HiAll
A Close Look at Asphalt Roofs
Roofing installation is a big job, and not just in the size of the project.
As the number one weather barrier of the home, the roof is one area where
you
do not want any mistakes. A first-time roof installation is best left to an
experienced professional. The pros are trained how to properly construct the
roof deck, how to install underlayment, drip edges and flashings and how to
correctly apply the shingles. Roofing is also hazardous work, leading most
manufacturers to specify that their product only be installed by a trained
professional.
However, do-it-yourselfers who aren't afraid of heights or hard work have
been known to tackle a re-roofing project first-hand. While asphalt shingles
are
designed for decades of low-maintenance performance, after about 20 years
the roof should be inspected annually, and eventually it will need to be
re-shingled.
When that time comes, a DIY re-roofing project can save about 50 percent on
the cost of the job.
Assessing the Roof
Asphalt shingles are the most widely used roofing material in residential
construction, accounting for roughly 80 percent of the market. Today's
asphalt
roofing greatly outperforms the shingles available 30 years ago. Season
after season, asphalt roofing will protect you and your family, and provide
a terrific
value for your roofing investment. Asphalt costs significantly less than
higher-priced rivals (including tile, wood, cedar, slate and metal) and
requires
very little maintenance over the years. And shingles come in a wide range of
colors that allow you to choose a tone that complements the exterior colors
of your house.
After a couple of decades you'll need to inspect your roof for signs of
deterioration. The most obvious perpetrator is a roof leak, indicated by
water stains
or wet areas in the attic. In some cases these can be patched, but in the
case of a serious leak, it's time to re-roof. Also, excessive mineral
granules
or bare spots on the shingles are evidence that the asphalt is deteriorating
and should be replaced. Shingles also tend to crack or curl from sun
exposure,
and wind can blow them off the roof-a sure sign that a repair is in order.
In some cases you can shingle right over a pre-shingled roof (see Side Note
at bottom). However, you have to consider weight, smoothness of the existing
roof, local codes and the capability for fasteners to hold the shingles
securely. Fasteners must be long enough to completely penetrate at least 3/4
inch
into the solid roof deck when hammered flush with the shingle. So if the
roof has already been re-shingled in the past, then there will likely be too
many
layers for the fasteners to hold properly. In many cases, two layers of
shingles is the maximum.
If the roof is in bad shape or too many shingle layers are in place, then
the roof requires a tear-off. A hammer and pry bar are used to loosen the
nails,
and the shingles are removed with a flat shovel. Tearing off roof shingles
is hard work, but it does provide the opportunity to thoroughly repair the
roof
and update your material from standard three-tab shingles to attractive
asphalt architectural shingles that can raise the overall value of the home.
Architectural
shingles last longer and look a little different. Instead of slots in the
shingle, the architectural types get their texture from tabs that are
laminated
onto the shingle. This provides extra thickness and, in turn, more
durability. For the most part, architectural shingles install similarly to
the three-tab
type, but always check your manufacturer's instructions for any recommended
variations in the installation method.
Getting Started
The first step in a roof project is to check the weather report. Ideally,
you don't want any showers heading your way for the next three days.
However,
as Mother Nature is known to be unpredictable, have a couple of tarps on
hand in case of rain.
If you're re-roofing, first nail down all loose shingles and replace any
that are missing. Or, with a tear-off, make all the necessary repairs to the
roof
sheathing, underlayment, wood trim and flashing. The roof surface must be
dry, cleaned and properly prepared before roofing. For more information on
proper
sheathing and flashing techniques, check out the variety of online roofing
articles at
www.extremehowto.com
and
www.apawood.org.
Appropriately enough, shingling a roof starts at the roof edge with what is
called a "starter strip." At the lower end of a standard shingle are three
tabs
separated by slots about 3/8-inch wide. The starter strip prevents rainwater
from flowing through these slots and onto the roofing underlayment. To
create
the starter strip, first cut off the tabs of the first shingle and discard
them. Cut from the back side of the shingle when possible to avoid dulling
the
knife blade. Then cut 6 inches off the first starter-course shingle and
apply the rest of it on the lower corner of the roof, with the cut edge
overlapping
the eaves and gutter apron. The shingle should overlap rakes and eaves by
1/2 inch if using a drip edge. If not using a drip edge, make the overhang
3/4
inch. Continue applying full-length starter-course shingles along the eaves.
