Re: [U-Boot] MPC8641D stucks before relocation
You said you used the exactly same register for CodeWarrior and U-boot. CodeWarrior works but U-boot doesn't? You can try two methods to debug. 1) Build a RAMBOOT u-boot, use CodeWarrior to initialize DDR and copy u-boot to its destination and start to run. 2) Let u-boot initialize DDR, make a inf loop. Use CodeWarrior to attach to it and stop the core, check registers and memory access. York On 11/09/2013 01:51 AM, Ashish wrote: On Monday 28 October 2013 05:31 PM, Ashish Khetan wrote: I disabled the 2nd core by using cfg_core1_enable and D2_MSRCID1 signal is not connected and we are using DDR controller 2... will this create any obstacles to relocate? Is there any other register configuration for DDR? can somebody help me to understand this or give me some pointer to get more understanding for this... I am getting frusted because I am stuck at this point from last 20 days. please help... thanks in advance and Regards On Sat, Oct 26, 2013 at 12:20 AM, Ashish Khetan curieux.khe...@gmail.com mailto:curieux.khe...@gmail.com wrote: Thanks For reply, i check DDR configuration using Code warrior, and successfully getting read/write from DDR. I use the following configuration in code warrior and same in u-boot... writemem.l 0xf8006000 0x001f # CS0_BNDS writemem.l 0xf8006080 0x80914102 # CS0_CONFIG writemem.l0xf8006100 0x0007 # TIMING_CFG_3 writemem.l0xf8006104 0xFF770F0F # TIMING_CFG_0 writemem.l0xf8006108 0x7F78F777 # TIMING_CFG_1 writemem.l0xf800610C 0x00205114 # TIMING_CFG_2 writemem.l0xf8006110 0x43088008 # DDR_SDRAM_CFG writemem.l0xf8006114 0x24401000 # DDR_SDRAM_CFG2 writemem.l0xf8006118 0x43800E52 # DDR_SDRAM_MODE writemem.l0xf800611C 0x8000C000 # DDR_SDRAM_MODE_2 writemem.l0xf8006120 0x # DDR_SDRAM_MD_CNTL writemem.l0xf8006124 0x0508 # DDR_SDRAM_INTERVAL writemem.l0xf8006128 0x # DDR_DATA_INIT writemem.l0xf8006130 0x0380 # DDR_SDRAM_CLK_CNTL sleep 200 writemem.l0xf8006110 0xC3088008 # DDR_SDRAM_CFG but I did not understand... can you give some light on this. thanks again... On Fri, Oct 25, 2013 at 10:25 PM, York Sun york...@freescale.com mailto:york...@freescale.com wrote: It is probably because your DDR wasn't initialized correctly. You can try to dump all DDR registers and check if anyone is suspicious. You can also override any register before enabling the controller. You may also add some memory test before relocation. York On 10/25/2013 06:38 AM, Ashish Khetan wrote: hii I am using MPC8641D based custom board for evaluation purpose. I am using minimal configuration for this board i.e. only FLASH and DDR initialisation. when I compiled U-boot in debug mode its printing addresses, i check for those addresses and found that it is unable to relocate itself to DDR(4*MT47H64M16). The following message was printed... U-Boot 2013.04 (Oct 25 2013 - 15:05:33) Unicore software on multiprocessor system!! To enable mutlticore build define CONFIG_MP CPU: 8641, Version: 2.1, (0x80900021) Core: E600 Core 0 (MSSCR0=8000, PORDEVSR=ab08307), Version: 2.2, (0x80040202) Clock Configuration: CPU:800 MHz, MPX:400 MHz DDR:200 MHz (400 MT/s data rate), LBC:25 MHz L1:D-cache 32 KB enabled I-cache 32 KB enabled L2:Disabled Board: Wind River SBC8641D DRAM: DDR: 512 MiB Top of RAM usable for U-Boot at: 2000 Reserving 114k for U-Boot at: 