hello, all of users:
sorry, resend it again for clarifying the message. I have implemented cha_ss7
in china. initially, the
chan_ss7 can not support the call group. i modify the code.
now the problem is that, both sides can hear the ring, but i
can not hear the voice from each other.
i think
hello,
I try to open the debug to compile dahdi with wcb4xxp,
=base.c
#ifdef DEBUG_LOWLEVEL_REGS
if (unlikely(DBG_REGS))
drv_dbg(b4-dev, read 0x%02x from 0x%p\n, ret, b4-addr +
reg);
#endif
if
hello, all of users:
after dig the code, i found that dahdi wcb4xxp is only for digium B410P. it has
VPM hardware based echo cancellation, which Junghans and openvox bri cards do
not have. anyone can tell me how to disable the ec_write methond to support
other HFC BRI cards?
regards!
zhu
hello:
thanks for Tzafrir Cohen for dahdi testing.
I installed dahdi-2.1-r3c svn code and asterisk1-6
for testing OpenVox B400P and junghans card. i fund that there is bug (i think)
to dectect NT or TE mode. actually on the board,
i set it as TE mode, but after start wcb4xxp, but
it show the
hello, users:
I tried to change to hardhdlc in system. but i still can not make calls. the
port 4 led still can be be on.
=system.conf==
# Autogenerated by ./dahdi_genconf on Wed Nov 12 19:22:36 2008 -- do not hand
edit
# Dahdi Configuration File
#
# This file is parsed
hello:
i want to test the g729 with asterisk. my scenario is sipp(ulaw)-asterisk1
with g729-asterisk2 with g729.
I want to test g729 module with asterisk-1.4.21, when i make calls from
asterisk 1 to asterisk 2, the asterisk 1 always send ulaw to asterisk 2. my sip
in asterisk 1 is with codec
hello, all of users:
i want to test the dahdi with asterisk-1.6, but there is no much source for
this new project. the only information i got is from voip-info. my problem is
that, i can not enable the chan_zap, therefore i do not have chan_zap.so in
asterisk/modules, i can not remane it to
hello, all of users:
i have a problem with loading chan_dahdi.so. when i start asterisk, it always
reports the can not open channel 1 in ...
here is my setting: in etc/system/dahdi.conf:
# Global data
fxsks=1
fxsks=2
fxoks=3
fxoks=4
loadzone= us
defaultzone = us
-
hello, all of asteriskers:
i am using tdm400P in my office. i tested that TDMF generated by asterisk is so
bad. the sound is very soft and quality is so bad. i am using asterisk 1.2.18.
most of time, the # key can not be detected correctly. Does anyone has that
problem?
please give me a hit
hello, asteriskers:
i compile asterisk 1.2.18 in arm-linux. i got this error :dlfcn.c:40:
mach-o/dyld.h: No such file or directory. i check the /usr/include dir, there
is no mach-o dir and dyld.h file in /usr/include. i think i am missing
somethings in the cross-compile tools. Does nayone know
hello, James FitzGibbon:
thank you for your help. i am very new to arm-linux and embedded linux. i think
what you said is right. i am not very sure the steps i taken are correct. i
post it here and please give me some help. it might be help other arm-linux
users too. i installed all necessary
hello, asteriskers:
I compiled asterisk under arm-linux. i am using asterisk 1.4.2. i can run
./configure and menuselect with embedded modules. but running make comes out
errors:
ranlib libmxml.a
make[3]: Leaving directory `/usr/src/asterisk-1.4.2/menuselect/mxml'
cc -Wall -o menuselect.o -g -c
12 matches
Mail list logo
