Hi men,
I have question:
During lab, tasks are provided in electronic form or on paper?
--
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www
Hey guys.
I m in trouble with the phone connected to Fa1/0/23 of the 3750 in HQ.
Vlan assignement are OK:
HQ-3750#sh run int fa1/0/23
Building configuration...
Current configuration : 113 bytes
!
interface FastEthernet1/0/23
switchport access vlan 10
switchport voice vlan 20
spanning-tree po
It might be IP dhcp snooping...
On Tue, Jan 8, 2013 at 7:57 AM, Nicolas MICHEL wrote:
> Hey guys.
>
> I m in trouble with the phone connected to Fa1/0/23 of the 3750 in HQ.
>
> Vlan assignement are OK:
> HQ-3750#sh run int fa1/0/23
> Building configuration...
>
> Current configuration : 113 byt
I am trying to integrate CME to UCx using Skinny but I am stuck with the
"Failed to send message to remote AXL server. " message.
I have in Phone System CUCM AXL Servers the IP of the CME and the https
port (443), ip http secure-server enabled, xml username/pwd set, ixi
transport and application
Nic,
On your HQ router, can you check Fa0/0.10? Make sure you have the following
config:
encapsulation dot1q 10 native
I don't think it is DHCP snooping or you would not receive an IP address.
However, you could (and should) Erase the config on the IP phone to ensure it
isn't just using an "
check this doc
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/integration/cucme_sccp/guide/cucintcucmesccp050.html
But its much easier with sip integration
dial-peer voice 3 voip
description voice mail pilot
max-conn 8
destination-pattern (voicemail number
session protocol si
I had already followed that, and my bad that I was stuck in where I wanted
to get the users from CME to UCx!
Its done.
Thanks again.
On Tue, Jan 8, 2013 at 10:55 PM, Chrysostomos Christofi <
ch.christ...@logicom.net> wrote:
> check this doc
>
>
> http://www.cisco.com/en/US/docs/voice_ip_
Hi Nicolas,
I had this problem too on some pods, where only one of the HQ phones want
to register, same for site B, dhcp addressing is working but no
registration occurs. Because I had no physical access on the phones to
check what the display is showing ( I guess something like registration
rejec
Hesham,
Please OSL is a support list owned and operated by IPexpert. Please
refrain from discussing our competitors' products and services here.
Thank you.
--
Marko Milivojevic - CCIE #18427 (SP R&S)
Senior CCIE Instructor - IPexpert
On Tue, Jan 8, 2013 at 10:04 AM, Hesham Abdelkereem
wrote:
>
Hi All,
What is the idea behind of numbering plan, Such as ISDN , NATIONAL , etc.
How it can be applied in real world.
Thanks,
IE.
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or C
Hi All,
I configured a user in the CUE to send broadcast message, he is able to
send the message, the MWI ON appear on the phone, but when recipient hear
the broadcast message and the message deleted, the red alarm and the
envelop does not disappear , the MWI OFF is not working, until I perform
th
Guys Seems that I am asking, then I can find an answer to my questions, :)
I find the following cisco document :
*
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/design/design21/cuevmdes.html#wp1008620
*
Which says clearly that "WI operation for broadcast messaging cannot be
controlled p
Hi Guys !
Yeah I have checked fa0/0.10 and it is ok !
I cannot access to the IP phone since it is PL facilities :) DHCP scope
has been created/deleted/checked etc etc
I had no problem with BR1 or BR2 ... only with the 7962 in HQ .. Weird !
I have the same rack tomorrow for the same lab (VOL2
Hello,
is it advisable to bring down the Connection Monitor Duration under Device Pool
to a low value like 30 seconds to expedite the SRST testing in the lab? Does it
affect grading if we happen to put it back to default?
thx ___
Hello,
I have a small query about Gatekeeper in single zone configuration it is
prefer PUB as call processing ( as per ARQ message).
if lab requirement says make subscriber as call processing engine then it
does not meet requirement.
Does any one know the answer what is the solution of this tric
Nic,
Ive been battling a somewhat similar problem in my own lab (I have all the
hardware on my rack with full access) and the problem was that somehow one
of the phones was not taking the default gateway set in PUBs DHCP. I
configured a pool locally on the router and it worked then. Next day
Both is available on the desktop (in Brussels)
Am Mittwoch, 9. Januar 2013 schrieb Abdullin Kamil :
> Hi men,
> On lab what program is used for remote access on UCCX?
> windows remote desktop, VNC or any other?
> Thanks!
>
>
>
___
For more information r
You can define a gw-priority for the trunks to each endpoint.
Am Mittwoch, 9. Januar 2013 schrieb Ramcharan Arya :
> Hello,
>
> I have a small query about Gatekeeper in single zone configuration it is
> prefer PUB as call processing ( as per ARQ message).
>
> if lab requirement says make subscrib
I always put it down to 10s, not less because sometimes the wan connection
is flapping/very low and so the phones flapping between cucm and srst.
Am Mittwoch, 9. Januar 2013 schrieb Pixar Perfect :
> Hello,
>
> is it advisable to bring down the Connection Monitor Duration under Device
> Pool to
19 matches
Mail list logo
