On Sun, Feb 10, 2013 at 02:49:21AM +0100, Javier Martinez Canillas wrote:
I knew this would be controversial and that's why I didn't mean it to be a
patch
but a RFC :)
The problem basically is that you have to associate the platform device with
its
corresponding DT device node because it
On Sun, Feb 10, 2013 at 10:37 AM, Russell King - ARM Linux
li...@arm.linux.org.uk wrote:
On Sun, Feb 10, 2013 at 02:49:21AM +0100, Javier Martinez Canillas wrote:
I knew this would be controversial and that's why I didn't mean it to be a
patch
but a RFC :)
The problem basically is that you
This patch adds support for parsing all platform-specific data from
Device Tree and instantiation using clocksource_of_init to samsung-time
clocksource driver.
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Tomasz Figa tomasz.f...@gmail.com
---
This series adds Device Tree support for Samsung S3C64xx SoC series.
It fixes several problems preventing from booting an S3C64xx-based system
using Device Tree, adds all the infrastructure for Device Tree-based board
support, including mach-s3c64xx-dt and dts include files for S3C64xx SoCs, and
This patch extends vic_of_init to parse valid interrupt sources
and resume sources masks from device tree.
If mask values are not specified in device tree, all sources
are assumed to be valid, as before this patch.
Signed-off-by: Tomasz Figa tomasz.f...@gmail.com
---
This patch adds basic device tree sources for FriendlyARM Mini6410 board
based on Samsung S3C6410 SoC.
Signed-off-by: Tomasz Figa tomasz.f...@gmail.com
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/s3c6410-mini6410.dts | 50 ++
2 files
+* QNAP Power Off
+
+QNAP NAS devices have a microcontroller controlling the main power
+supply. This microcontroller is connected to UART1 of the Kirkwood and
+Orion5x SoCs. Sending the charactor 'A', at 19200 baud, tells the
+microcontroller to turn the power off. This driver adds a
On Tue, 29 Jan 2013 15:53:39 +0100, Andreas Larsson andr...@gaisler.com wrote:
This lets of_gpio_named_count return an errno on errors by being able to
distinguish between reaching the end of the phandle list and getting some
other
error from of_parse_phandle_with_args.
Return error from
This patch creates of_count_phandle_with_args(), a new function for
counting the number of phandle+argument tuples in a given property. This
is better than the existing method of parsing each phandle individually
until parsing fails which is a horribly slow way to do the count.
It also converts
On Tue, 29 Jan 2013 15:53:41 +0100, Andreas Larsson andr...@gaisler.com wrote:
This adds missing kernel-doc entries for cs_gpios in struct spi_master and
cs_gpio in struct spi_device.
Signed-off-by: Andreas Larsson andr...@gaisler.com
Applied, thanks. I did tweak the language a bit.
g.
On Tue, 29 Jan 2013 15:53:40 +0100, Andreas Larsson andr...@gaisler.com wrote:
Using memset does not set an array of integers properly
Signed-off-by: Andreas Larsson andr...@gaisler.com
Applied, thanks.
g.
---
drivers/spi/spi.c |3 ++-
1 files changed, 2 insertions(+), 1
On Tue, 29 Jan 2013 15:53:42 +0100, Andreas Larsson andr...@gaisler.com wrote:
When using a gpio chip select with a OF_GPIO_ACTIVE_LOW flag, this needs to be
known to the controller driver.
Signed-off-by: Andreas Larsson andr...@gaisler.com
Out of curiosity, what do you need the flags for?
As there are no use of #address-cells and #size-cells properties
in pinctrl-single driver DT node. Fix pinctrl-single binding documentation
to remove these properties.
Signed-off-by: Kumar, Anil anilkuma...@ti.com
---
Tested on da850 EVM.
:100644 100644 2c81e45... c6384e2... M
On Mon, Jan 21, 2013 at 12:59:19PM -0800, Simon Glass wrote:
Given a set of nodes and properties, find the regions of the device tree
which describe those parts.
A test is provided which builds a tree while tracking where the regions
should be, then calls fdt_find_regions() to make sure that
I was just wondering if the following would be an acceptable way to turn
off an lcd backlight when the pwm-backlight driver is set to level 0.
The LCD backlight is 'powered' by the gpio.
leds {
compatible = gpio-leds;
backlight {
label = lcd-power;
15 matches
Mail list logo