Yes, it's work.
Thank you.
On Thu, Jan 18, 2018 at 6:53 PM, Shimon Filtzer wrote:
> Thank you.
> I try this way. Kernel rebuild takes a time
>
> On Tue, Jan 16, 2018 at 7:56 PM, Robert Nelson
> wrote:
>
>> On Tue, Jan 16, 2018 at 10:57 AM, wrote:
>> >
I checked twice...
On Sun, Jan 21, 2018 at 10:11 AM, Shimon Filtzer wrote:
> Yes, it's correct.
> I tried overlay_addr4=/lib/firmware/BB-I2C2-00A0.dtbo
> and overlay_addr0=/lib/firmware/BB-I2C2-00A0.dtbo
>
> May be exists some additional way?
> Regards
>
> четверг
Yes, it's correct.
I tried overlay_addr4=/lib/firmware/BB-I2C2-00A0.dtbo
and overlay_addr0=/lib/firmware/BB-I2C2-00A0.dtbo
May be exists some additional way?
Regards
четверг, 18 января 2018 г., 19:59:17 UTC+2 пользователь RobertCNelson
написал:
>
> On Thu, Jan 18, 2018 at 11:52
PM, Robert Nelson
wrote:
> On Thu, Jan 18, 2018 at 11:52 AM, Shimon Filtzer
> wrote:
> > Ok,
> > On P9-19/P9-20, i2c2?
> > I, tried i2cdetect -r 2, and my slave doesn't exist.
> > May be I need some additional overlay/definition?
>
> Did you load it?
>
Ok,
On P9-19/P9-20, i2c2?
I, tried i2cdetect -r 2, and my slave doesn't exist.
May be I need some additional overlay/definition?
On Thu, Jan 18, 2018 at 7:42 PM, Robert Nelson
wrote:
> On Thu, Jan 18, 2018 at 11:37 AM, Shimon Filtzer
> wrote:
> > uboot_overlay_addr4=/lib/firm
uboot_overlay_addr4=/lib/firmware/BB-I2C1-00A0.dtbo
i2c1
P9-19
P9-20
On Thu, Jan 18, 2018 at 7:17 PM, Robert Nelson
wrote:
> On Thu, Jan 18, 2018 at 11:15 AM, Shimon Filtzer
> wrote:
> > After Upgrade Kernel from 3.8.13 -> 4.9, and i2c1 overlay configuration
> in
> >
After Upgrade Kernel from 3.8.13 -> 4.9, and i2c1 overlay configuration in
uEnv.txt,
I tried to find slave i2c device without success.
In /dev, i2c-1 exists. When I check pin-config, I see correct pin
configuration.
Execution i2cdetect, can not find anything.
When I run on same BBB card, kernel 3
Thank you.
I try this way. Kernel rebuild takes a time
On Tue, Jan 16, 2018 at 7:56 PM, Robert Nelson
wrote:
> On Tue, Jan 16, 2018 at 10:57 AM, wrote:
> > We got new BeagleBone Black cards, and when try to flash image I got an
> > error,
> > Error: [/dev/mmcblk1] does not exist.
> >
> > I sur
Hello, guys!
For my application I need, that pin P8-13(GPIO23), will get output high
level as soon as possible. As I understand, I need to change both uboot and
kernel. (is it correct?)
But I can not find some manual for these changes.
Any help?
Thank you!
--
For more options, visit http://bea
