Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
Hi, On Wed, Dec 19, 2018 at 5:05 PM Bin Meng wrote: > > Hi Anup, > > On Wed, Dec 19, 2018 at 2:32 PM Anup Patel wrote: > > > > On Wed, Dec 19, 2018 at 11:02 AM Bin Meng wrote: > > > > > > Hi Anup, > > > > > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel wrote: > > > > > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng wrote: > > > > > > > > > > Hi Anup, > > > > > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel > > > > > wrote: > > > > > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng wrote: > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > > > wrote: > > > > > > > > > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > > > > > > works fine for QEMU sifive_u machince in both M-mode and > > > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > > > > applied to QEMU sources: > > > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to instantiate the > > > > > > > MACB? > > > > > > > "-device ?" does not give me anything that looks like MACB. > > > > > > > Without a > > > > > > > proper "-device " parameter, I can boot U-Boot on QEMU sifive_u > > > > > > > and > > > > > > > see U-Boot driver is probed, but a simple 'ping' test does not > > > > > > > work. > > > > > > > > > > > > Try the following: > > > > > > # setenv ipaddr 10.0.2.1 > > > > > > # ping 10.0.2.2 > > > > > > > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > > > > > The above works for me on QEMU. > > > > > > > > > > My understanding is that we need enable QEMU network via "-netdev " > > > > > (either usr, or tap), with a corresponding "-device". I don't know how > > > > > to set it up. What's your command line to test this? > > > > > > > > > > > > > "-netdev" or "-device" parameters are not mandatory. By default, virtual > > > > NICs are in NAT mode. The QEMU NAT gateway is at IP address > > > > 10.0.2.2. We can always ping the NAT gateway when virtual NIC is in > > > > NAT mode. > > > > > > > > Here's how I compile for M-mode: > > > > # ARCH=riscv > > > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > > > # make qemu-riscv64_defconfig > > > > # make > > > > > > > > My U-boot log is as follows: > > > > > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ qemu-system-riscv64 -M > > > > sifive_u -m 256M -display none -serial stdio -kernel ./u-boot > > > > > > > > > > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 +0530) > > > > > > > > CPU: rv64imafdcsu > > > > Model: ucbbar,spike-bare,qemu > > > > DRAM: 256 MiB > > > > In:uart@10013000 > > > > Out: uart@10013000 > > > > Err: uart@10013000 > > > > Net: > > > > Warning: ethernet@100900fc (eth0) using random MAC address - > > > > f6:1f:8c:13:83:c0 > > > > eth0: ethernet@100900fc > > > > Hit any key to stop autoboot: 0 > > > > > > > > Device 0: unknown device > > > > ethernet@100900fc: PHY present at 0 > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > BOOTP broadcast 1 > > > > DHCP client bound to address 10.0.2.15 (2 ms) > > > > Using ethernet@100900fc device > > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > > Filename 'boot.scr.uimg'. > > > > Load address: 0x8210 > > > > Loading: * > > > > TFTP error: 'Access violation' (2) > > > > Not retrying... > > > > ethernet@100900fc: PHY present at 0 > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > BOOTP broadcast 1 > > > > DHCP client bound to address 10.0.2.15 (1 ms) > > > > Using ethernet@100900fc device > > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > > Filename 'boot.scr.uimg'. > > > > Load address: 0x8100 > > > > Loading: * > > > > TFTP error: 'Access violation' (2) > > > > Not retrying... > > > > => ping 10.0.2.2 > > > > ethernet@100900fc: PHY present at 0 > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > Using ethernet@100900fc device > > > > host 10.0.2.2 is alive > > > > => > > > > ethernet@100900fc: PHY present at 0 > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > Using ethernet@100900fc device > > > > host 10.0.2.2 is alive > > > > => qemu-system-riscv64: terminating on signal 2 > > > > > > > > > > I have always been using "qemu-system-riscv64 -nographic -M sifive_u > > > -kernel u-boot" to test U-Boot on qemu risc-v. > > > With above command, I can "ping 10.0.2.2" and get the exact the same > > > re
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
On Mon, Dec 24, 2018 at 1:06 PM Bin Meng wrote: > > Hi Anup, > > On Mon, Dec 24, 2018 at 3:23 PM Anup Patel wrote: > > > > On Mon, Dec 24, 2018 at 12:45 PM Bin Meng wrote: > > > > > > Hi Anup, > > > > > > On Mon, Dec 24, 2018 at 2:42 PM Anup Patel wrote: > > > > > > > > On Mon, Dec 24, 2018 at 12:01 PM Bin Meng wrote: > > > > > > > > > > Hi Anup, > > > > > > > > > > On Mon, Dec 24, 2018 at 1:41 PM Anup Patel > > > > > wrote: > > > > > > > > > > > > On Mon, Dec 24, 2018 at 6:59 AM Bin Meng wrote: > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > On Wed, Dec 19, 2018 at 5:05 PM Bin Meng > > > > > > > wrote: > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > On Wed, Dec 19, 2018 at 2:32 PM Anup Patel > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > On Wed, Dec 19, 2018 at 11:02 AM Bin Meng > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng > > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel > > > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng > > > > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > This patchset enables Cadance MACB ethernet > > > > > > > > > > > > > > > driver for > > > > > > > > > > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet > > > > > > > > > > > > > > > driver > > > > > > > > > > > > > > > works fine for QEMU sifive_u machince in both > > > > > > > > > > > > > > > M-mode and > > > > > > > > > > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot > > > > > > > > > > > > > > > tree > > > > > > > > > > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > > > > > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > To try on QEMU, please ensure following patches > > > > > > > > > > > > > > > are > > > > > > > > > > > > > > > applied to QEMU sources: > > > > > > > > > > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > > > > > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to > > > > > > > > > > > > > > instantiate the MACB? > > > > > > > > > > > > > > "-device ?" does not give me anything that looks > > > > > > > > > > > > > > like MACB. Without a > > > > > > > > > > > > > > proper "-device " parameter, I can boot U-Boot on > > > > > > > > > > > > > > QEMU sifive_u and > > > > > > > > > > > > > > see U-Boot driver is probed, but a simple 'ping' > > > > > > > > > > > > > > test does not work. > > > > > > > > > > > > > > > > > > > > > > > > > > Try the following: > > > > > > > > > > > > > # setenv ipaddr 10.0.2.1 > > > > > > > > > > > > > # ping 10.0.2.2 > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > > > > > > > > > > > > > > > > > > > The above works for me on QEMU. > > > > > > > > > > > > > > > > > > > > > > > > My understanding is that we need enable QEMU network > > > > > > > > > > > > via "-netdev " > > > > > > > > > > > > (either usr, or tap), with a corresponding "-device". I > > > > > > > > > > > > don't know how > > > > > > > > > > > > to set it up. What's your command line to test this? > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > "-netdev" or "-device" parameters are not mandatory. By > > > > > > > > > > > default, virtual > > > > > > > > > > > NICs are in NAT mode. The QEMU NAT gateway is at IP > > > > > > > > > > > address > > > > > > > > > > > 10.0.2.2. We can always ping the NAT gateway when virtual > > > > > > > > > > > NIC is in > > > > > > > > > > > NAT mode. > > > > > > > > > > > > > > > > > > > > > > Here's how I compile for M-mode: > > > > > > > > > > > # ARCH=riscv > > > > > > > > > > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > > > > > > > > > > # make qemu-riscv64_defconfig > > > > > > > > > > > # make > > > > > > > > > > > > > > > > > > > > > > My U-boot log is as follows: > > > > > > > > > > > > > > > > > > > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ > > > > > > > > > > > qemu-system-riscv64 -M > > > > > > > > > > > sifive_u -m 256M -display none -serial stdio -kernel > > > > >
