Hi Everyone
I need some clarity on a call flow that uses multiple ICT/H323 Trunks.
Here is the scenario:
Cluster 1
Cluster 2
Cluster 3
WAN
WAN
PH 1 --- GK Trunk (G729 Region)
Hello,
I have any issue is that when making a call from HQ Phones to BR2 Phones SCCP
or SIP,the call keeps ringing even after i pick up the call.
I check the same configuration as is done in Proctor Guide but still cannot
make it work, any one face that issue?.
Best regards,
Hi Amr,
Its being send via the Gatekeeper right?
Sounds like the usual codec issue...
Check your complete call flow if you have the the same codec and if
there is a transcoder needed.
If this doesn't help provide some more details please.
Hth,
Bernhard
Von:
Hi ,
can you post your dialpeer configuration
hth
amr
On Thu, Oct 7, 2010 at 12:24 AM, Pithog Oil pithog...@yahoo.com wrote:
I spent some time trying to figure out a fix but, i have not gotten the
solution yet, whenever i call *2123945010* in an attemp to invoke my MVA
application, it rings
Hi Amr,
since you are doing lab 1, and it has CUBE involved right. So make sure the
following need to check and configure
Configure Xcoder and IOS MTP on HQ
On the trunk, make sure to
- Checked MTP
- Unchecked 'Wait for H245 capacity set'
- Checked Enable Inbound Fast Start
Hope
Hi,
Did you put a codec on hq-rtr ?
br2ph (CME) hq-rtr(GK) -- CCM
zone UCME G711CUBEG729 zone UCM
As you can see you’re involving a different codec for the inbound call leg and
outbound call leg at the hq-rtr
And CUBE doesn’t support
Hi,
Did you put a xcoder on hq-rtr ?
br2ph (CME) hq-rtr(GK) -- CCM
zone UCME G711CUBEG729 zone UCM
As you can see you’re involving a different codec for the inbound call leg and
outbound call leg at the hq-rtr
And CUBE doesn’t support
Yeah. What Tam said. Just to note: the MRGL used for your trunk should
include the IOS MTP you configured, and this MUST be registered with CUCM.
Keep this in mind, since the Xcoder would be registered to CUCME on HQ-RTR.
On Thu, Oct 7, 2010 at 2:14 PM, Tam Nhu tamnhu...@gmail.com wrote:
Hi
Another thing
Incoming call leg to CME is G711 (DP incoming) as resquested
if default codec for the sip phone is registered on cme (default G.729), you
will need a xcoder on cme
Or just put a codec g711ulaw on the voice register pool and it gonna work
withtout any xcoder on the cme
Regards
Hello ,
Yesterday While I was practicing voice Workbook 1 Lab 4A I saw that phones
belonging to the HQ PHONE2 and BR1 PHone2 are preconfigured on call manager as
device types of 7960 and CIPC.I have two 7965 for HQPHONE2 and BR1Phone2 in my
site.Is there any easy way to transfer the
Hi,
You might be using some feature that is not supported by your license...
What license do you have and what features are you using???
Cheers,
On Wed, Oct 6, 2010 at 11:25 PM, CCIE Voice GMAIL
givemeccievoice2...@gmail.com wrote:
I know that sometimes the thing that fixes problems like
Hi,
When you book the remote racks on proctorlabs.com there is no limitation at all.
The only thing you need is a few hardphones and a router and a switch to set up
the EzVPN connection in order to register your own phones.
If that does not answer your question please let me know!
Iwan
Hi,
My procedure is usually to just enable autoregistration for only the subscriber
...
Let your phones register ...
You will see the phones that are of IPexpert and your own phones.
Once your own phones are registered you can disable autoregistration and delete
the IPexpert phones and leave
Hi all,
I have this scenario
Hardware CFB configured in HQ
Ad-hoc conferene started by hq phone1 with br1 phone1 and br1 phone2. No
problem with this
HQ#SH sccp connections
sess_idconn_idstype mode codec ripaddr rport sport
33556436 33554594 conf sendrecv g729b
Hi,
Do you have any shared lines in your scenario across the two phones you are
conferencing ie shared lines between HQ , A or B phones? If so every call to
shared line needs 24kbps across the WAN.