1ffe3000 Reserving 136k for malloc() at: 1ffc1000 Reserving 80 Bytes for Board Info at: 1ffc0fb0 Reserving 152 Bytes for Global Data at: 1ffc0f18 Stack Pointer at: 1ffc0f00 New Stack Pointer is: 1ffc0f00 and stuck here... Any pointer or link to get more about this will be helpful. Thanks in Advance ___ U-Boot mailing list U-Boot@lists.denx.de mailto:U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot Now its working... by default the data width of bus was 64bit and ddr2 was configured for 32-bit.. so i change the data width and now its working... Thanks a lot for lighting up the path... now i
Re: [U-Boot] MPC8641D stucks before relocation
On Monday 28 October 2013 05:31 PM, Ashish Khetan wrote: I disabled the 2nd core by using cfg_core1_enable and D2_MSRCID1 signal is not connected and we are using DDR controller 2... will this create any obstacles to relocate? Is there any other register configuration for DDR? can somebody help me to understand this or give me some pointer to get more understanding for this... I am getting frusted because I am stuck at this point from last 20 days. please help... thanks in advance and Regards On Sat, Oct 26, 2013 at 12:20 AM, Ashish Khetan curieux.khe...@gmail.com mailto:curieux.khe...@gmail.com wrote: Thanks For reply, i check DDR configuration using Code warrior, and successfully getting read/write from DDR. I use the following configuration in code warrior and same in u-boot... writemem.l 0xf8006000 0x001f # CS0_BNDS writemem.l 0xf8006080 0x80914102 # CS0_CONFIG writemem.l 0xf8006100 0x0007 # TIMING_CFG_3 writemem.l 0xf8006104 0xFF770F0F # TIMING_CFG_0 writemem.l 0xf8006108 0x7F78F777 # TIMING_CFG_1 writemem.l 0xf800610C 0x00205114 # TIMING_CFG_2 writemem.l 0xf8006110 0x43088008 # DDR_SDRAM_CFG writemem.l 0xf8006114 0x24401000 # DDR_SDRAM_CFG2 writemem.l 0xf8006118 0x43800E52 # DDR_SDRAM_MODE writemem.l 0xf800611C 0x8000C000 # DDR_SDRAM_MODE_2 writemem.l 0xf8006120 0x # DDR_SDRAM_MD_CNTL writemem.l 0xf8006124 0x0508 # DDR_SDRAM_INTERVAL writemem.l 0xf8006128 0x # DDR_DATA_INIT writemem.l 0xf8006130 0x0380 # DDR_SDRAM_CLK_CNTL sleep 200 writemem.l 0xf8006110 0xC3088008 # DDR_SDRAM_CFG but I did not understand... can you give some light on this. thanks again... On Fri, Oct 25, 2013 at 10:25 PM, York Sun york...@freescale.com mailto:york...@freescale.com wrote: It is probably because your DDR wasn't initialized correctly. You can try to dump all DDR registers and check if anyone is suspicious. You can also override any register before enabling the controller. You may also add some memory test before relocation. York On 10/25/2013 06:38 AM, Ashish Khetan wrote: hii I am using MPC8641D based custom board for evaluation purpose. I am using minimal configuration for this board i.e. only FLASH and DDR initialisation. when I compiled U-boot in debug mode its printing addresses, i check for those addresses and found that it is unable to relocate itself to DDR(4*MT47H64M16). The following message was printed... U-Boot 2013.04 (Oct 25 2013 - 15:05:33) Unicore software on multiprocessor system!! To enable mutlticore build define CONFIG_MP CPU: 8641, Version: 2.1, (0x80900021) Core: E600 Core 0 (MSSCR0=8000, PORDEVSR=ab08307), Version: 2.2, (0x80040202) Clock Configuration: CPU:800 MHz, MPX:400 MHz DDR:200 MHz (400 MT/s data