Shingle All the Way
With the starter strip complete, you're ready for the first course. Apply a
full shingle at the lower roof corner on top of the starter course. The tabs
of the shingle should be flush with the edges of the starter course. This
method seals the lower edge of the roof to help prevent the edge shingles
from
lifting in high winds.
To fasten the shingles, apply four nails through the tabs just below the
sealant line, 1 inch from each edge and just above each slot. In areas
exposed
to high winds, six nails can be used (two nails flanking the top of each
slot). Use 11- or 12-guage corrosion-resistant roofing nails at least 1-inch
long
with at least 3/8-inch heads. Make sure the nails are driven straight, not
overdriven or under-driven. Check your manufacturer's instructions for
specific
nailing requirements.
In steep slope applications (over 21/12), asphalt roofing cement should be
used in conjunction with nails. One inch of roofing cement should be applied
beneath each corner of the tabs. However, working on a steep slope can be
very dangerous and require special scaffolding; such projects are best left
to
the professionals.
Once the first shingle is in place, snap a chalk line from the top of the
shingle to the opposite edge of the roof. Then move to the first shingle of
the
second course. This helps align the shingles, and moving up rather than out
means you don't have to journey across the roof with each successive
shingle.
Cut 6 inches off the first second-course shingle. Align the bottom edge of
the shingle with the top of the tabs of the first shingle. Nail it in place.
With those shingles in place, move to the third course. Cut 12 inches off
the first third-course shingle. Align the bottom edge with the top of the
slots
in the second-course shingle, and nail it home. Continue progressing up the
roof, nailing the first shingle of each course 6 inches narrower than the
one
beneath it (see diagram). After the sixth course, you will begin with
another full shingle aligned with the edge of the roof.
After you've worked up to the roof ridge, return to the lower edge of the
roof. Butt a full-length shingle next to the first-course shingle and nail
in
place. Continue back up the roof, nailing a full-length shingle against each
of the starting shingles that are already in place. Follow this shingling
procedure to complete the field of the roof. All the shingles are
full-length except the ones at the edge of the roof.
At the edge of the roof, use a straight edge to cut the shingles to overlap
the rake by no more than 3/4 inch. On hips and ridges, trim the shingles
flush
with the centerline.
Hips, Ridges and Valleys
Hips and ridges must be covered by 12-inch ridge caps. Some companies offer
special ridge cap shingles. Check to see if they're available for the
shingles
you're installing. If not, then make the caps from regular 36-inch shingles
cut into thirds, separated at the tabs. Cut the sealant ends of the tabs so
they taper to about 10 inches. To install, snap a chalk line on each side of
the ridge or hip, 6 inches from the center line. Start with the first cap
at the end of the ridge opposite from the prevailing wind direction. Bend
the cap over the ridge along the center line. Fasten with two nails on each
cap,
just above the sealing tab and 1 inch from each edge. Overlap the caps by 1
inch, leaving a 5-inch tab exposed. Do not expose the fasteners.
As for valleys, in some cases a non-corrosive prefabricated metal flashing
is installed, and the shingles are cut back to allow drainage. This is
called
an open valley.
A closed cut valley is installed over a heavy-duty valley liner or metal
roll flashing. Shingles are then overlapped. (Do not nail shingles within 6
inches
of the centerline.) Then a straight line is cut through the top layer of
shingles 2 inches away from the centerline of the valley. The 2-inch offset
prevents
the majority of the water runoff from flowing directly over the seam. When
cutting, use flashing beneath the top layer to prevent cutting the layer
below.
For more information on asphalt roofing, visit the Asphalt Roofing
Manufacturers Association online at
www.asphaltroofing.org
or call (202) 207-0917.
Side Note #1
Shingling Over an Existing Roof
The process of re-shingling or re-roofing is only slightly different from
installing a new roof. On a new roof the underlayment is smooth, lying flat
on
the roof sheathing. On an existing roof, the surface is not smooth because
of the shingles, which are installed in stair-like layers. Since asphalt is
a plastic material, the shingles will conform to the surface of whatever is
beneath them. To compensate for the lack of flatness, simply fill in the
first
step of the shingles. Cut off the top of the shingles lengthwise to fit
perfectly over the bottom row of tabs on the existing roof and nail them in
place.
Start with a shingle cut 6 inches short, so the ends won't align with the
ends of the existing shingles. Complete the bottom row in this manner using
full-length
"filler" shingles. Each new row of shingles fills in the gap for the row to
follow. From here onward, shingle as you would a normal roof, covering the
first course with full-width shingles.
Side Note #2
Ten Tips for Successful Roofing
1. Proper flashing around chimneys, vent pipes, dormers and other
obstructions is critically important to avoid leaks. If you're unsure how to
do
this, then leave it to a professional.
2. In roofing, properly installed underlayment is also critical for a
good roof. It comes in 15- or 30-pound roofing felt that's soaked in
asphalt.
Use felt specified by the shingle manufacturer. It is installed beginning at
the bottom of the roof. Each strip overlays the strip below by a few inches,
so flowing water is directed over the seam and not into it.
3. When cutting shingles, it's easiest to use a roofing knife with a
hooked blade.
4. Don't attempt to shingle in extremely cold or hot weather. In cold
weather, shingles can become brittle and break. In hot weather you can scar
the shingles with your feet.
5. The sealing of the shingles may be delayed by cooler weather or by
the presence of airborne dust. If the shingles don't seal, it may be
necessary
to hand seal.
6. Installation of laminated architectural shingles may vary from the
6-inch layout discrepancy shown in this article. They may need to be stepped
off 7 or 8 inches. Check the manufacturer's instructions for recommended
installation methods.
7. Save the trimmed pieces of stepped-off shingles to fill in at rakes
and valleys.
8. Use all shingles from one bundle before moving to the next bundle.
This will help the colors blend on a finished roof.
9. If possible, have the roofing supplier place the shingle bundles on
the roof so you don't have to carry all the shingles up a ladder.
10. Always check with local building codes that may specify the rating
of shingles and other construction requirements that may apply to your area.
Side Note #3
Shingle Safely
The right gear is essential for safe roofing. The roof surface is sloped and
it can be slick. Walk on the roof as little as possible and wear soft,
rubber-soled
shoes with ankle supports to resist slips. A wet roof can be treacherous, so
stay off it. And steep slopes are best left to the pros. Never work on the
roof during the threat of lightning. Stay away from power lines and keep the
roof clean of debris or other obstacles.
It is recommended to use a safety harness with a fall-arrest rope. Special
roof scaffolds can provide a flat surface to support you and your materials.
Use a metal ladder bracket to hook your ladder to the roof. Make sure your
ladder is strong, sturdy and free from cracks or other weaknesses. Keep the
base on firm, level ground. Keep your hips between the ladder rails, and
never reach out to work; move the ladder instead. Only one person should
ever
be on a ladder at once. Never stand on the top two rungs of the ladder. For
roof work, at least two rungs should extend above the eaves. Rather than
carrying
tools and materials up a ladder, pull them up in a bucket.
To listen to the show archives go to link
http://acbradio.org/handyman.html
or
ftp://ftp.acbradio.org/acbradio-archives/handyman/
The Pod Cast address for the Blind Handy Man Show is.
http://www.acbradio.org/news/xml/podcast.php?pgm=saturday
The Pod Cast address for the Cooking In The Dark Show is.
http://www.gcast.com/u/cookingindark/main.xml
Visit The Blind Handy Man Files Page To Review Contributions From Various List
Members At The Following address:
http://www.jaws-users.com/handyman/
Visit the new archives page at the following address
http://www.mail-archive.com/blindhandyman@yahoogroups.com/
For a complete list of email commands pertaining to the Blind Handy Man list
just send a blank message to:
[EMAIL PROTECTED]
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/blindhandyman/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/blindhandyman/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:[EMAIL PROTECTED]
mailto:[EMAIL PROTECTED]
<*> To unsubscribe from this group, send an email to:
[EMAIL PROTECTED]
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
