--- Begin Message ---
Package: linux-image-2.6.26-1-686
Version: 2.6.26-1
Severity: normal
I use kernel's ath5k driver for my Atheros AR5413 based card. I'm always quite
close to the AP, and iwconfig shows "Signal level=-57 dBm". Despite of it, the
card often disconnects (about once in 10 min.) and reconnects again, and
always works with bitrates like 1-9 Mbit/s. Trying to higher bitrate manually
I get connection loss. This is not happening when I use madwifi (with
2.6.25-2-686 kernel). The antenna in both AP and station is OK, and other
cards work OK with this AP, and mine also when using Windows (as MadWifi has
other annoying bug, though is usable anyway).
-- Package-specific info:
** Version:
Linux version 2.6.26-1-686 (Debian 2.6.26-1) (wa...@debian.org) (gcc version
4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Wed Jul 30 20:02:15 UTC 2008
** Command line:
BOOT_IMAGE=Debian ro root=UUID=2ecae58f-eae1-4d67-b0d6-8f8cc0ecbae2 resume
** Tainted: P (1)
** Kernel log:
[ 15.721385] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.799440] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 19.939928] Linux agpgart interface v0.103
[ 20.063928] Yenta: CardBus bridge found at 0000:00:14.0 [1071:8351]
[ 20.090227] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 20.118071] Yenta: Routing CardBus interrupts to PCI
[ 20.144030] Yenta TI: socket 0000:00:14.0, mfunc 0x01001022, devctl 0x66
[ 20.455428] uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
[ 21.197674] input: Power Button (FF) as /class/input/input1
[ 21.629222] ACPI: Power Button (FF) [PWRF]
[ 21.700608] Yenta: ISA IRQ mask 0x0cf8, PCI irq 17
[ 21.727227] Socket status: 30000086
[ 22.060630] input: Sleep Button (CM) as /class/input/input2
[ 22.440541] ACPI: PCI Interrupt 0000:00:15.0[A] -> GSI 18 (level, low) ->
IRQ 18
[ 22.467714] ath5k_pci 0000:00:15.0: registered as 'phy0'
[ 22.603474] ACPI: Sleep Button (CM) [SBTN]
[ 22.854694] input: Lid Switch as /class/input/input3
[ 23.081220] input: PC Speaker as /class/input/input4
[ 23.204064] ACPI: Lid Switch [LID]
[ 23.356214] ACPI: AC Adapter [AC] (off-line)
[ 23.558342] ACPI: Battery Slot [BAT0] (battery present)
[ 23.753123] phy0: Selected rate control algorithm 'pid'
[ 25.385144] ath5k phy0: Atheros AR5413 chip found (MAC: 0xa4, PHY: 0x61)
[ 25.412701] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 20 (level, low) ->
IRQ 20
[ 25.466948] eth0: ULi M5263 at pci0000:00:1b.0, 00:40:d0:8a:93:74, irq 20.
[ 25.582788] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 25.616910] ali1535_smbus 0000:00:1e.1: ALI1535_smb region uninitialized -
upgrade BIOS?
[ 25.644863] ali1535_smbus 0000:00:1e.1: ALI1535 not detected, module not
inserted.
[ 25.823693] Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa5a0b1, caps:
0xa04713/0x0
[ 25.901840] input: SynPS/2 Synaptics TouchPad as /class/input/input5
[ 26.021893] cs: IO port probe 0x100-0x3af: clean.
[ 26.059196] cs: IO port probe 0x3e0-0x4ff: clean.
[ 26.092013] ali15x3_smbus 0000:00:1e.1: ALI15X3_smb region uninitialized -
upgrade BIOS or use force_addr=0xaddr
[ 26.120043] ali15x3_smbus 0000:00:1e.1: ALI15X3 not detected, module not
inserted.
[ 26.208382] cs: IO port probe 0x820-0x8ff: clean.
[ 26.334433] cs: IO port probe 0xc00-0xcf7: clean.
[ 26.450602] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) ->
IRQ 23
[ 26.492009] cs: IO port probe 0xa00-0xaff: clean.