rate), LBC:25 MHz L1:D-cache 32 KB enabled I-cache 32 KB enabled L2:Disabled Board: Wind River SBC8641D DRAM: DDR: 512 MiB Top of RAM usable for U-Boot at: 2000 Reserving 114k for U-Boot at: 1ffe3000 Reserving 136k for malloc() at: 1ffc1000 Reserving 80 Bytes for Board Info at: 1ffc0fb0 Reserving 152 Bytes for Global Data at: 1ffc0f18 Stack Pointer at: 1ffc0f00 New Stack Pointer is: 1ffc0f00 and stuck here... Any pointer or link to get more about this will be helpful. Thanks in Advance ___ U-Boot mailing list U-Boot@lists.denx.de mailto:U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot Now its working... by default the data width of bus was 64bit and ddr2 was configured for 32-bit.. so i change the data width and now its working... Thanks a lot for lighting up the path... now i am trying to configure like CPU:1200 MHz, MPX:600 MHz DDR:300 MHz (600 MT/s data rate) but i its stucking before relocation... its working file at DDR 250Mhz.. is it because DDR or FLASH configuration.?? Thanks again and Regards ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] MPC8641D stucks before relocation
I disabled the 2nd core by using cfg_core1_enable and D2_MSRCID1 signal is not connected and we are using DDR controller 2... will this create any obstacles to relocate? Is there any other register configuration for DDR? can somebody help me to understand this or give me some pointer to get more understanding for this... I am getting frusted because I am stuck at this point from last 20 days. please help... thanks in advance and Regards On Sat, Oct 26, 2013 at 12:20 AM, Ashish Khetan curieux.khe...@gmail.comwrote: Thanks For reply, i check DDR configuration using Code warrior, and successfully getting read/write from DDR. I use the following configuration in code warrior and same in u-boot... writemem.l 0xf8006000 0x001f # CS0_BNDSwritemem.l 0xf8006080 0x80914102 # CS0_CONFIGwritemem.l0xf8006100 0x0007 # TIMING_CFG_3writemem.l0xf8006104 0xFF770F0F # TIMING_CFG_0 writemem.l 0xf8006108 0x7F78F777 # TIMING_CFG_1 writemem.l0xf800610C 0x00205114 # TIMING_CFG_2 writemem.l0xf8006110 0x43088008 # DDR_SDRAM_CFG writemem.l0xf8006114 0x24401000 # DDR_SDRAM_CFG2 writemem.l0xf8006118 0x43800E52 # DDR_SDRAM_MODE writemem.l 0xf800611C 0x8000C000 # DDR_SDRAM_MODE_2writemem.l0xf8006120 0x # DDR_SDRAM_MD_CNTL writemem.l0xf8006124 0x0508 # DDR_SDRAM_INTERVAL writemem.l0xf8006128 0x # DDR_DATA_INIT writemem.l0xf8006130 0x0380 # DDR_SDRAM_CLK_CNTL sleep 200 writemem.l0xf8006110 0xC3088008 # DDR_SDRAM_CFG but I did not understand... can you give some light on this. thanks again... On Fri, Oct 25, 2013 at 10:25 PM, York Sun york...@freescale.com wrote: It is probably because your DDR wasn't initialized correctly. You can try to dump all DDR registers and check if anyone is suspicious. You can also override any register before enabling the controller. You may also add some memory test before relocation. York On 10/25/2013 06:38 AM, Ashish Khetan wrote: hii I am using MPC8641D based custom board for evaluation purpose. I am using minimal configuration for this board i.e. only FLASH and DDR initialisation. when I compiled U-boot in debug mode its printing addresses, i check for those addresses and found that it is unable to relocate itself to DDR(4*MT47H64M16). The following message was