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
Hi Anup, On Mon, Dec 24, 2018 at 3:23 PM Anup Patel wrote: > > On Mon, Dec 24, 2018 at 12:45 PM Bin Meng wrote: > > > > Hi Anup, > > > > On Mon, Dec 24, 2018 at 2:42 PM Anup Patel wrote: > > > > > > On Mon, Dec 24, 2018 at 12:01 PM Bin Meng wrote: > > > > > > > > Hi Anup, > > > > > > > > On Mon, Dec 24, 2018 at 1:41 PM Anup Patel wrote: > > > > > > > > > > On Mon, Dec 24, 2018 at 6:59 AM Bin Meng wrote: > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > On Wed, Dec 19, 2018 at 5:05 PM Bin Meng wrote: > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > On Wed, Dec 19, 2018 at 2:32 PM Anup Patel > > > > > > > wrote: > > > > > > > > > > > > > > > > On Wed, Dec 19, 2018 at 11:02 AM Bin Meng > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel > > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng > > > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > > > > > > > This patchset enables Cadance MACB ethernet driver > > > > > > > > > > > > > > for > > > > > > > > > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet > > > > > > > > > > > > > > driver > > > > > > > > > > > > > > works fine for QEMU sifive_u machince in both > > > > > > > > > > > > > > M-mode and > > > > > > > > > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > > > > > > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > > > > > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > > > > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > > > > > > > > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > > > > > > > > > > applied to QEMU sources: > > > > > > > > > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > > > > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to > > > > > > > > > > > > > instantiate the MACB? > > > > > > > > > > > > > "-device ?" does not give me anything that looks like > > > > > > > > > > > > > MACB. Without a > > > > > > > > > > > > > proper "-device " parameter, I can boot U-Boot on > > > > > > > > > > > > > QEMU sifive_u and > > > > > > > > > > > > > see U-Boot driver is probed, but a simple 'ping' test > > > > > > > > > > > > > does not work. > > > > > > > > > > > > > > > > > > > > > > > > Try the following: > > > > > > > > > > > > # setenv ipaddr 10.0.2.1 > > > > > > > > > > > > # ping 10.0.2.2 > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > > > > > > > > > > > > > > > > > The above works for me on QEMU. > > > > > > > > > > > > > > > > > > > > > > My understanding is that we need enable QEMU network via > > > > > > > > > > > "-netdev " > > > > > > > > > > > (either usr, or tap), with a corresponding "-device". I > > > > > > > > > > > don't know how > > > > > > > > > > > to set it up. What's your command line to test this? > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > "-netdev" or "-device" parameters are not mandatory. By > > > > > > > > > > default, virtual > > > > > > > > > > NICs are in NAT mode. The QEMU NAT gateway is at IP address > > > > > > > > > > 10.0.2.2. We can always ping the NAT gateway when virtual > > > > > > > > > > NIC is in > > > > > > > > > > NAT mode. > > > > > > > > > > > > > > > > > > > > Here's how I compile for M-mode: > > > > > > > > > > # ARCH=riscv > > > > > > > > > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > > > > > > > > > # make qemu-riscv64_defconfig > > > > > > > > > > # make > > > > > > > > > > > > > > > > > > > > My U-boot log is as follows: > > > > > > > > > > > > > > > > > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ > > > > > > > > > > qemu-system-riscv64 -M > > > > > > > > > > sifive_u -m 256M -display none -serial stdio -kernel > > > > > > > > > > ./u-boot > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - > > > > > > > > > > 10:05:50 +0530) > > > > > > > > > > > > > > > > > > > > CPU: rv64imafdcsu > > > > > > > > > > Model: ucbbar,spike-bare,qemu > > > > > > > > > > DRAM: 256 MiB > > > > > > > > > > In:uart@10013000 > > > > > > > > > > Out: uart
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
On Mon, Dec 24, 2018 at 12:45 PM Bin Meng wrote: > > Hi Anup, > > On Mon, Dec 24, 2018 at 2:42 PM Anup Patel wrote: > > > > On Mon, Dec 24, 2018 at 12:01 PM Bin Meng wrote: > > > > > > Hi Anup, > > > > > > On Mon, Dec 24, 2018 at 1:41 PM Anup Patel wrote: > > > > > > > > On Mon, Dec 24, 2018 at 6:59 AM Bin Meng wrote: > > > > > > > > > > Hi Anup, > > > > > > > > > > On Wed, Dec 19, 2018 at 5:05 PM Bin Meng wrote: > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > On Wed, Dec 19, 2018 at 2:32 PM Anup Patel > > > > > > wrote: > > > > > > > > > > > > > > On Wed, Dec 19, 2018 at 11:02 AM Bin Meng > > > > > > > wrote: > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng > > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > > > > > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet > > > > > > > > > > > > > driver > > > > > > > > > > > > > works fine for QEMU sifive_u machince in both M-mode > > > > > > > > > > > > > and > > > > > > > > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > > > > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > > > > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > > > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > > > > > > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > > > > > > > > > applied to QEMU sources: > > > > > > > > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > > > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to > > > > > > > > > > > > instantiate the MACB? > > > > > > > > > > > > "-device ?" does not give me anything that looks like > > > > > > > > > > > > MACB. Without a > > > > > > > > > > > > proper "-device " parameter, I can boot U-Boot on QEMU > > > > > > > > > > > > sifive_u and > > > > > > > > > > > > see U-Boot driver is probed, but a simple 'ping' test > > > > > > > > > > > > does not work. > > > > > > > > > > > > > > > > > > > > > > Try the following: > > > > > > > > > > > # setenv ipaddr 10.0.2.1 > > > > > > > > > > > # ping 10.0.2.2 > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > > > > > > > > > > > > > > > The above works for me on QEMU. > > > > > > > > > > > > > > > > > > > > My understanding is that we need enable QEMU network via > > > > > > > > > > "-netdev " > > > > > > > > > > (either usr, or tap), with a corresponding "-device". I > > > > > > > > > > don't know how > > > > > > > > > > to set it up. What's your command line to test this? > > > > > > > > > > > > > > > > > > > > > > > > > > > > "-netdev" or "-device" parameters are not mandatory. By > > > > > > > > > default, virtual > > > > > > > > > NICs are in NAT mode. The QEMU NAT gateway is at IP address > > > > > > > > > 10.0.2.2. We can always ping the NAT gateway when virtual NIC > > > > > > > > > is in > > > > > > > > > NAT mode. > > > > > > > > > > > > > > > > > > Here's how I compile for M-mode: > > > > > > > > > # ARCH=riscv > > > > > > > > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > > > > > > > > # make qemu-riscv64_defconfig > > > > > > > > > # make > > > > > > > > > > > > > > > > > > My U-boot log is as follows: > > > > > > > > > > > > > > > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ > > > > > > > > > qemu-system-riscv64 -M > > > > > > > > > sifive_u -m 256M -display none -serial stdio -kernel ./u-boot > > > > > > > > > > > > > > > > > > > > > > > > > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 > > > > > > > > > +0530) > > > > > > > > > > > > > > > > > > CPU: rv64imafdcsu > > > > > > > > > Model: ucbbar,spike-bare,qemu > > > > > > > > > DRAM: 256 MiB > > > > > > > > > In:uart@10013000 > > > > > > > > > Out: uart@10013000 > > > > > > > > > Err: uart@10013000 > > > > > > > > > Net: > > > > > > > > > Warning: ethernet@100900fc (eth0) using random MAC address - > > > > > > > > > f6:1f:8c:13:83:c0 > > > > > > > > > eth0: ethernet@100900fc > > > > > > > > > Hit any key to stop autoboot: 0 > > > > > > > > > > > > > > > > > > Device 0: unknown device > > >
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
Hi Anup, On Mon, Dec 24, 2018 at 2:42 PM Anup Patel wrote: > > On Mon, Dec 24, 2018 at 12:01 PM Bin Meng wrote: > > > > Hi Anup, > > > > On Mon, Dec 24, 2018 at 1:41 PM Anup Patel wrote: > > > > > > On Mon, Dec 24, 2018 at 6:59 AM Bin Meng wrote: > > > > > > > > Hi Anup, > > > > > > > > On Wed, Dec 19, 2018 at 5:05 PM Bin Meng wrote: > > > > > > > > > > Hi Anup, > > > > > > > > > > On Wed, Dec 19, 2018 at 2:32 PM Anup Patel > > > > > wrote: > > > > > > > > > > > > On Wed, Dec 19, 2018 at 11:02 AM Bin Meng > > > > > > wrote: > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel > > > > > > > wrote: > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > > > > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > > > > > > > > > > works fine for QEMU sifive_u machince in both M-mode and > > > > > > > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > > > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > > > > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > > > > > > > > applied to QEMU sources: > > > > > > > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to > > > > > > > > > > > instantiate the MACB? > > > > > > > > > > > "-device ?" does not give me anything that looks like > > > > > > > > > > > MACB. Without a > > > > > > > > > > > proper "-device " parameter, I can boot U-Boot on QEMU > > > > > > > > > > > sifive_u and > > > > > > > > > > > see U-Boot driver is probed, but a simple 'ping' test > > > > > > > > > > > does not work. > > > > > > > > > > > > > > > > > > > > Try the following: > > > > > > > > > > # setenv ipaddr 10.0.2.1 > > > > > > > > > > # ping 10.0.2.2 > > > > > > > > > > > > > > > > > > > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > > > > > > > > > > > > > The above works for me on QEMU. > > > > > > > > > > > > > > > > > > My understanding is that we need enable QEMU network via > > > > > > > > > "-netdev " > > > > > > > > > (either usr, or tap), with a corresponding "-device". I don't > > > > > > > > > know how > > > > > > > > > to set it up. What's your command line to test this? > > > > > > > > > > > > > > > > > > > > > > > > > "-netdev" or "-device" parameters are not mandatory. By > > > > > > > > default, virtual > > > > > > > > NICs are in NAT mode. The QEMU NAT gateway is at IP address > > > > > > > > 10.0.2.2. We can always ping the NAT gateway when virtual NIC > > > > > > > > is in > > > > > > > > NAT mode. > > > > > > > > > > > > > > > > Here's how I compile for M-mode: > > > > > > > > # ARCH=riscv > > > > > > > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > > > > > > > # make qemu-riscv64_defconfig > > > > > > > > # make > > > > > > > > > > > > > > > > My U-boot log is as follows: > > > > > > > > > > > > > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ > > > > > > > > qemu-system-riscv64 -M > > > > > > > > sifive_u -m 256M -display none -serial stdio -kernel ./u-boot > > > > > > > > > > > > > > > > > > > > > > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 > > > > > > > > +0530) > > > > > > > > > > > > > > > > CPU: rv64imafdcsu > > > > > > > > Model: ucbbar,spike-bare,qemu > > > > > > > > DRAM: 256 MiB > > > > > > > > In:uart@10013000 > > > > > > > > Out: uart@10013000 > > > > > > > > Err: uart@10013000 > > > > > > > > Net: > > > > > > > > Warning: ethernet@100900fc (eth0) using random MAC address - > > > > > > > > f6:1f:8c:13:83:c0 > > > > > > > > eth0: ethernet@100900fc > > > > > > > > Hit any key to stop autoboot: 0 > > > > > > > > > > > > > > > > Device 0: unknown device > > > > > > > > ethernet@100900fc: PHY present at 0 > > > > > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > > > > > BOOTP broadcast 1 > > > > > > > > DHCP client bound to address 10.0.2.15 (2 ms) > > > > > > > > Using ethernet@100900fc device > > > > > > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > >
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
On Mon, Dec 24, 2018 at 12:01 PM Bin Meng wrote: > > Hi Anup, > > On Mon, Dec 24, 2018 at 1:41 PM Anup Patel wrote: > > > > On Mon, Dec 24, 2018 at 6:59 AM Bin Meng wrote: > > > > > > Hi Anup, > > > > > > On Wed, Dec 19, 2018 at 5:05 PM Bin Meng wrote: > > > > > > > > Hi Anup, > > > > > > > > On Wed, Dec 19, 2018 at 2:32 PM Anup Patel wrote: > > > > > > > > > > On Wed, Dec 19, 2018 at 11:02 AM Bin Meng wrote: > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel > > > > > > wrote: > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng > > > > > > > wrote: > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > > > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > > > > > > > > > works fine for QEMU sifive_u machince in both M-mode and > > > > > > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > > > > > > > applied to QEMU sources: > > > > > > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to instantiate > > > > > > > > > > the MACB? > > > > > > > > > > "-device ?" does not give me anything that looks like MACB. > > > > > > > > > > Without a > > > > > > > > > > proper "-device " parameter, I can boot U-Boot on QEMU > > > > > > > > > > sifive_u and > > > > > > > > > > see U-Boot driver is probed, but a simple 'ping' test does > > > > > > > > > > not work. > > > > > > > > > > > > > > > > > > Try the following: > > > > > > > > > # setenv ipaddr 