[ 26.581471] intel8x0_measure_ac97_clock: measured 93116 usecs
[ 26.610825] intel8x0: clocking to 48000
[ 27.952169] Adding 1012084k swap on /dev/hda4. Priority:-1 extents:1
across:1012084k
[ 28.398328] EXT3 FS on hda2, internal journal
[ 29.316477] powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology ML-32
processors (1 cpu cores) (version 2.20.00)
[ 29.377698] powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x4
[ 29.409649] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x6
[ 29.439879] powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x16
[ 29.768033] Clocksource tsc unstable (delta = 364052943 ns)
[ 33.838928] kjournald starting. Commit interval 5 seconds
[ 33.862570] EXT3 FS on hda3, internal journal
[ 33.886344] EXT3-fs: mounted filesystem with ordered data mode.
[ 37.927212] fglrx: module license 'Proprietary. (C) 2002 - ATI
Technologies, Starnberg, GERMANY' taints kernel.
[ 37.928082] Symbol init_mm is marked as UNUSED, however this module is
using it.
[ 37.928085] This symbol will go away in the future.
[ 37.928088] Please evalute if this is the right api to use and if it really
is, submit a report the linux kernel mailinglist together with submitting your
code for inclusion.
[ 37.952435] [fglrx] vendor: 1002 device: 5955 count: 1
[ 37.953082] [fglrx] ioport: bar 1, base 0xc000, size: 0x100
[ 37.953090] [fglrx] Maximum main memory to use for locked dma buffers: 403
MBytes.
[ 37.953933] [fglrx] PAT is enabled successfully!
[ 37.953968] [fglrx] module loaded - fglrx 8.51.3 [Jul 3 2008] with 1 minors
[ 37.987462] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) ->
IRQ 17
[ 40.225000] [fglrx] GART Table is not in FRAME_BUFFER range
[ 40.230206] [fglrx] Reserved FB block: Shared offset:0, size:40000
[ 40.230226] [fglrx] Reserved FB block: Unshared offset:1ff5000, size:b000
[ 40.336727] lp: driver loaded but no devices found
[ 40.403608] ppdev: user-space parallel port driver
[ 42.626980] warning: `avahi-daemon' uses 32-bit capabilities (legacy
support in use)
[ 45.949387] Bluetooth: Core ver 2.11
[ 45.952009] NET: Registered protocol family 31
[ 45.952009] Bluetooth: HCI device and connection manager initialized
[ 45.952009] Bluetooth: HCI socket layer initialized
[ 45.994840] Bluetooth: L2CAP ver 2.9
[ 45.994856] Bluetooth: L2CAP socket layer initialized
[ 46.148597] Bluetooth: RFCOMM socket layer initialized
[ 46.148631] Bluetooth: RFCOMM TTY layer initialized
[ 46.148636] Bluetooth: RFCOMM ver 1.8
[ 50.764689] uli526x: eth0 NIC Link is Down
[ 122.211913] [fglrx] GART Table is not in FRAME_BUFFER range
[ 122.217032] [fglrx] Reserved FB block: Shared offset:0, size:40000
[ 122.217051] [fglrx] Reserved FB block: Unshared offset:1ff5000, size:b000
[ 153.792069] usb 1-1: new low speed USB device using ohci_hcd and address 2
[ 154.016064] usb 1-1: configuration #1 chosen from 1 choice
[ 154.040913] usb 1-1: New USB device found, idVendor=046d, idProduct=c03e
[ 154.040930] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 154.040937] usb 1-1: Product: USB-PS/2 Optical Mouse
[ 154.040943] usb 1-1: Manufacturer: Logitech
[ 154.249871] usbcore: registered new interface driver hiddev
[ 154.263748] input: Logitech USB-PS/2 Optical Mouse as /class/input/input6
[ 154.264755] input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical
Mouse] on usb-0000:00:1c.0-1
[ 154.264804] usbcore: registered new interface driver usbhid
[ 154.264812] usbhid: v2.6:USB HID core driver
[ 175.501717] wlan0: Initial auth_alg=0
[ 175.501736] wlan0: authenticate with AP 00:0e:2e:df:16:45
[ 175.503182] wlan0: RX authentication from 00:0e:2e:df:16:45 (alg=0
transaction=2 status=0)
[ 175.503193] wlan0: authenticated
[ 175.503200] wlan0: associate with AP 00:0e:2e:df:16:45
[ 175.504747] wlan0: RX AssocResp from 00:0e:2e:df:16:45 (capab=0x431
status=0 aid=1)
[ 175.504747] wlan0: associated
[ 273.169306] [fglrx] GART Table is not in FRAME_BUFFER range
[ 273.174408] [fglrx] Reserved FB block: Shared offset:0, size:40000