printed... U-Boot 2013.04 (Oct 25 2013 - 15:05:33) Unicore software on multiprocessor system!! To enable mutlticore build define CONFIG_MP CPU: 8641, Version: 2.1, (0x80900021) Core: E600 Core 0 (MSSCR0=8000, PORDEVSR=ab08307), Version: 2.2, (0x80040202) Clock Configuration: CPU:800 MHz, MPX:400 MHz DDR:200 MHz (400 MT/s data rate), LBC:25 MHz L1:D-cache 32 KB enabled I-cache 32 KB enabled L2:Disabled Board: Wind River SBC8641D DRAM: DDR: 512 MiB Top of RAM usable for U-Boot at: 2000 Reserving 114k for U-Boot at: 1ffe3000 Reserving 136k for malloc() at: 1ffc1000 Reserving 80 Bytes for Board Info at: 1ffc0fb0 Reserving 152 Bytes for Global Data at: 1ffc0f18 Stack Pointer at: 1ffc0f00 New Stack Pointer is: 1ffc0f00 and stuck here... Any pointer or link to get more about this will be helpful. Thanks in Advance ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] MPC8641D stucks before relocation
I see you have relaxed most timing to the slowest. Debugging DDR is not about trial and error because there are so many parameters. Could you get some guidance from hardware designers? If you can't, I suggest you get the spec and do the math yourself, using the DDR driver we have in u-boot. BTW, your TIMING_CFG_2 seems to be fast. I don't know if that would cause any issue. Your mode register also seems suspicious. York On 10/28/2013 05:01 AM, Ashish Khetan wrote: I disabled the 2nd core by using cfg_core1_enable and D2_MSRCID1 signal is not connected and we are using DDR controller 2... will this create any obstacles to relocate? Is there any other register configuration for DDR? can somebody help me to understand this or give me some pointer to get more understanding for this... I am getting frusted because I am stuck at this point from last 20 days. please help... thanks in advance and Regards On Sat, Oct 26, 2013 at 12:20 AM, Ashish Khetan curieux.khe...@gmail.com mailto:curieux.khe...@gmail.com wrote: Thanks For reply, i check DDR configuration using Code warrior, and successfully getting read/write from DDR. I use the following configuration in code warrior and same in u-boot... writemem.l 0xf8006000 0x001f # CS0_BNDS writemem.l 0xf8006080 0x80914102 # CS0_CONFIG writemem.l0xf8006100 0x0007 # TIMING_CFG_3 writemem.l0xf8006104 0xFF770F0F # TIMING_CFG_0 writemem.l0xf8006108 0x7F78F777 # TIMING_CFG_1 writemem.l0xf800610C 0x00205114 # TIMING_CFG_2 writemem.l0xf8006110 0x43088008 # DDR_SDRAM_CFG writemem.l0xf8006114 0x24401000 # DDR_SDRAM_CFG2 writemem.l0xf8006118 0x43800E52 # DDR_SDRAM_MODE writemem.l0xf800611C 0x8000C000 # DDR_SDRAM_MODE_2 writemem.l0xf8006120 0x # DDR_SDRAM_MD_CNTL writemem.l0xf8006124 0x0508 # DDR_SDRAM_INTERVAL writemem.l0xf8006128 0x # DDR_DATA_INIT writemem.l0xf8006130 0x0380 # DDR_SDRAM_CLK_CNTL sleep 200 writemem.l0xf8006110 0xC3088008 # DDR_SDRAM_CFG but I did not understand... can you give some light on this. thanks again... On Fri, Oct 25, 2013 at 10:25 PM, York Sun york...@freescale.com mailto:york...