Hello Gerald,
I removed the resistor and placed a jumper between J3 1-2 attached a sata
drive with a new debian image written via dd and am unable to boot. I'm
getting a blank screen and the power LED comes on and the LED between the
power connector and the RAM illuminates for just a few seco
Hello,
I just tried to set up the X15 for a direct boot from eSATA. I purchaed an
external SATA drive and eSATA cable and wrote the latest X-15 debian image
to it via dd. I removed the R444 and placed a jumper from J3 1-2 and
attempted a boot - FAILED. The power LED illuminates. The LED betw
Bug Report
Hardware BargleBone Black(BBB)
OS Debian pre-installed on eMMC
Problem Type: Hardware Logitech Unifying Receiver not recognized by OS.
Cannot get wireless keyboard & mouse to connect to OS from Logitech
Unifying Receiver.
Beagle Bone desktop appears but BeagleBone Black has only 1
I followed the steps including going to the maker.io on digikey. I have
logged into the pocket but not under root that didn't seem to work. I
didn't have the password. But I did log in under debian. But I'm having
trouble getting the pocket to see the internet. no ping. I think the
instru
I doubt you have fried it, but sounds like the SW is not writing to a register
that keeps the board active, something that was put in place due to a silicon
bug in the HW. I suspect you do not have the correct UBoot or it is not
reading the SATA correctly. It will time out and then shutdown.
G
Same answer as before.
Gerald
From: beagleboard@googlegroups.com [mailto:beagleboard@googlegroups.com] On
Behalf Of mab.mobile...@gmail.com
Sent: Saturday, September 30, 2017 8:52 PM
To: BeagleBoard
Subject: [beagleboard] X15 attempt at SATA boot failed
Hello,
I just tried to set up the X15
Sounds like I may missing something. I'm assuming u-boot would be on the
debian image written to the SATA drive via dd? Do I need to install this
separetly? The Beagle Bone Black is pretty straight foreward with good
documentation. The X15 is not. Are there any more detailed instructions
on-lin
All I can do is say what the symptoms you are seeing could be caused by, not
setting a register in the PMIC on boot up. I cannot answer as to what the SW
is or is not doing in your installation.
Gerald
From: beagleboard@googlegroups.com [mailto:beagleboard@googlegroups.com] On
Behalf Of mab.m
On Sun, Oct 1, 2017 at 10:05 AM, wrote:
> Sounds like I may missing something. I'm assuming u-boot would be on the
> debian image written to the SATA drive via dd?
Sure, if you "patch" u-boot and "build" it for that situation, it
would work. The current U-Boot binary we ship for the debian imag
Robert:
OK. I found a Samtec part that will probably fit, but will need to get some
samples and try it.
The part numbers are already set up in Digikey's system, but not stocked,
quoting large minimum quantities and three week delivery.
Can you get samples from Samtec? Or, I can call in a favo
On Sun, Oct 1, 2017 at 4:51 PM, Graham wrote:
> Robert:
>
> OK. I found a Samtec part that will probably fit, but will need to get
> some samples and try it.
>
> The part numbers are already set up in Digikey's system, but not stocked,
> quoting large minimum quantities and three week delivery.
>
https://www.linux.com/news/event/open-source-summit-na/2017/3/latest-linux-maker-boards-gamble-diversity
and...
http://linuxgizmos.com/open-source-comm-protocol-for-uavs-supported-with-beaglebone-based-modem/
Cool!
Seth
--
For more options, visit http://beagleboard.org/discuss
---
You receiv
12 matches
Mail list logo