10.0.2.1 > > > > > > > > > # ping 10.0.2.2 > > > > > > > > > > > > > > > > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > > > > > > > > > > > The above works for me on QEMU. > > > > > > > > > > > > > > > > My understanding is that we need enable QEMU network via > > > > > > > > "-netdev " > > > > > > > > (either usr, or tap), with a corresponding "-device". I don't > > > > > > > > know how > > > > > > > > to set it up. What's your command line to test this? > > > > > > > > > > > > > > > > > > > > > > "-netdev" or "-device" parameters are not mandatory. By default, > > > > > > > virtual > > > > > > > NICs are in NAT mode. The QEMU NAT gateway is at IP address > > > > > > > 10.0.2.2. We can always ping the NAT gateway when virtual NIC is > > > > > > > in > > > > > > > NAT mode. > > > > > > > > > > > > > > Here's how I compile for M-mode: > > > > > > > # ARCH=riscv > > > > > > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > > > > > > # make qemu-riscv64_defconfig > > > > > > > # make > > > > > > > > > > > > > > My U-boot log is as follows: > > > > > > > > > > > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ qemu-system-riscv64 > > > > > > > -M > > > > > > > sifive_u -m 256M -display none -serial stdio -kernel ./u-boot > > > > > > > > > > > > > > > > > > > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 > > > > > > > +0530) > > > > > > > > > > > > > > CPU: rv64imafdcsu > > > > > > > Model: ucbbar,spike-bare,qemu > > > > > > > DRAM: 256 MiB > > > > > > > In:uart@10013000 > > > > > > > Out: uart@10013000 > > > > > > > Err: uart@10013000 > > > > > > > Net: > > > > > > > Warning: ethernet@100900fc (eth0) using random MAC address - > > > > > > > f6:1f:8c:13:83:c0 > > > > > > > eth0: ethernet@100900fc > > > > > > > Hit any key to stop autoboot: 0 > > > > > > > > > > > > > > Device 0: unknown device > > > > > > > ethernet@100900fc: PHY present at 0 > > > > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > > > > BOOTP broadcast 1 > > > > > > > DHCP client bound to address 10.0.2.15 (2 ms) > > > > > > > Using ethernet@100900fc device > > > > > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > > > > > Filename 'boot.scr.uimg'. > > > > > > > Load address: 0x8210 > > > > > > > Loading: * > > > > > > > TFTP error: 'Access violation' (2) > > > > > > > Not retrying... > > > > > > > ethernet@100900fc: PHY present at 0 > > > > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > > > > BOOTP broadcas
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
Hi Anup, On Mon, Dec 24, 2018 at 1:41 PM Anup Patel wrote: > > On Mon, Dec 24, 2018 at 6:59 AM Bin Meng wrote: > > > > Hi Anup, > > > > On Wed, Dec 19, 2018 at 5:05 PM Bin Meng wrote: > > > > > > Hi Anup, > > > > > > On Wed, Dec 19, 2018 at 2:32 PM Anup Patel wrote: > > > > > > > > On Wed, Dec 19, 2018 at 11:02 AM Bin Meng wrote: > > > > > > > > > > Hi Anup, > > > > > > > > > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel > > > > > wrote: > > > > > > > > > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng wrote: > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel > > > > > > > wrote: > > > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > > > > > > > > works fine for QEMU sifive_u machince in both M-mode and > > > > > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > > > > > > applied to QEMU sources: > > > > > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to instantiate > > > > > > > > > the MACB? > > > > > > > > > "-device ?" does not give me anything that looks like MACB. > > > > > > > > > Without a > > > > > > > > > proper "-device " parameter, I can boot U-Boot on QEMU > > > > > > > > > sifive_u and > > > > > > > > > see U-Boot driver is probed, but a simple 'ping' test does > > > > > > > > > not work. > > > > > > > > > > > > > > > > Try the following: > > > > > > > > # setenv ipaddr 10.0.2.1 > > > > > > > > # ping 10.0.2.2 > > > > > > > > > > > > > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > > > > > > > > > The above works for me on QEMU. > > > > > > > > > > > > > > My understanding is that we need enable QEMU network via "-netdev > > > > > > > " > > > > > > > (either usr, or tap), with a corresponding "-device". I don't > > > > > > > know how > > > > > > > to set it up. What's your command line to test this? > > > > > > > > > > > > > > > > > > > "-netdev" or "-device" parameters are not mandatory. By default, > > > > > > virtual > > > > > > NICs are in NAT mode. The QEMU NAT gateway is at IP address > > > > > > 10.0.2.2. We can always ping the NAT gateway when virtual NIC is in > > > > > > NAT mode. > > > > > > > > > > > > Here's how I compile for M-mode: > > > > > > # ARCH=riscv > > > > > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > > > > > # make qemu-riscv64_defconfig > > > > > > # make > > > > > > > > > > > > My U-boot log is as follows: > > > > > > > > > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ qemu-system-riscv64 -M > > > > > > sifive_u -m 256M -display none -serial stdio -kernel ./u-boot > > > > > > > > > > > > > > > > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 +0530) > > > > > > > > > > > > CPU: rv64imafdcsu > > > > > > Model: ucbbar,spike-bare,qemu > > > > > > DRAM: 256 MiB > > > > > > In:uart@10013000 > > > > > > Out: uart@10013000 > > > > > > Err: uart@10013000 > > > > > > Net: > > > > > > Warning: ethernet@100900fc (eth0) using random MAC address - > > > > > > f6:1f:8c:13:83:c0 > > > > > > eth0: ethernet@100900fc > > > > > > Hit any key to stop autoboot: 0 > > > > > > > > > > > > Device 0: unknown device > > > > > > ethernet@100900fc: PHY present at 0 > > > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > > > BOOTP broadcast 1 > > > > > > DHCP client bound to address 10.0.2.15 (2 ms) > > > > > > Using ethernet@100900fc device > > > > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > > > > Filename 'boot.scr.uimg'. > > > > > > Load address: 0x8210 > > > > > > Loading: * > > > > > > TFTP error: 'Access violation' (2) > > > > > > Not retrying... > > > > > > ethernet@100900fc: PHY present at 0 > > > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > > > BOOTP broadcast 1 > > > > > > DHCP client bound to address 10.0.2.15 (1 ms) > > > > > > Using ethernet@100900fc device > > > > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > > > > Filename 'boot.scr.uimg'. > > > > > > Load address: 0x8100 > > > > > > Loading: * > > > > > > TFTP error: 'Access violation' (2) > > > > > > Not retrying... > > > > > >
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