@freescale.com wrote: It is probably because your DDR wasn't initialized correctly. You can try to dump all DDR registers and check if anyone is suspicious. You can also override any register before enabling the controller. You may also add some memory test before relocation. York On 10/25/2013 06:38 AM, Ashish Khetan wrote: hii I am using MPC8641D based custom board for evaluation purpose. I am using minimal configuration for this board i.e. only FLASH and DDR initialisation. when I compiled U-boot in debug mode its printing addresses, i check for those addresses and found that it is unable to relocate itself to DDR(4*MT47H64M16). The following message was printed... U-Boot 2013.04 (Oct 25 2013 - 15:05:33) Unicore software on multiprocessor system!! To enable mutlticore build define CONFIG_MP CPU: 8641, Version: 2.1, (0x80900021) Core: E600 Core 0 (MSSCR0=8000, PORDEVSR=ab08307), Version: 2.2, (0x80040202) Clock Configuration: CPU:800 MHz, MPX:400 MHz DDR:200 MHz (400 MT/s data rate), LBC:25 MHz L1:D-cache 32 KB enabled I-cache 32 KB enabled L2:Disabled Board: Wind River SBC8641D DRAM: DDR: 512 MiB Top of RAM usable for U-Boot at: 2000 Reserving 114k for U-Boot at: 1ffe3000 Reserving 136k for malloc() at: 1ffc1000 Reserving 80 Bytes for Board Info at: 1ffc0fb0 Reserving 152 Bytes for Global Data at: 1ffc0f18 Stack Pointer at: 1ffc0f00 New Stack Pointer is: 1ffc0f00 and stuck here... Any pointer or link to get more about this will be helpful. Thanks in Advance ___ U-Boot mailing list U-Boot@lists.denx.de mailto:U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
[U-Boot] MPC8641D stucks before relocation
hii I am using MPC8641D based custom board for evaluation purpose. I am using minimal configuration for this board i.e. only FLASH and DDR initialisation. when I compiled U-boot in debug mode its printing addresses, i check for those addresses and found that it is unable to relocate itself to DDR(4*MT47H64M16). The following message was printed... U-Boot 2013.04 (Oct 25 2013 - 15:05:33) Unicore software on multiprocessor system!! To enable mutlticore build define CONFIG_MP CPU: 8641, Version: 2.1, (0x80900021) Core: E600 Core 0 (MSSCR0=8000, PORDEVSR=ab08307), Version: 2.2, (0x80040202) Clock Configuration: CPU:800 MHz, MPX:400 MHz DDR:200 MHz (400 MT/s data rate), LBC:25 MHz L1:D-cache 32 KB enabled I-cache 32 KB enabled L2:Disabled Board: Wind River SBC8641D DRAM: DDR: 512 MiB Top of RAM usable for U-Boot at: 2000 Reserving 114k for U-Boot at: 1ffe3000 Reserving 136k for malloc() at: 1ffc1000 Reserving 80 Bytes for Board Info at: 1ffc0fb0 Reserving 152 Bytes for Global Data at: 1ffc0f18 Stack Pointer at: 1ffc0f00 New Stack Pointer is: 1ffc0f00 and stuck here... Any pointer or link to get more about this will be helpful. Thanks in Advance ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] MPC8641D stucks before relocation
It is probably because your DDR wasn't initialized correctly. You can try to dump all DDR registers and check if anyone is suspicious. You can also override any register before enabling the controller. You may also add some memory test before relocation. York On 10/25/2013 06:38 AM, Ashish Khetan wrote: hii I am using MPC8641D based custom board for evaluation purpose. I am using minimal configuration for this board i.e. only FLASH and DDR initialisation. when I compiled U-boot in debug mode its printing addresses, i check for those addresses and found that it is unable to relocate itself to DDR(4*MT47H64M16). The following message was printed... U-Boot 2013.04 (Oct 25 2013 - 15:05:33) Unicore software on multiprocessor system!! To enable mutlticore build define CONFIG_MP CPU: 