22 FC24 FC26 FC28 FC2A FC2C FC2E FC30 FC32 FC34 FC36 FC38 FC3A FC3C FC3E FC40 FC42 FC44 FC46 FC48 FC4A FC4C FC4E FC50 FC52 FC54 FC56 FC58 FC5A FC5C FC5E FC60 FC62 FC64 FC66 FC68 FC6A FC6C FC6E FC70 FC72 FC74 FC76 FC78 FC7A FC7C FC7E FC80 FC82 FC84 FC86 FC88 FC8A FC8C FC8E FC90 FC92 FC94 FC96 FC98 FC9A FC9C FC9E FCA0 FCA2 FCA4 FCA6 FCA8 FCAA EFCAC FCAE EFCB0 FCB2 E FCB4 FCB6 EFCB8 FCBA EFCBC FCBE EFCC0 FCC2 EFCC4 FCC6 E FCC8 FCCA EFCCC FCCE EFCD0 FCD2 EFCD4 FCD6 EFCD8 FCDA FCDC FCDE EFCE0 FCE2 EFCE4 FCE6 EFCE8 FCEA EFCEC FCEE E FCF0 FCF2 EFCF4 FCF6 EFCF8 FCFA EFCFC FCFE EFD00 FD02 E FD04 FD06 FD08 FD0A EFD0C FD0E EFD10 FD12 EFD14 FD16 E FD18 FD1A EFD1C FD1E EFD20 FD22 EFD24 FD26 EFD28 FD2A E FD2C FD2E EFD30 FD32 EFD34 FD36 EFD38 FD3A FD3C FD3E E FD40 FD42 EFD44 FD46 EFD48 FD4A EFD4C FD4E EFD50 FD52 E FD54 FD56 EFD58
[U-Boot] U-boot for PPC405GP based custom Board
Hi All, I am reposting without any confidentiality crap. Appreciate any help to resolve this. Thanks, Ravi ravi rao/RFL/SLI 06/24/2010 05:14 PM To Feng Kan cc u-boot@lists.denx.de Subject Re: [U-Boot-Users] U-boot for PPC405GP based custom Board Hi Feng, Below is the screen dump after enabling Debug. .. === Booting RFL GARD 8000 Controller using u-boot based bootloader === U-Boot 1.3.0-rc4 (Jun 24 2010 - 16:47:32) CPU: AMCC PowerPC 405GP Rev. E at 200 MHz (PLB=100, OPB=50, EBC=50 MHz) , PCI sync clock at 50 MHz 16 kB I-Cache 8 kB D-Cache Board: RFL-GARD8000 with AMCC PPC405GP processor I2C: ready DRAM: 64 MB SDRAM test passes FLASH: FLASH ADDR: fc00 FLASH MANUFACT: 10001 FLASH DEVICEID: 227e227e C2: LS: 22012201 info->flash_id: f2 Size of Flash0 at addr 0xfc00 is 0x200 FLASH ADDR: FLASH MANUFACT: ## Unknown FLASH on Bank 1 - Size = 0x = 0 MB Size of Flash1 at addr 0x0 is 0x0 32 MB *** Warning - bad CRC, using default environment In:serial Out: serial Err: serial Error: start and/or end address not on sector boundary Error: start and/or end address not on sector boundary Error: start and/or end address not on sector boundary Hit any key to stop autoboot: 0 => flinfo Bank # 1: AMD S29GL256N (256 Mbit, uniform sector size) Size: 32768 KB in 256 Sectors Sector Start Addresses: FC00 FC02 FC04 FC06 FC08 FC0A FC0C FC0E FC10 FC12 FC14 FC16 FC18 FC1A FC1C FC1E FC20 FC22 FC24 FC26 FC28 FC2A FC2C FC2E FC30 FC32 FC34 FC36 FC38 FC3A FC3C FC3E FC40 FC42 FC44 FC46 FC48 FC4A FC4C FC4E FC50 FC52 FC54 FC56 FC58 FC5A FC5C FC5E FC60 FC62 FC64 FC66 FC68 FC6A FC6C FC6E FC70 FC72 FC74 FC76 FC78 FC7A FC7C FC7E FC80 FC82 FC84 FC86 FC88 FC8A FC8C FC8E FC90 FC92 FC94 FC96 FC98 FC9A FC9C FC9E FCA0 FCA2 FCA4 FCA6 FCA8 FCAA EFCAC FCAE EFCB0 FCB2 E FCB4 FCB6 EFCB8 FCBA EFCBC FCBE EFCC0 FCC2 EFCC4 FCC6 E FCC8 FCCA EFCCC FCCE EFCD0 FCD2 EFCD4 FCD6 EFCD8 FCDA FCDC FCDE EFCE0 FCE2 EFCE4 FCE6 EFCE8 FCEA EFCEC FCEE E FCF0 FCF2 EFCF4 FCF6 EFCF8 FCFA EFCFC FCFE EFD00 FD02 E FD04 FD06 FD08 FD0A EFD0C FD0E EFD10 FD12 EFD14 FD16 E FD18 FD1A EFD1C FD1E EFD20 FD22 EFD24 FD26 EFD28 FD2A E FD2C FD2E EFD30 FD32 EFD34 FD36 EFD38 FD3A FD3C FD3E E FD40 FD42 EFD44 FD46 EFD48 FD4A EFD4C FD4E EFD50 FD52 E FD54 FD56 EFD58 FD5A EFD5C FD5E EFD60 FD62 EFD64 FD66 FD68 FD6A EFD6C FD6E EFD70 FD72 EFD74 FD76 EFD78 FD7A E FD7C FD7E FD80 FD82 EFD84 FD86 EFD88 FD8A EFD8C FD8E E FD90 FD92 EFD94 FD96 EFD98 FD9A EFD9C FD9E EFDA0 FDA2 E FDA4 FDA6 EFDA8 FDAA FDAC FDAE EFDB0 FDB2 EFDB4 FDB6 E FDB8 FDBA EFDBC FDBE EFDC0 FDC2 EFDC4 FDC6 EFDC8 FDCA FDCC FDCE FDD0 FDD2 EFDD4 FDD6 EFDD8 FDDA EFDDC FDDE E FDE0 FDE2 EFDE4 FDE6 EFDE8 FDEA EFDEC FDEE FDF0 FDF2