On Mon, Dec 24, 2018 at 6:59 AM Bin Meng wrote: > > Hi Anup, > > On Wed, Dec 19, 2018 at 5:05 PM Bin Meng wrote: > > > > Hi Anup, > > > > On Wed, Dec 19, 2018 at 2:32 PM Anup Patel wrote: > > > > > > On Wed, Dec 19, 2018 at 11:02 AM Bin Meng wrote: > > > > > > > > Hi Anup, > > > > > > > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel wrote: > > > > > > > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng wrote: > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel > > > > > > wrote: > > > > > > > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng > > > > > > > wrote: > > > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > > > > wrote: > > > > > > > > > > > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > > > > > > > works fine for QEMU sifive_u machince in both M-mode and > > > > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > > > > > applied to QEMU sources: > > > > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to instantiate the > > > > > > > > MACB? > > > > > > > > "-device ?" does not give me anything that looks like MACB. > > > > > > > > Without a > > > > > > > > proper "-device " parameter, I can boot U-Boot on QEMU sifive_u > > > > > > > > and > > > > > > > > see U-Boot driver is probed, but a simple 'ping' test does not > > > > > > > > work. > > > > > > > > > > > > > > Try the following: > > > > > > > # setenv ipaddr 10.0.2.1 > > > > > > > # ping 10.0.2.2 > > > > > > > > > > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > > > > > > > The above works for me on QEMU. > > > > > > > > > > > > My understanding is that we need enable QEMU network via "-netdev " > > > > > > (either usr, or tap), with a corresponding "-device". I don't know > > > > > > how > > > > > > to set it up. What's your command line to test this? > > > > > > > > > > > > > > > > "-netdev" or "-device" parameters are not mandatory. By default, > > > > > virtual > > > > > NICs are in NAT mode. The QEMU NAT gateway is at IP address > > > > > 10.0.2.2. We can always ping the NAT gateway when virtual NIC is in > > > > > NAT mode. > > > > > > > > > > Here's how I compile for M-mode: > > > > > # ARCH=riscv > > > > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > > > > # make qemu-riscv64_defconfig > > > > > # make > > > > > > > > > > My U-boot log is as follows: > > > > > > > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ qemu-system-riscv64 -M > > > > > sifive_u -m 256M -display none -serial stdio -kernel ./u-boot > > > > > > > > > > > > > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 +0530) > > > > > > > > > > CPU: rv64imafdcsu > > > > > Model: ucbbar,spike-bare,qemu > > > > > DRAM: 256 MiB > > > > > In:uart@10013000 > > > > > Out: uart@10013000 > > > > > Err: uart@10013000 > > > > > Net: > > > > > Warning: ethernet@100900fc (eth0) using random MAC address - > > > > > f6:1f:8c:13:83:c0 > > > > > eth0: ethernet@100900fc > > > > > Hit any key to stop autoboot: 0 > > > > > > > > > > Device 0: unknown device > > > > > ethernet@100900fc: PHY present at 0 > > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > > BOOTP broadcast 1 > > > > > DHCP client bound to address 10.0.2.15 (2 ms) > > > > > Using ethernet@100900fc device > > > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > > > Filename 'boot.scr.uimg'. > > > > > Load address: 0x8210 > > > > > Loading: * > > > > > TFTP error: 'Access violation' (2) > > > > > Not retrying... > > > > > ethernet@100900fc: PHY present at 0 > > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > > BOOTP broadcast 1 > > > > > DHCP client bound to address 10.0.2.15 (1 ms) > > > > > Using ethernet@100900fc device > > > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > > > Filename 'boot.scr.uimg'. > > > > > Load address: 0x8100 > > > > > Loading: * > > > > > TFTP error: 'Access violation' (2) > > > > > Not retrying... > > > > > => ping 10.0.2.2 > > > > > ethernet@100900fc: PHY present at 0 > > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > > Using ethernet@100900fc device > > > > > host 10.0.2.2 is alive > > > > > => > > > > > ethernet@100900fc: PHY present at 0 > > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) >
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
Hi Anup, On Wed, Dec 19, 2018 at 5:05 PM Bin Meng wrote: > > Hi Anup, > > On Wed, Dec 19, 2018 at 2:32 PM Anup Patel wrote: > > > > On Wed, Dec 19, 2018 at 11:02 AM Bin Meng wrote: > > > > > > Hi Anup, > > > > > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel wrote: > > > > > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng wrote: > > > > > > > > > > Hi Anup, > > > > > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel > > > > > wrote: > > > > > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng wrote: > > > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > > > wrote: > > > > > > > > > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > > > > > > works fine for QEMU sifive_u machince in both M-mode and > > > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > > > > applied to QEMU sources: > > > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to instantiate the > > > > > > > MACB? > > > > > > > "-device ?" does not give me anything that looks like MACB. > > > > > > > Without a > > > > > > > proper "-device " parameter, I can boot U-Boot on QEMU sifive_u > > > > > > > and > > > > > > > see U-Boot driver is probed, but a simple 'ping' test does not > > > > > > > work. > > > > > > > > > > > > Try the following: > > > > > > # setenv ipaddr 10.0.2.1 > > > > > > # ping 10.0.2.2 > > > > > > > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > > > > > The above works for me on QEMU. > > > > > > > > > > My understanding is that we need enable QEMU network via "-netdev " > > > > > (either usr, or tap), with a corresponding "-device". I don't know how > > > > > to set it up. What's your command line to test this? > > > > > > > > > > > > > "-netdev" or "-device" parameters are not mandatory. By default, virtual > > > > NICs are in NAT mode. The QEMU NAT gateway is at IP address > > > > 10.0.2.2. We can always ping the NAT gateway when virtual NIC is in > > > > NAT mode. > > > > > > > > Here's how I compile for M-mode: > > > > # ARCH=riscv > > > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > > > # make qemu-riscv64_defconfig > > > > # make > > > > > > > > My U-boot log is as follows: > > > > > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ qemu-system-riscv64 -M > > > > sifive_u -m 256M -display none -serial stdio -kernel ./u-boot > > > > > > > > > > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 +0530) > > > > > > > > CPU: rv64imafdcsu > > > > Model: ucbbar,spike-bare,qemu > > > > DRAM: 256 MiB > > > > In:uart@10013000 > > > > Out: uart@10013000 > > > > Err: uart@10013000 > > > > Net: > > > > Warning: ethernet@100900fc (eth0) using random MAC address - > > > > f6:1f:8c:13:83:c0 > > > > eth0: ethernet@100900fc > > > > Hit any key to stop autoboot: 0 > > > > > > > > Device 0: unknown device > > > > ethernet@100900fc: PHY present at 0 > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > BOOTP broadcast 1 > > > > DHCP client bound to address 10.0.2.15 (2 ms) > > > > Using ethernet@100900fc device > > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > > Filename 'boot.scr.uimg'. > > > > Load address: 0x8210 > > > > Loading: * > > > > TFTP error: 'Access violation' (2) > > > > Not retrying... > > > > ethernet@100900fc: PHY present at 0 > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > BOOTP broadcast 1 > > > > DHCP client bound to address 10.0.2.15 (1 ms) > > > > Using ethernet@100900fc device > > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > > Filename 'boot.scr.uimg'. > > > > Load address: 0x8100 > > > > Loading: * > > > > TFTP error: 'Access violation' (2) > > > > Not retrying... > > > > => ping 10.0.2.2 > > > > ethernet@100900fc: PHY present at 0 > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > Using ethernet@100900fc device > > > > host 10.0.2.2 is alive > > > > => > > > > ethernet@100900fc: PHY present at 0 > > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > > Using ethernet@100900fc device > > > > host 10.0.2.2 is alive > > > > => qemu-system-riscv64: terminating on signal 2 > > > > > > > > > > I have always been using "qemu-system-riscv64 -nographic -M sifive_u > > > -kernel u-boot" to test U-Boot on qemu risc-v. > > > With above command, I can "ping 10.0.2.2" and get the exact the same > >