8641, Version: 2.1, (0x80900021) Core: E600 Core 0 (MSSCR0=8000, PORDEVSR=ab08307), Version: 2.2, (0x80040202) Clock Configuration: CPU:800 MHz, MPX:400 MHz DDR:200 MHz (400 MT/s data rate), LBC:25 MHz L1:D-cache 32 KB enabled I-cache 32 KB enabled L2:Disabled Board: Wind River SBC8641D DRAM: DDR: 512 MiB Top of RAM usable for U-Boot at: 2000 Reserving 114k for U-Boot at: 1ffe3000 Reserving 136k for malloc() at: 1ffc1000 Reserving 80 Bytes for Board Info at: 1ffc0fb0 Reserving 152 Bytes for Global Data at: 1ffc0f18 Stack Pointer at: 1ffc0f00 New Stack Pointer is: 1ffc0f00 and stuck here... Any pointer or link to get more about this will be helpful. Thanks in Advance ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] MPC8641D stucks before relocation
Thanks For reply, i check DDR configuration using Code warrior, and successfully getting read/write from DDR. I use the following configuration in code warrior and same in u-boot... writemem.l 0xf8006000 0x001f # CS0_BNDS writemem.l 0xf8006080 0x80914102 # CS0_CONFIG writemem.l0xf8006100 0x0007 # TIMING_CFG_3 writemem.l0xf8006104 0xFF770F0F # TIMING_CFG_0 writemem.l 0xf8006108 0x7F78F777 # TIMING_CFG_1 writemem.l0xf800610C 0x00205114 # TIMING_CFG_2 writemem.l0xf8006110 0x43088008 # DDR_SDRAM_CFG writemem.l0xf8006114 0x24401000 # DDR_SDRAM_CFG2 writemem.l0xf8006118 0x43800E52 # DDR_SDRAM_MODE writemem.l 0xf800611C 0x8000C000 # DDR_SDRAM_MODE_2 writemem.l0xf8006120 0x # DDR_SDRAM_MD_CNTL writemem.l0xf8006124 0x0508 # DDR_SDRAM_INTERVAL writemem.l0xf8006128 0x # DDR_DATA_INIT writemem.l0xf8006130 0x0380 # DDR_SDRAM_CLK_CNTL sleep 200 writemem.l0xf8006110 0xC3088008 # DDR_SDRAM_CFG but I did not understand... can you give some light on this. thanks again... On Fri, Oct 25, 2013 at 10:25 PM, York Sun york...@freescale.com wrote: It is probably because your DDR wasn't initialized correctly. You can try to dump all DDR registers and check if anyone is suspicious. You can also override any register before enabling the controller. You may also add some memory test before relocation. York On 10/25/2013 06:38 AM, Ashish Khetan wrote: hii I am using MPC8641D based custom board for evaluation purpose. I am using minimal configuration for this board i.e. only FLASH and DDR initialisation. when I compiled U-boot in debug mode its printing addresses, i check for those addresses and found that it is unable to relocate itself to DDR(4*MT47H64M16). The following message was printed... U-Boot 2013.04 (Oct 25 2013 - 15:05:33) Unicore software on multiprocessor system!! To enable mutlticore build define CONFIG_MP CPU: 8641, Version: 2.1, (0x80900021) Core: E600 Core 0 (MSSCR0=8000, PORDEVSR=ab08307), Version: 2.2, (0x80040202) Clock Configuration: CPU:800 MHz, MPX:400 MHz DDR:200 MHz (400 MT/s data rate), LBC:25 MHz L1:D-cache 32 KB enabled I-cache 32 KB enabled L2:Disabled Board: Wind River SBC8641D DRAM: DDR: 512 MiB Top of RAM usable for U-Boot at: 2000 Reserving 114k for U-Boot at: 1ffe3000 Reserving 136k for malloc() at: 1ffc1000 Reserving 80 Bytes for Board Info at: 1ffc0fb0 Reserving 152 Bytes for Global Data at: 1ffc0f18 Stack Pointer at: 1ffc0f00 New Stack Pointer is: 1ffc0f00 and stuck here... Any pointer or link to get more about this will be helpful. Thanks in Advance ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