[ 273.174427] [fglrx] Reserved FB block: Unshared offset:1ff5000, size:b000
** Loaded modules:
Module Size Used by
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
binfmt_misc 7528 1
rfcomm 28272 2
l2cap 17248 9 rfcomm
bluetooth 44900 4 rfcomm,l2cap
ppdev 6468 0
parport_pc 22532 0
lp 8164 0
parport 30988 3 ppdev,parport_pc,lp
fglrx 1740548 20
cpufreq_stats 3776 0
cpufreq_userspace 3172 0
cpufreq_conservative 5960 0
cpufreq_ondemand 6476 1
cpufreq_powersave 1856 0
powernow_k8 12036 0
freq_table 4224 3 cpufreq_stats,cpufreq_ondemand,powernow_k8
joydev 8480 0
snd_intel8x0 26268 1
snd_ac97_codec 88484 1 snd_intel8x0
ac97_bus 1728 1 snd_ac97_codec
snd_pcm_oss 32800 0
snd_pcm 62628 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
i2c_ali15x3 6020 0
snd_mixer_oss 12320 1 snd_pcm_oss
pcmcia 29548 0
firmware_class 6816 1 pcmcia
arc4 1824 2
ecb 2624 2
crypto_blkcipher 15236 1 ecb
snd_seq_dummy 2660 0
psmouse 32336 0
serio_raw 4740 0
i2c_ali1535 5508 0
i2c_core 19828 2 i2c_ali15x3,i2c_ali1535
snd_seq_oss 24960 0
snd_seq_midi 5728 0
snd_rawmidi 18560 1 snd_seq_midi
pcspkr 2432 0
snd_seq_midi_event 6432 2 snd_seq_oss,snd_seq_midi
snd_seq 41456 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 17800 2 snd_pcm,snd_seq
snd_seq_device 6380 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 45604 12
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
battery 6272 0
ac 3264 0
soundcore 6368 1 snd
snd_page_alloc 7816 2 snd_intel8x0,snd_pcm
button 6064 0
uli526x 13232 0
ati_agp 6220 0
k8temp 4064 0
shpchp 25528 0
ath5k 87200 0
mac80211 139680 1 ath5k
cfg80211 21576 2 ath5k,mac80211
yenta_socket 20620 1
rsrc_nonstatic 9504 1 yenta_socket
pcmcia_core 31892 3 pcmcia,yenta_socket,rsrc_nonstatic
agpgart 28776 2 fglrx,ati_agp
pci_hotplug 23460 1 shpchp
evdev 8000 5
ext3 105256 2
jbd 39380 1 ext3
mbcache 7108 1 ext3
ide_cd_mod 27524 0
cdrom 30176 1 ide_cd_mod
ide_disk 10496 4
ata_generic 4676 0
libata 140416 1 ata_generic
scsi_mod 129356 1 libata
dock 8272 1 libata
ide_pci_generic 3908 0 [permanent]
ohci_hcd 18500 0
ehci_hcd 28428 0
alim15x3 5836 0 [permanent]
ide_core 92628 4 ide_cd_mod,ide_disk,ide_pci_generic,alim15x3
usbcore 118160 4 usbhid,ohci_hcd,ehci_hcd
ohci1394 24944 0
ieee1394 75800 1 ohci1394
thermal 15228 0
processor 32548 3 powernow_k8,thermal
fan 4164 0
thermal_sys 10856 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc RS480 Host Bridge [1002:5950]
(rev 10)
Subsystem: Mitac Device [1071:8351]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
Kernel modules: ati-agp
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000dfff
Memory behind bridge: c0000000-cfffffff
Prefetchable memory behind bridge: 0000000090000000-000000009fffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
00:14.0 CardBus bridge [0607]: Texas Instruments PCI4510 PC card Cardbus
Controller [104c:ac44] (rev 03)
Subsystem: Mitac Device [1071:8351]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at 38000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 30000000-33fff000 (prefetchable)
Memory window 1: 34000000-37fff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
00:14.1 FireWire (IEEE 1394) [0c00]: Texas Instruments PCI4510 IEEE-1394
Controller [104c:8029] (rev 01) (prog-if 10)
Subsystem: Mitac Device [1071:8351]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (500ns min, 1000ns max), Cache Line Size: 16 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0004000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
00:15.0 Ethernet controller [0200]: Atheros Communications Inc. AR5413
802.11abg NIC [168c:001b] (rev 01)
Subsystem: Atheros Communications Inc. Device [168c:2063]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0010000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath5k_pci
Kernel modules: ath5k
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
Kernel modules: k8temp
00:19.0 PCI bridge [0604]: ALi Corporation M5249 HTT to PCI Bridge [10b9:5249]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: b8000000-bfffffff