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
Hi Anup, On Wed, Dec 19, 2018 at 2:32 PM Anup Patel wrote: > > On Wed, Dec 19, 2018 at 11:02 AM Bin Meng wrote: > > > > Hi Anup, > > > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel wrote: > > > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng wrote: > > > > > > > > Hi Anup, > > > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel wrote: > > > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng wrote: > > > > > > > > > > > > Hi Anup, > > > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > > wrote: > > > > > > > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > > > > > works fine for QEMU sifive_u machince in both M-mode and > > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > > > applied to QEMU sources: > > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to instantiate the > > > > > > MACB? > > > > > > "-device ?" does not give me anything that looks like MACB. Without > > > > > > a > > > > > > proper "-device " parameter, I can boot U-Boot on QEMU sifive_u and > > > > > > see U-Boot driver is probed, but a simple 'ping' test does not work. > > > > > > > > > > Try the following: > > > > > # setenv ipaddr 10.0.2.1 > > > > > # ping 10.0.2.2 > > > > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > > > The above works for me on QEMU. > > > > > > > > My understanding is that we need enable QEMU network via "-netdev " > > > > (either usr, or tap), with a corresponding "-device". I don't know how > > > > to set it up. What's your command line to test this? > > > > > > > > > > "-netdev" or "-device" parameters are not mandatory. By default, virtual > > > NICs are in NAT mode. The QEMU NAT gateway is at IP address > > > 10.0.2.2. We can always ping the NAT gateway when virtual NIC is in > > > NAT mode. > > > > > > Here's how I compile for M-mode: > > > # ARCH=riscv > > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > > # make qemu-riscv64_defconfig > > > # make > > > > > > My U-boot log is as follows: > > > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ qemu-system-riscv64 -M > > > sifive_u -m 256M -display none -serial stdio -kernel ./u-boot > > > > > > > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 +0530) > > > > > > CPU: rv64imafdcsu > > > Model: ucbbar,spike-bare,qemu > > > DRAM: 256 MiB > > > In:uart@10013000 > > > Out: uart@10013000 > > > Err: uart@10013000 > > > Net: > > > Warning: ethernet@100900fc (eth0) using random MAC address - > > > f6:1f:8c:13:83:c0 > > > eth0: ethernet@100900fc > > > Hit any key to stop autoboot: 0 > > > > > > Device 0: unknown device > > > ethernet@100900fc: PHY present at 0 > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > BOOTP broadcast 1 > > > DHCP client bound to address 10.0.2.15 (2 ms) > > > Using ethernet@100900fc device > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > Filename 'boot.scr.uimg'. > > > Load address: 0x8210 > > > Loading: * > > > TFTP error: 'Access violation' (2) > > > Not retrying... > > > ethernet@100900fc: PHY present at 0 > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > BOOTP broadcast 1 > > > DHCP client bound to address 10.0.2.15 (1 ms) > > > Using ethernet@100900fc device > > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > > Filename 'boot.scr.uimg'. > > > Load address: 0x8100 > > > Loading: * > > > TFTP error: 'Access violation' (2) > > > Not retrying... > > > => ping 10.0.2.2 > > > ethernet@100900fc: PHY present at 0 > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > Using ethernet@100900fc device > > > host 10.0.2.2 is alive > > > => > > > ethernet@100900fc: PHY present at 0 > > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > > Using ethernet@100900fc device > > > host 10.0.2.2 is alive > > > => qemu-system-riscv64: terminating on signal 2 > > > > > > > I have always been using "qemu-system-riscv64 -nographic -M sifive_u > > -kernel u-boot" to test U-Boot on qemu risc-v. > > With above command, I can "ping 10.0.2.2" and get the exact the same > > result as yours. > > > > However I wanted to connect the tap interface to the emulated network > > controller for testing, that's why I wanted to use "-device" and > > "-netdev", but I don't know which device string I need to tell QEMU. > > After a bit googleing I got the following page: > > https://forums.xilinx.com/t5/Embedded-Processor-System-Design/Zyn
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
On Wed, Dec 19, 2018 at 11:02 AM Bin Meng wrote: > > Hi Anup, > > On Wed, Dec 19, 2018 at 12:41 PM Anup Patel wrote: > > > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng wrote: > > > > > > Hi Anup, > > > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel wrote: > > > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng wrote: > > > > > > > > > > Hi Anup, > > > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel > > > > > wrote: > > > > > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > > > > works fine for QEMU sifive_u machince in both M-mode and > > > > > > S-mode with some minor fixes. > > > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > > applied to QEMU sources: > > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to instantiate the MACB? > > > > > "-device ?" does not give me anything that looks like MACB. Without a > > > > > proper "-device " parameter, I can boot U-Boot on QEMU sifive_u and > > > > > see U-Boot driver is probed, but a simple 'ping' test does not work. > > > > > > > > Try the following: > > > > # setenv ipaddr 10.0.2.1 > > > > # ping 10.0.2.2 > > > > > > > > > > Yes, I have set up all the required network parameters. > > > > > > > The above works for me on QEMU. > > > > > > My understanding is that we need enable QEMU network via "-netdev " > > > (either usr, or tap), with a corresponding "-device". I don't know how > > > to set it up. What's your command line to test this? > > > > > > > "-netdev" or "-device" parameters are not mandatory. By default, virtual > > NICs are in NAT mode. The QEMU NAT gateway is at IP address > > 10.0.2.2. We can always ping the NAT gateway when virtual NIC is in > > NAT mode. > > > > Here's how I compile for M-mode: > > # ARCH=riscv > > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > > # make qemu-riscv64_defconfig > > # make > > > > My U-boot log is as follows: > > > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ qemu-system-riscv64 -M > > sifive_u -m 256M -display none -serial stdio -kernel ./u-boot > > > > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 +0530) > > > > CPU: rv64imafdcsu > > Model: ucbbar,spike-bare,qemu > > DRAM: 256 MiB > > In:uart@10013000 > > Out: uart@10013000 > > Err: uart@10013000 > > Net: > > Warning: ethernet@100900fc (eth0) using random MAC address - > > f6:1f:8c:13:83:c0 > > eth0: ethernet@100900fc > > Hit any key to stop autoboot: 0 > > > > Device 0: unknown device > > ethernet@100900fc: PHY present at 0 > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > BOOTP broadcast 1 > > DHCP client bound to address 10.0.2.15 (2 ms) > > Using ethernet@100900fc device > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > Filename 'boot.scr.uimg'. > > Load address: 0x8210 > > Loading: * > > TFTP error: 'Access violation' (2) > > Not retrying... > > ethernet@100900fc: PHY present at 0 > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > BOOTP broadcast 1 > > DHCP client bound to address 10.0.2.15 (1 ms) > > Using ethernet@100900fc device > > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > > Filename 'boot.scr.uimg'. > > Load address: 0x8100 > > Loading: * > > TFTP error: 'Access violation' (2) > > Not retrying... > > => ping 10.0.2.2 > > ethernet@100900fc: PHY present at 0 > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > Using ethernet@100900fc device > > host 10.0.2.2 is alive > > => > > ethernet@100900fc: PHY present at 0 > > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > > Using ethernet@100900fc device > > host 10.0.2.2 is alive > > => qemu-system-riscv64: terminating on signal 2 > > > > I have always been using "qemu-system-riscv64 -nographic -M sifive_u > -kernel u-boot" to test U-Boot on qemu risc-v. > With above command, I can "ping 10.0.2.2" and get the exact the same > result as yours. > > However I wanted to connect the tap interface to the emulated network > controller for testing, that's why I wanted to use "-device" and > "-netdev", but I don't know which device string I need to tell QEMU. > After a bit googleing I got the following page: > https://forums.xilinx.com/t5/Embedded-Processor-System-Design/Zynq-QEMU-Network-Issues/td-p/797050 > > From the page it looks that the device should be "-device > cadence_gem", but when I pass it to QEMU I got: > > qemu-system-riscv64: -device cadence_gem,netdev=net0: Parameter > 'driver' expects pluggable device type > > It looks cadence_gem is not a pluggable device. Any ideas? I have mostly tried TAP device
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
Hi Anup, On Wed, Dec 19, 2018 at 12:41 PM Anup Patel wrote: > > On Tue, Dec 18, 2018 at 4:06 PM Bin Meng wrote: > > > > Hi Anup, > > > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel wrote: > > > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng wrote: > > > > > > > > Hi Anup, > > > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel wrote: > > > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > > > works fine for QEMU sifive_u machince in both M-mode and > > > > > S-mode with some minor fixes. > > > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > > > To try on QEMU, please ensure following patches are > > > > > applied to QEMU sources: > > > > > https://patchwork.kernel.org/patch/10729579/ > > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > > > > What "-device " parameter should I tell QEMU to instantiate the MACB? > > > > "-device ?" does not give me anything that looks like MACB. Without a > > > > proper "-device " parameter, I can boot U-Boot on QEMU sifive_u and > > > > see U-Boot driver is probed, but a simple 'ping' test does not work. > > > > > > Try the following: > > > # setenv ipaddr 10.0.2.1 > > > # ping 10.0.2.2 > > > > > > > Yes, I have set up all the required network parameters. > > > > > The above works for me on QEMU. > > > > My understanding is that we need enable QEMU network via "-netdev " > > (either usr, or tap), with a corresponding "-device". I don't know how > > to set it up. What's your command line to test this? > > > > "-netdev" or "-device" parameters are not mandatory. By default, virtual > NICs are in NAT mode. The QEMU NAT gateway is at IP address > 10.0.2.2. We can always ping the NAT gateway when virtual NIC is in > NAT mode. > > Here's how I compile for M-mode: > # ARCH=riscv > # CROSS_COMPILE=riscv64-unknown-linux-gnu- > # make qemu-riscv64_defconfig > # make > > My U-boot log is as follows: > > anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ qemu-system-riscv64 -M > sifive_u -m 256M -display none -serial stdio -kernel ./u-boot > > > U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 +0530) > > CPU: rv64imafdcsu > Model: ucbbar,spike-bare,qemu > DRAM: 256 MiB > In:uart@10013000 > Out: uart@10013000 > Err: uart@10013000 > Net: > Warning: ethernet@100900fc (eth0) using random MAC address - f6:1f:8c:13:83:c0 > eth0: ethernet@100900fc > Hit any key to stop autoboot: 0 > > Device 0: unknown device > ethernet@100900fc: PHY present at 0 > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > BOOTP broadcast 1 > DHCP client bound to address 10.0.2.15 (2 ms) > Using ethernet@100900fc device > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > Filename 'boot.scr.uimg'. > Load address: 0x8210 > Loading: * > TFTP error: 'Access violation' (2) > Not retrying... > ethernet@100900fc: PHY present at 0 > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > BOOTP broadcast 1 > DHCP client bound to address 10.0.2.15 (1 ms) > Using ethernet@100900fc device > TFTP from server 10.0.2.2; our IP address is 10.0.2.15 > Filename 'boot.scr.uimg'. > Load address: 0x8100 > Loading: * > TFTP error: 'Access violation' (2) > Not retrying... > => ping 10.0.2.2 > ethernet@100900fc: PHY present at 0 > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > Using ethernet@100900fc device > host 10.0.2.2 is alive > => > ethernet@100900fc: PHY present at 0 > ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) > Using ethernet@100900fc device > host 10.0.2.2 is alive > => qemu-system-riscv64: terminating on signal 2 > I have always been using "qemu-system-riscv64 -nographic -M sifive_u -kernel u-boot" to test U-Boot on qemu risc-v. With above command, I can "ping 10.0.2.2" and get the exact the same result as yours. However I wanted to connect the tap interface to the emulated network controller for testing, that's why I wanted to use "-device" and "-netdev", but I don't know which device string I need to tell QEMU. After a bit googleing I got the following page: https://forums.xilinx.com/t5/Embedded-Processor-System-Design/Zynq-QEMU-Network-Issues/td-p/797050 From the page it looks that the device should be "-device cadence_gem", but when I pass it to QEMU I got: qemu-system-riscv64: -device cadence_gem,netdev=net0: Parameter 'driver' expects pluggable device type It looks cadence_gem is not a pluggable device. Any ideas? Regards, Bin ___ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