Re: [U-Boot] U-boot for PPC405GP based custom Board
Hi, Looks like the syntax for .lds file has changed. It does not like any defines. I was trying to get the new syntax in .lds files to include file or define a constan but could not get a definitive answere. Any help is appreciated. By the way I have my own file for the custom board. Since the standard one also exhibited the problem I choose to send the error from taihu board. Thanks in advance, Ravishankar Govindarao RFL Electronics Inc. E-mail : ravi@rflelect.com Voice: 973.334.3100 Ext. 233 Fax: 973.334.3863 CONFIDENTIALITY NOTE This e-mail, including any attachments, may contain confidential and/or legally privileged information. The Information is intended only for the use of the individual or entity named on this e-mail . If you are not the intended recipient, you are hereby notified that any disclosure, copying, distribution, or the taking of any action in reliance on the contents of this transmitted Information is strictly prohibited. Further, if you are not the intended recipient, please notify us by return e-mail and delete the Information promptly. Wolfgang Denk 06/27/2010 05:18 PM To ravi@rflelect.com cc u-boot@lists.denx.de Subject Re: [U-Boot] U-boot for PPC405GP based custom Board Dear ravi@rflelect.com, please post U-Boot related questions always on the U-Boot mailing list. In message you wrote: > >Thanks for the help. I deleted the flash.c and enabled the standard CFI > and it seems to have fixed my problem. As per your suggestion I downloaded > the latest current version of U-boot ( > u-boot-2010.06-rc3) and Iam getting the following error during > compilation. > > /opt/timesys/toolchains/ppc4xx-linux/bin/ppc4xx-linux-gcc -E -g -Os > -mrelocatable -fPIC -meabi -D__KERNEL__ -DTEXT_BASE=0xFFFC > -I/mnt/homesA/ravi/g8k_26kernel/u-boot-2010.06-rc3/include -fno-builtin > -ffreestanding -nostdinc -isystem > /opt/timesys/toolchains/lib/gcc/powerpc-timesys-linux-gnu/4.2.1/include > -pipe -DCONFIG_PPC -D__powerpc__ -DCONFIG_4xx -ffixed-r2 -mstring > -msoft-float -Wa,-m405 -mcpu=405 -include > /mnt/homesA/ravi/g8k_26kernel/u-boot-2010.06-rc3/include/u-boot/u-boot.lds.h > -ansi -D__ASSEMBLY__ -P - > >u-boot.lds > UNDEF_SYM=`/opt/timesys/toolchains/ppc4xx-linux/bin/ppc4xx-linux-objdump > -x board/amcc/taihu/libtaihu.a lib/libgeneric.a lib/lzma/liblzma.a You should not use the Taihu board consifuration, but instead create your own. ... > /opt/timesys/toolchains/bin/powerpc-timesys-linux-gnu-ld:/mnt/homesA/ravi/g8k_26kernel/u-boot-2010.06-rc3/arch/powerpc/cpu/ppc4xx/u-boot.lds:23: > ignoring invalid character `#' in expression > /opt/timesys/toolchains/bin/powerpc-timesys-linux-gnu-ld:/mnt/homesA/ravi/g8k_26kernel/u-boot-2010.06-rc3/arch/powerpc/cpu/ppc4xx/u-boot.lds:23: > syntax error > Can you please tell me what I am missing ?? This should not happen. Either your tool chain is broken, or there was some problem with your download. Is there any chance that a Windows system was involved, so you have corrupted line endings (\r\n instead of plain \n) ? Best regards, Wolfgang Denk -- Humans do claim a great deal for that particular emotion (love). -- Spock, "The Lights of Zetar", stardate 5725.6 ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] U-boot for PPC405GP based custom Board
Sending the same message without confidentiality crap... ravi rao/RFL/SLI 06/28/2010 09:48 AM To Wolfgang Denk cc u-boot@lists.denx.de Subject Re: [U-Boot] U-boot for PPC405GP based custom Board Hi, Looks like the syntax for .lds file has changed. It does not like any defines. I was trying to get the new syntax in .lds files to include file or define a constan but could not get a definitive answere. Any help is appreciated. By the way I have my own file for the custom board. Since the standard one also exhibited the problem I choose to send the error from taihu board. Thanks in advance, Ravishankar Govindarao RFL Electronics Inc. E-mail : ravi@rflelect.com Voice: 973.334.3100 Ext. 233 Fax: 973.334.3863 Wolfgang Denk 06/27/2010 05:18 PM To ravi@rflelect.com cc u-boot@lists.denx.de Subject Re: [U-Boot] U-boot for PPC405GP based custom Board Dear ravi@rflelect.com, please post U-Boot related questions always on the U-Boot mailing list. In message you wrote: > >Thanks for the help. I deleted the flash.c and enabled the standard CFI > and it seems to have fixed my problem. As per your suggestion I downloaded > the latest current version of U-boot ( > u-boot-2010.06-rc3) and Iam getting the following error during > compilation. > > /opt/timesys/toolchains/ppc4xx-linux/bin/ppc4xx-linux-gcc -E -g -Os > -mrelocatable -fPIC -meabi -D__KERNEL__ -DTEXT_BASE=0xFFFC > -I/mnt/homesA/ravi/g8k_26kernel/u-boot-2010.06-rc3/include -fno-builtin > -ffreestanding -nostdinc -isystem > /opt/timesys/toolchains/lib/gcc/powerpc-timesys-linux-gnu/4.2.1/include > -pipe -DCONFIG_PPC -D__powerpc__ -DCONFIG_4xx -ffixed-r2 -mstring > -msoft-float -Wa,-m405 -mcpu=405 -include > /mnt/homesA/ravi/g8k_26kernel/u-boot-2010.06-rc3/include/u-boot/u-boot.lds.h > -ansi -D__ASSEMBLY__ -P - > >u-boot.lds > UNDEF_SYM=`/opt/timesys/toolchains/ppc4xx-linux/bin/ppc4xx-linux-objdump > -x board/amcc/taihu/libtaihu.a lib/libgeneric.a lib/lzma/liblzma.a You should not use the Taihu board consifuration, but instead create your own. ... > /opt/timesys/toolchains/bin/powerpc-timesys-linux-gnu-ld:/mnt/homesA/ravi/g8k_26kernel/u-boot-2010.06-rc3/arch/powerpc/cpu/ppc4xx/u-boot.lds:23: > ignoring invalid character `#' in expression > /opt/timesys/toolchains/bin/powerpc-timesys-linux-gnu-ld:/mnt/homesA/ravi/g8k_26kernel/u-boot-2010.06-rc3/arch/powerpc/cpu/ppc4xx/u-boot.lds:23: > syntax error > Can you please tell me what I am missing ?? This should not happen. Either your tool chain is broken, or there was some problem with your download. Is there any chance that a Windows system was involved, so you have corrupted line endings (\r\n instead of plain \n) ? Best regards, Wolfgang Denk -- Humans do claim a great deal for that particular emotion (love). -- Spock, "The Lights of Zetar", stardate 5725.6 ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