Prefetchable memory behind bridge: 88000000-8fffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
00:1b.0 Ethernet controller [0200]: ALi Corporation ULi 1689,1573 integrated
ethernet. [10b9:5263] (rev 50)
Subsystem: Mitac Device [1071:8351]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at e000 [size=256]
Region 1: Memory at d0020000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: uli526x
Kernel modules: uli526x
00:1c.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237]
(rev 03) (prog-if 10)
Subsystem: Mitac Device [1071:8351]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64 (20000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f8002000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:1c.1 USB Controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237]
(rev 03) (prog-if 10)
Subsystem: Mitac Device [1071:8351]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64 (20000ns max)
Interrupt: pin B routed to IRQ 18
Region 0: Memory at f8003000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:1c.3 USB Controller [0c03]: ALi Corporation USB 2.0 Controller [10b9:5239]
(rev 01) (prog-if 20)
Subsystem: Mitac Device [1071:8351]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 8000ns max), Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 23
Region 0: Memory at 38001000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1d.0 Multimedia audio controller [0401]: ALi Corporation M5455 PCI AC-Link
Controller Audio Device [10b9:5455] (rev 20)
Subsystem: Mitac Device [1071:8351]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (16000ns min)
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at e100 [size=256]
Region 1: Memory at d0021000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00:1d.1 Modem [0703]: ALi Corporation M5457 AC'97 Modem Controller [10b9:5457]
(rev 20)
Subsystem: Mitac Device [1071:8351]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 22
Region 0: Memory at d0022000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e200 [size=256]
Capabilities: <access denied>
00:1e.0 ISA bridge [0601]: ALi Corporation PCI to LPC Controller [10b9:1573]
(rev 31)
Subsystem: Mitac Device [1071:8351]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 6000ns max)
00:1e.1 Bridge [0680]: ALi Corporation M7101 Power Management Controller [PMU]
[10b9:7101]
Subsystem: Mitac Device [1071:8351]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel modules: i2c-ali15x3, i2c-ali1535, alim7101_wdt
00:1f.0 IDE interface [0101]: ALi Corporation M5229 IDE [10b9:5229] (rev c7)
(prog-if 8a [Master SecP PriP])
Subsystem: Mitac Device [1071:8351]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1100 [size=16]
Capabilities: <access denied>
Kernel driver in use: ALI15x3_IDE
Kernel modules: alim15x3
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon XPRESS
200M 5955 (PCIE) [1002:5955]
Subsystem: Mitac Device [1071:8351]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at 90000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at c0000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at c0020000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: fglrx_pci
Kernel modules: fglrx, radeonfb
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-1-686 (SMP w/1 CPU core)
Locale: LANG=pl_PL, LC_CTYPE=pl_PL (charmap=ISO-8859-2)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-686 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92a tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-1-686 recommends:
ii libc6-i686 2.8~20080505-0ubuntu6 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-1-686 suggests:
ii lilo 1:22.8-4 LInux LOader - The Classic OS load
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information excluded
----------------------------------------------------------------------
Tylko dla detektywow! Konkurs na Smaker.pl
Kliknij >>> http://link.interia.pl/f1eb1
--- End Message ---