Re: [ath9k-devel] [PATCH 4.9.0-rc5] AR9300 calibration problems with antenna selected

On 21/11/16 14:54, Krzysztof Hałasa wrote: > miaoq...@codeaurora.org writes: > >>> rmmod ath9k >>> modprobe ath9k >>> iw dev wlan0 set type ibss >>> iw phy phyX set antenna 2 >> >> 2 is a bad mask. We use bitmap, the valid masks are 1, 3, 7. > > Thanks for your response. > > I have two antenna

Re: [ath9k-devel] What is the expected throughput of ath9k with 20Mhz channel bandwidth?

ee how much it can go. I expected 2 > streams 20Mhz to get around 90Mbps. > > Thanks, > Dat > > My AR9342 is 2 streams > > On Wed, 29 Jun 2016 at 19:33 Matthias May <matthias@neratec.com > <mailto:matthias@neratec.com>> wrote: > > On 2

Re: [ath9k-devel] What is the expected throughput of ath9k with 20Mhz channel bandwidth?

On 29/06/16 13:01, Le Tran Dat wrote: > Hi, > > I am testing AR9342 Throughput with 20Mhz channel bandwidth, using > OpenWRT/LEDE firmware. > However, the throughput result is quite low. About 65Mbps to 70Mbps > while the bitrate is 144Mbps. > While testing I monitor the CPU usage and it's still

Re: [ath9k-devel] [OpenWrt-Devel] ath9k: Deaf QCA9558 when setting rxchainmask

2. Best regards Matthias May -- Matthias May Software Engineer Neratec Solutions AG Postfach 83, CH-8608 Bubikon, Switzerland Direct: +41 55 253 2074 Office: +41 55 253 2000 Fax:+41 55 253 2070 email: matthias@neratec.com Web: www.neratec.com Nov 18 13:39:45 CHD500279 kernel

Re: [ath9k-devel] [OpenWrt-Devel] ath9k: Deaf QCA9558 when setting rxchainmask

On 18/11/13 14:12, Sujith Manoharan wrote: Matthias May wrote: I'm in the position where i want to use a 9390 as 2x2 instead of 3x3. I use backports-3.12-1. I've set the rx and tx mask in eeprom to 0x5. Every 30 seconds there is a short disconnect. Enabling some logging in echo 0x050C

Re: [ath9k-devel] AR9580/90

priority scan. Device supports scan flush. Device supports AP scan. -- Matthias May Software Engineer Neratec Solutions AG Postfach 83, CH-8608 Bubikon, Switzerland Direct: +41 55 253 2074 Office: +41 55 253 2000 Fax:+41 55 253 2070 email: matthias@neratec.com Web: www.neratec.com

Re: [ath9k-devel] How to block a concrete channel?

Don't forget to adjust the ATH9K_NUM_CHANNELS in ./drivers/net/wireless/ath/ath9k/hw.h regards -- Matthias May Software Engineer Neratec Solutions AG Postfach 83, CH-8608 Bubikon, Switzerland Direct: +41 55 253 2074 Office: +41 55 253 2000 Fax:+41 55 253 2070 email: matthias@neratec.com

[ath9k-devel] [PATCH] Improve passive scanning: check not only for proberesp_ies but also for beacon_ies

-by: Matthias May matthias@neratec.com --- net/mac80211/mlme.c |2 +- 1 files changed, 1 insertions(+), 1 deletions(-) diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c index d2a4f78..fae5f9c 100644 --- a/net/mac80211/mlme.c +++ b/net/mac80211/mlme.c @@ -2817,7 +2817,7 @@ static int