On Tue, Dec 18, 2018 at 4:06 PM Bin Meng wrote: > > Hi Anup, > > On Tue, Dec 18, 2018 at 6:33 PM Anup Patel wrote: > > > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng wrote: > > > > > > Hi Anup, > > > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel wrote: > > > > > > > > This patchset enables Cadance MACB ethernet driver for > > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > > works fine for QEMU sifive_u machince in both M-mode and > > > > S-mode with some minor fixes. > > > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > > > To try on QEMU, please ensure following patches are > > > > applied to QEMU sources: > > > > https://patchwork.kernel.org/patch/10729579/ > > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > > > > What "-device " parameter should I tell QEMU to instantiate the MACB? > > > "-device ?" does not give me anything that looks like MACB. Without a > > > proper "-device " parameter, I can boot U-Boot on QEMU sifive_u and > > > see U-Boot driver is probed, but a simple 'ping' test does not work. > > > > Try the following: > > # setenv ipaddr 10.0.2.1 > > # ping 10.0.2.2 > > > > Yes, I have set up all the required network parameters. > > > The above works for me on QEMU. > > My understanding is that we need enable QEMU network via "-netdev " > (either usr, or tap), with a corresponding "-device". I don't know how > to set it up. What's your command line to test this? > "-netdev" or "-device" parameters are not mandatory. By default, virtual NICs are in NAT mode. The QEMU NAT gateway is at IP address 10.0.2.2. We can always ping the NAT gateway when virtual NIC is in NAT mode. Here's how I compile for M-mode: # ARCH=riscv # CROSS_COMPILE=riscv64-unknown-linux-gnu- # make qemu-riscv64_defconfig # make My U-boot log is as follows: anup@anup-ubuntu64:~/Work/riscv-test/u-boot$ qemu-system-riscv64 -M sifive_u -m 256M -display none -serial stdio -kernel ./u-boot U-Boot 2019.01-rc1-00948-ge6b3cdafd0 (Dec 19 2018 - 10:05:50 +0530) CPU: rv64imafdcsu Model: ucbbar,spike-bare,qemu DRAM: 256 MiB In:uart@10013000 Out: uart@10013000 Err: uart@10013000 Net: Warning: ethernet@100900fc (eth0) using random MAC address - f6:1f:8c:13:83:c0 eth0: ethernet@100900fc Hit any key to stop autoboot: 0 Device 0: unknown device ethernet@100900fc: PHY present at 0 ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) BOOTP broadcast 1 DHCP client bound to address 10.0.2.15 (2 ms) Using ethernet@100900fc device TFTP from server 10.0.2.2; our IP address is 10.0.2.15 Filename 'boot.scr.uimg'. Load address: 0x8210 Loading: * TFTP error: 'Access violation' (2) Not retrying... ethernet@100900fc: PHY present at 0 ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) BOOTP broadcast 1 DHCP client bound to address 10.0.2.15 (1 ms) Using ethernet@100900fc device TFTP from server 10.0.2.2; our IP address is 10.0.2.15 Filename 'boot.scr.uimg'. Load address: 0x8100 Loading: * TFTP error: 'Access violation' (2) Not retrying... => ping 10.0.2.2 ethernet@100900fc: PHY present at 0 ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) Using ethernet@100900fc device host 10.0.2.2 is alive => ethernet@100900fc: PHY present at 0 ethernet@100900fc: link up, 100Mbps full-duplex (lpa: 0xcde1) Using ethernet@100900fc device host 10.0.2.2 is alive => qemu-system-riscv64: terminating on signal 2 Regards, Anup ___ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
Hi Anup, On Tue, Dec 18, 2018 at 6:33 PM Anup Patel wrote: > > On Tue, Dec 18, 2018 at 3:21 PM Bin Meng wrote: > > > > Hi Anup, > > > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel wrote: > > > > > > This patchset enables Cadance MACB ethernet driver for > > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > > works fine for QEMU sifive_u machince in both M-mode and > > > S-mode with some minor fixes. > > > > > > The patches are based upon latest RISC-V U-Boot tree > > > (git://git.denx.de/u-boot-riscv.git) at commit id > > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > > > To try on QEMU, please ensure following patches are > > > applied to QEMU sources: > > > https://patchwork.kernel.org/patch/10729579/ > > > https://patchwork.kernel.org/patch/10729581/ > > > > > > > What "-device " parameter should I tell QEMU to instantiate the MACB? > > "-device ?" does not give me anything that looks like MACB. Without a > > proper "-device " parameter, I can boot U-Boot on QEMU sifive_u and > > see U-Boot driver is probed, but a simple 'ping' test does not work. > > Try the following: > # setenv ipaddr 10.0.2.1 > # ping 10.0.2.2 > Yes, I have set up all the required network parameters. > The above works for me on QEMU. My understanding is that we need enable QEMU network via "-netdev " (either usr, or tap), with a corresponding "-device". I don't know how to set it up. What's your command line to test this? Regards, Bin ___ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
On Tue, Dec 18, 2018 at 3:21 PM Bin Meng wrote: > > Hi Anup, > > On Mon, Dec 17, 2018 at 7:51 PM Anup Patel wrote: > > > > This patchset enables Cadance MACB ethernet driver for > > QEMU sifive_u machine. The Cadance MACB ethernet driver > > works fine for QEMU sifive_u machince in both M-mode and > > S-mode with some minor fixes. > > > > The patches are based upon latest RISC-V U-Boot tree > > (git://git.denx.de/u-boot-riscv.git) at commit id > > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > > > To try on QEMU, please ensure following patches are > > applied to QEMU sources: > > https://patchwork.kernel.org/patch/10729579/ > > https://patchwork.kernel.org/patch/10729581/ > > > > What "-device " parameter should I tell QEMU to instantiate the MACB? > "-device ?" does not give me anything that looks like MACB. Without a > proper "-device " parameter, I can boot U-Boot on QEMU sifive_u and > see U-Boot driver is probed, but a simple 'ping' test does not work. Try the following: # setenv ipaddr 10.0.2.1 # ping 10.0.2.2 The above works for me on QEMU. Regards, Anup ___ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
Re: [U-Boot] [PATCH 0/3] Ethernet support for QEMU sifive_u machine
Hi Anup, On Mon, Dec 17, 2018 at 7:51 PM Anup Patel wrote: > > This patchset enables Cadance MACB ethernet driver for > QEMU sifive_u machine. The Cadance MACB ethernet driver > works fine for QEMU sifive_u machince in both M-mode and > S-mode with some minor fixes. > > The patches are based upon latest RISC-V U-Boot tree > (git://git.denx.de/u-boot-riscv.git) at commit id > 9deb8d2fcd13d4a40a4e63c396fe4376af46efac > > To try on QEMU, please ensure following patches are > applied to QEMU sources: > https://patchwork.kernel.org/patch/10729579/ > https://patchwork.kernel.org/patch/10729581/ > What "-device " parameter should I tell QEMU to instantiate the MACB? "-device ?" does not give me anything that looks like MACB. Without a proper "-device " parameter, I can boot U-Boot on QEMU sifive_u and see U-Boot driver is probed, but a simple 'ping' test does not work. > Anup Patel (3): > riscv: Add asm/dma-mapping.h for DMA mappings > net: macb: Fix clk API usage for RISC-V systems > riscv: qemu: Imply MACB ethernet for emulation > > arch/riscv/include/asm/dma-mapping.h | 37 > board/emulation/qemu-riscv/Kconfig | 4 +++ > drivers/net/macb.c | 4 ++- > 3 files changed, 44 insertions(+), 1 deletion(-) > create mode 100644 arch/riscv/include/asm/dma-mapping.h > > -- Regards, Bin ___ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot