Posts'
Subject: RE: Advice on Desoldering an IC
I decided to invest in a Hakko FR-301. It worked almost immediately. Hours of
trying before, I did it in 10 minutes!
Regards
Rob
> -Original Message-
> From: cctalk On Behalf Of dwight via
> cctalk
> Sent: 16 April 20
On 4/22/22 12:03 PM, Rob Jarratt via cctalk wrote:
I decided to invest in a Hakko FR-301. It worked almost
immediately. Hours of trying before, I did it in 10 minutes!
Thank you for the feedback and the comparison of without and with it.
--
Grant. . . .
unix || die
-Topic Posts
>
> Subject: Re: Advice on Desoldering an IC
>
> Sometimes the IC has been installed with the pins under tension. This is
> typical of machine inserted ICs. When the solder is loose, bend the pin away
> from the side it is pressed against. Do this carefully, don't ov
YOUR TIP FREE OF THIN OXIDE!
Dwight
From: cctalk on behalf of Rob Jarratt via
cctalk
Sent: Friday, April 15, 2022 10:49 AM
To: General Discussion: On-Topic and Off-Topic Posts
Subject: Advice on Desoldering an IC
I am trying to remove an IC from my PDP 11/24 CPU,
I had to desolder a fairly large number of 14/16 pin ICs from a two layer
PCB recently. I had an basic soldering iron and a spring loaded solder
sucker thing. I also had some wick but never having had good results with
this, I decided not to bother trying it this time.
I was aware of the idea of
As mentioned, I find it best to cut the pins off the IC right at the IC
body and then remove them individually. Once the IC is removed, I use a
third hand to hold the board vertically, and then grab each pin with
tweezers or needle-nose pliers from one side of the board and lightly
touch the s
On 4/15/22 17:12, W2HX wrote:
> Just be careful around cerroblend. According to Wikipedia...
>
> "... is a metal alloy that is useful for soldering and making custom metal
> parts, but which is toxic to touch or breathe vapors from."
> "...is toxic because it contains lead and cadmium, and conta
k
Subject: Re: Advice on Desoldering an IC
For very-difficult de-soldering, I use a variation on the Chip-Quik
idea. I take a hunk of Cerrobend 158 fusible alloy and a file and make
a small pile of powder from it. I then pack the powder around the pins of the
IC to remove and heat the area using the
For very-difficult de-soldering, I use a variation on the Chip-Quik
idea. I take a hunk of Cerrobend 158 fusible alloy and a file and make
a small pile of powder from it. I then pack the powder around the pins
of the IC to remove and heat the area using the light from a 75 watt
PAR-38 halogen re
Once the chip is out, for cleaning out the holes, I used a spring loaded
solder sucker on one side of the board, with soldering iron on the other
side.
also, solder wick
sometimes a wooden toothpick
in extreme cases, a small drill bit turned by hand in a pin vise (NOT
chucked up in a powered 1/
--Original Message-
From: cctalk [mailto:cctalk-boun...@classiccmp.org] On Behalf Of Rob Jarratt
via cctalk
Sent: 15 April 2022 22:33
To: 'Chris Zach' ; 'General Discussion: On-Topic and
Off-Topic Posts'
Subject: RE: Advice on Desoldering an IC
I do have some diagonal cu
April 2022 18:51
To: r...@jarratt.me.uk; Rob Jarratt ; General Discussion:
On-Topic and Off-Topic Posts ; Rob Jarratt via cctalk
Subject: Re: Advice on Desoldering an IC
Cut the pins with a very sharp set of dykes then remove them one at a time.
Then use flux and detailer braid to remove the s
; Rob Jarratt ; General
Discussion: On-Topic and Off-Topic Posts ; Rob Jarratt
via cctalk
Subject: Re: Advice on Desoldering an IC
Cut the pins with a very sharp set of dykes then remove them one at a time.
Then use flux and detailer braid to remove the solder
On April 15, 2022 1:49:33 PM EDT
eral Discussion: On-Topic and Off-Topic Posts
Subject: Advice on Desoldering an IC
I am trying to remove an IC from my PDP 11/24 CPU, a DS8641. I am really
struggling to desolder it. I am using the technique of applying fresh solder
and then removing it. But after multiple cycles of this I think
utube Channel: https://www.youtube.com/c/w2hx-channel/videos
-Original Message-
From: cctalk On Behalf Of Rob Jarratt via cctalk
Sent: Friday, April 15, 2022 1:50 PM
To: General Discussion: On-Topic and Off-Topic Posts
Subject: Advice on Desoldering an IC
I am trying to remove an IC fr
On 15/04/2022 18:49, Rob Jarratt via cctalk wrote:
I am using a fairly cheap desoldering station (this one
https://cpc.farnell.com/duratool/d00672/desoldering-station-uk-eu-plug/dp/SD
01384?st=duratool%20desoldering). Its spec in terms of vacuum pressure is
equivalent to that of the professional
I have to second this comment.
I learned to solder in the early 70s building kits and again
professionally in the early 80s.
In the early days of thicker circuit boards (2 layer only). A solder
sucker and solder wick would work.
However, the most expedient and safest way in terms of potent
I am trying to remove an IC from my PDP 11/24 CPU, a DS8641. I am really
struggling to desolder it. I am using the technique of applying fresh solder
and then removing it. But after multiple cycles of this I think I am
starting to damage the PCB.
Are there any tips for removing ICs?
Thanks
Rob
Cut the pins with a very sharp set of dykes then remove them one at a time.
Then use flux and detailer braid to remove the solder
On April 15, 2022 1:49:33 PM EDT, Rob Jarratt via cctalk
wrote:
>I am trying to remove an IC from my PDP 11/24 CPU, a DS8641. I am really
>struggling to desolder it.
I am trying to remove an IC from my PDP 11/24 CPU, a DS8641. I am really
struggling to desolder it. I am using the technique of applying fresh solder
and then removing it. But after multiple cycles of this I think I am
starting to damage the PCB.
I am using a fairly cheap desoldering station (t
20 matches
Mail list logo