HTH
Prashant
On Thu, Oct 7, 2010 at 2:16 PM, Roig Borrell, Francesc Xavier
Hi,
I run into the same issue.
furthermore i have to hairpin the call through a h323 gateway as all incoming
calls come per mgcp to the callmanager. You have then to add a H.323 gateway to
the same mgcp gateway which is possible.
I got following dial--peers configured:
dial-peer voice 1999
Just wondering if anyone encountered this problem.
I still can't get MOH when calling the PSTN phone and the site is not in SRST
mode. According to the sh command below. The call manager has done its job
but the GWY is not responding. Any ideas? MOH local and between HQ works
fine. Just
Hi Ayman,
I would prefer to have a look on the Regions and Codecs, I have had a similar
issue like this
Regards
Wilson Samuel
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of ayman labib
Sent: Thursday, October 07, 2010 2:56 PM
To:
Hi Stutz,
1- add translation rule profile to dial-p 1997 to change the calling
number to be '8884343' .
2- if still have a problem , check css of RDP and may restart Mobile Voice
Service
I hpoe this may help
HTH
AMR
On Thu, Oct 7, 2010 at 9:26 PM, Stutz, Bernhard st...@pandacom.de wrote:
All,
In Volume 2 lab 2, I have been held up by the GK question 4.4. The output I
have is
HQ-RTR#sh gatekeeper endpoints
GATEKEEPER ENDPOINT REGISTRATION
CallSignalAddr Port RASSignalAddr Port Zone Name Type
Hi romain
Go to service parameter search for the value 1720 then type in you gatekeeper
registered name gk-trunk into the parameter allocated space, that will get
the trick done for you.
That is a good way to harcode your port numbers.
___
For
Hi Expert
please i will like to know if it is a normal behaviour for CUE to tell me, to
record a message that is at least 2 seconds long , and even when i record a
message longer than 2 seconds it continues to tell me the same thing.
i might have mis configured some parameters, kindly light me
Thanks for the reply.
As it turns out. Loopback interface is a required step. Now everything is
working. Thanks
Next challenge is to get Site HQ and SRST to use MoH with CME using the
Gatekeeper. Thanks
From: ayman labib ayman_la...@yahoo.com
To: amr
.
___
For more information regarding industry leading CCIE Lab training, please
visit www.ipexpert.com
-- next part --
An HTML attachment was scrubbed...
URL: /archives/ccie_voice/attachments/20101007/ef5d9d2c/attachment-0001.html
Hi
Did you put your gk-trunk name in the service parameters of the CCM ??
to use the port 1720 for this trunk name ...
make a search for trunk in service parameters
Regards
De: ccie_voice-boun...@onlinestudylist.com de la part de Romain Mullier
Date:
/ccie_voice/attachments/20101007/ef5d9d2c/attachment-0001.html
--
Message: 2
Date: Thu, 7 Oct 2010 16:15:27 +0200
From: Friderich Claude cfrider...@netcore.lu
To: Amr Sherif miroale...@hotmail.com,
ccie_voice@onlinestudylist.com
Subject: [OSL | CCIE_Voice] RE
Yes it is what the problem was. Thank you all.
On Thu, Oct 7, 2010 at 6:11 PM, Friderich Claude cfrider...@netcore.luwrote:
Hi
Did you put your gk-trunk name in the service parameters of the CCM ??
to use the port 1720 for this trunk name ...
make a search for trunk in service
Hey Amr,,
This is what i was trying to tell you earlier. You want to register the MTP
in CUCM, right? But look at your address in the 2nd line of your config:
sccp ccm 10.10.200.3 identifier 1 version 5.0.1
This is pointing to your GW, not CUCM. The MTP needs to be as part of
another sccp ccm
Hey everyone,
I'm struggling to get calls to work from HQ or SB to SC through the GK to
CUE. I'm figuring it's a problem with the Transcoder b/c the calls across
the WAN are G729 and CUE only accepts G711ulaw.
Any ideas what to do for this?
Here is the relevant configurations:
29 matches
Mail list logo