Raffaele,
> -Original Message-
> From: davinci-linux-open-source-boun...@linux.davincidsp.com
> [mailto:davinci-linux-open-source-boun...@linux.davincidsp.com] On Behalf
> Of Raffaele Recalcati
> Sent: Friday, October 30, 2009 9:26 AM
> To: davinci-linux-open-source@linux.davincidsp.com
>
Andrey Porodko writes:
> The Neuros OSD 2.0 is the hardware component of the Neuros Open
> Internet Television Platform. Hardware is very close to Ti DM644X-EVM board.
> It has: DM6446M02 module with 256MB NAND, 256MB RAM, TLV320AIC32 AIC,
> USB, Ethernet, SD/MMC, UART, THS8200, TVP7000 for
Hi Santiago,
See review comments below:
On Friday 06 November 2009 16:42:56 santiago.nu...@ridgerun.com wrote:
> From: Santiago Nunez-Corrales
>
> This patch provides the implementation of the TVP7002 decoder
> driver for DM365. Implemented using the V4L2 DV presets API.
>
> Signed-off-by: San
hi, all
what's the typical value of davinci vpbe basex and basey for a
PAL/NTSC TV display? should I set the osd/vid's X/Y postion register
or basex/basey to adjust the display postion? I do a simple test, if
set fixed osd/vid's X/Y position register, then the display will
currupt while othe
hi, all
Can I configure the osd/vid use different resolution for dm6441?
for example: vid1: 720*576, osd0:800*480, osd1:800*576. and if I can,
what's the resolution of vid0 should be? the vpbe spec require that
vid1/osd0/osd1 should be fully contained in vid0, so should the
minimum vid0 resol
Hi Santiago,
See review comments below:
On Friday 06 November 2009 16:42:40 santiago.nu...@ridgerun.com wrote:
> From: Santiago Nunez-Corrales
>
> This patch provides the required definitions for the TVP7002 driver
> in DM365.
>
> Signed-off-by: Santiago Nunez-Corrales
> ---
> drivers/media/
I have qt4 working on DM365 EVM (DaVinci PSP 03.01 Phase 2 Release - Build r26).
QT writes, in RGB, to fb3 that is YUV and goes out to COMPONENT output.
Anybody can point me to the correct direction in order to write, with
QT, to OSD0 or OSD1 and than let me see it to COMPONENT output?
I don't find
Hi All
I am a new comer of Mailist, would you please tell me how to download thest
patchs referred to the mailist
Thank you
Regards!
--
Young Chen
___
Davinci-linux-open-source mailing list
Davinci-linux-open-source@linux.davincidsp.com
http://linux.
Thanks for the VOL header tip. I printed out the first 64 bytes of each encoded frame and found the VOL header in the first frame after creating the videnc algorithm. 28 bytes up until the 0-0-1-B6 start of frame code.
I could not find any way to force it to add a header to a frame.
The headers a
Hii all,
I am unable to get the arm 9 processor to wake up after putting it to deep
sleep. I have used the patch available at
http://www.mail-archive.com/davinci-linux-open-source@linux.davincidsp.com/msg07928.html.
It puts DM355 to deep sleep but however it is unable to wake up DM355 when
GPIO0
10 matches
Mail list logo