I'm at the same place did you ever find a solution? On Sunday, May 12, 2013 at 6:24:36 AM UTC-7, Gerald wrote: > > That is not the latest version. Follow the link on the card that came in > the box with the board as instructed, > > http://circuitco.com/support/index.php?title=BeagleBoneBlack > > You will end up here after following the links in the table of contents. > > > http://circuitco.com/support/index.php?title=Updating_The_Software#Flashing_the_eMMC > > Gerald > > > > On Sun, May 12, 2013 at 5:22 AM, Jinserk Baik <jinser...@gmail.com > <javascript:>> wrote: > >> Hello, I'm newbie for BBB, and I just want to update eMMC image >> downloaded from the official website http://beagleboard.org/latest-images >> . >> >> But after I inserted the copied microSD card and power on with the S2 key >> hold down, nothing gonna occur. >> Here is the serial console message. >> What's wrong? >> >> >> >> U-Boot SPL 2013.04-dirty (Apr 26 2013 - 07:32:17) >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Host mode controller at 47401800 using PIO, IRQ 0 >> OMAP SD/MMC: 0 >> reading u-boot.img >> reading u-boot.img >> >> >> U-Boot 2013.04-dirty (Apr 26 2013 - 07:32:17) >> >> I2C: ready >> DRAM: 512 MiB >> WARNING: Caches not enabled >> NAND: No NAND device found!!! >> 0 MiB >> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 >> *** Warning - readenv() failed, using default environment >> >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Host mode controller at 47401800 using PIO, IRQ 0 >> Net: <ethaddr> not set. Validating first E-fuse MAC >> Phy not found >> PHY reset timed out >> cpsw, usb_ether >> Hit any key to stop autoboot: 0 >> gpio: pin 53 (gpio 53) value is 1 >> mmc0 is current device >> micro SD card found >> mmc0 is current device >> gpio: pin 54 (gpio 54) value is 1 >> SD/MMC found on device 0 >> reading uEnv.txt >> 14 bytes read in 3 ms (3.9 KiB/s) >> Loaded environment from uEnv.txt >> Importing environment from mmc ... >> gpio: pin 55 (gpio 55) value is 1 >> 4484848 bytes read in 767 ms (5.6 MiB/s) >> gpio: pin 56 (gpio 56) value is 1 >> 22492 bytes read in 30 ms (731.4 KiB/s) >> Booting from mmc ... >> ## Booting kernel from Legacy Image at 80007fc0 ... >> Image Name: Angstrom/3.8.3/beaglebone >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 4484784 Bytes = 4.3 MiB >> Load Address: 80008000 >> Entry Point: 80008000 >> Verifying Checksum ... OK >> ## Flattened Device Tree blob at 80f80000 >> Booting using the fdt blob at 0x80f80000 >> XIP Kernel Image ... OK >> OK >> Using Device Tree in place at 80f80000, end 80f887db >> >> Starting kernel ... >> >> Uncompressing Linux... done, booting the kernel. >> [ 0.105975] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 >> invalid phandle >> [ 0.222212] omap2_mbox_probe: platform not supported >> [ 0.471626] tps65217-bl tps65217-bl: no platform data provided >> [ 0.555486] bone-capemgr bone_capemgr.8: slot #0: No cape found >> [ 0.592592] bone-capemgr bone_capemgr.8: slot #1: No cape found >> [ 0.629701] bone-capemgr bone_capemgr.8: slot #2: No cape found >> [ 0.666809] bone-capemgr bone_capemgr.8: slot #3: No cape found >> [ 0.751300] pinctrl-single 44e10800.pinmux: pin 44e1080c already >> requested by mmc.4; cannot claim for gpio-leds.7 >> [ 0.762157] pinctrl-single 44e10800.pinmux: pin-3 (gpio-leds.7) status >> -22 >> [ 0.769403] pinctrl-single 44e10800.pinmux: could not request pin 3 on >> device pinctrl-single >> [ 5.711829] libphy: PHY 4a101000.mdio:00 not found >> [ 5.716878] net eth0: phy 4a101000.mdio:00 not found on slave 0 >> [ 5.723093] libphy: PHY 4a101000.mdio:01 not found >> [ 5.728120] net eth0: phy 4a101000.mdio:01 not found on slave 1 >> >> .---O---. >> | | .-. o o >> | | |-----.-----.-----.| | .----..-----.-----. >> | | | __ | ---'| '--.| .-'| | | >> | | | | | |--- || --'| | | ' | | | | >> '---'---'--'--'--. |-----''----''--' '-----'-'-'-' >> -' | >> '---' >> >> The Angstrom Distribution beaglebone ttyO0 >> >> Angstrom v2012.12 - Kernel 3.8.3 >> >> beaglebone login: systemd-fsck[83]: eMMC-Flasher: clean, 12711/218592 >> files, 170358/873534 blocks >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to beagleboard...@googlegroups.com <javascript:>. >> For more options, visit https://groups.google.com/groups/opt_out. >> >> >> > > > > -- > Gerald > > ger...@beagleboard.org <javascript:> > g-co...@ti.com <javascript:> > http://beagleboard.org/ > http://circuitco.com/support/ >
-- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.
