Oops!
I did nothing other than run the wfm receiver and tried again. It worked!
Steve
On Fri, Jan 23, 2009 at 4:24 PM, Steve Glass wrote:
> Hi
>
> I'm using an RFX400 with my revision 3 USRP.
>
> After digging through the archive I found that I needed to modify the
> RFX400 and then update its
Hi
I'm using an RFX400 with my revision 3 USRP.
After digging through the archive I found that I needed to modify the RFX400
and then update its EEPROM as described here:
On Thu, Feb 8, 2007 at 10:18 AM, Matt Ettus wrote:
>
> All RFX boards currently shipping are configured for MIMO_B mode, wh
Hi
I get the message : "unable to locate an audio module" when trying the
dial_tone.py example
I have installed ALSA drivers - is there something else to check for?
regards
Russell
**
Relevant company disclaimers are availa
ok thanks
When I run usrp_nbfm_rcv.py from /usr/local/share/gnuradio/examples/usrp I
the following message appear on GUI
" Failed to set initial Frequency"
How can i frequency set to listen FM.
Take care
2009/1/23 Eric Blossom
> On Fri, Jan 23, 2009 at 12:25:25PM +1300, Muhammad Abrar wrote:
>
On Fri, Jan 23, 2009 at 12:25:25PM +1300, Muhammad Abrar wrote:
> Hi
> When I run usrp_wfm_rcv.py from /usr/local/share/gnuradio/examples/usrp I
> got following message.
>
>
> Using RX d'board A: Flex 1800 Rx MIMO B
> >>> gr_fir_ccf: using SSE
> >>> gr_fir_fff: using SSE
> FYI: No Powermate or Co
Hi
When I run usrp_wfm_rcv.py from /usr/local/share/gnuradio/examples/usrp I
got following message.
Using RX d'board A: Flex 1800 Rx MIMO B
>>> gr_fir_ccf: using SSE
>>> gr_fir_fff: using SSE
FYI: No Powermate or Contour Knob found
--
Engr. Muhammad Abrar
Massey University Palmerston North
New
Hi All,
I am doing video transmission using OFDM. At the receiver side, I save
payload to a file, meanwhile, use VLC to access this file to play the video.
However, VLC stops play the content while it reaches to the end of the file,
and does not wait for the continuosly coming payload. Is that p
http://bec-systems.com/site/326/intel-atom-vs-ti-omap3
Let the cage matches begin!
Philip
___
Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
On Thu, Jan 22, 2009 at 12:32:46AM -0800, Matt Ettus wrote:
> Yabo Li wrote:
>> I tried to compile the FPGA code use ISE 9.1i, I started from
>> "u2_core.v" as suggested. However it gives me two errors when I
>> compile the code.
>>
>>
>> Can anyone tell me how to fix this problem? Thanks very
On Thu, Jan 22, 2009 at 12:45:24PM -0500, Michael Dickens wrote:
> On Jan 22, 2009, at 12:29 PM, Johnathan Corgan wrote:
>> Looks like we're going to need to change the SWIG detection mechanism
>> in the build to conditionally define SWIGPYTHONARGS based on the
>> detected version. Do you want t
Stefan Brüns wrote:
Hi,
attached are some small cleanups for the inband code. Some are just cosmetic
changes, some give some small performance improvement (dont disassemble a
list and assemble the same list again, just pass it on ...)
Thanks Stefan!
I will look through the patch and doubl
On Jan 22, 2009, at 12:29 PM, Johnathan Corgan wrote:
Looks like we're going to need to change the SWIG detection
mechanism in the build to conditionally define SWIGPYTHONARGS based
on the detected version. Do you want to take stab at that?
GNU Radio right now requires SWIG 1.3.31 or newer,
On Thu, Jan 22, 2009 at 12:02:20PM -0500, Michael Dickens wrote:
> To get the output directory correct, one
> now needs to specify "-outcurrentdir" (or "-outdir .", which should be
> backwards compatible back to about version 1.3.20). It is clear from SVN
> [1] that this change is intentional,
Hi,
attached are some small cleanups for the inband code. Some are just cosmetic
changes, some give some small performance improvement (dont disassemble a
list and assemble the same list again, just pass it on ...)
Regards,
Stefan
--
Stefan Brüns / Bergstraße 21 / 52062 Aachen
mailto:lur
On Jan 22, 2009, at 11:43 AM, Johnathan Corgan wrote:
On Thu, Jan 22, 2009 at 11:39:25AM -0500, Michael Dickens wrote:
After further investigation, this is a SWIG 1.3.37 bug.
I retract this statement. I'm no longer sure if it's a bug. Issuing
"swig -help" in the different versions results
On Thu, Jan 22, 2009 at 11:39:25AM -0500, Michael Dickens wrote:
> After further investigation, this is a SWIG 1.3.37 bug.
Thanks for looking into this. What platform configuration are you using that
is shipping 1.3.37?
> I will submit a bug fix to the SWIG folks, since there
> doesn't seem t
Greg Troxel wrote:
> Several months ago I installed bbn 802.11 code and got it running. but today
> when I wanted to download it in my new PC (according to what I've done
> before http://gnuradio.org/trac/wiki/OtherCode)
>
> cvs -d anon...@acert.ir.bbn.com:/cvs/adroitgrdevel co adroitgrdev
After further investigation, this is a SWIG 1.3.37 bug. According to
the documentation [1], "the default output directory for these
language specific files is the same directory as the generated C/C++
file" ... which is clearly being violated since the .py file is being
written to the dire
Several months ago I installed bbn 802.11 code and got it running. but today
when I wanted to download it in my new PC (according to what I've done
before http://gnuradio.org/trac/wiki/OtherCode)
cvs -d anon...@acert.ir.bbn.com:/cvs/adroitgrdevel co adroitgrdevel
the problem is
cvs
Thank you for all Eric. At now I'm editing the diagram (there are some
block which names are in Portuguese).
I understood all when I connected the usrp(basicTX) to the spectrum
analyzer(SA). I verified that when I sweep the frequency (f_LO on
diagram), with f_signal(baseband)=0 Hz, I saw on SA 4 t
dqpsk.py module depends on mpsk_receiver_cc. In file
$GNURADIO/gnuradio-core/src/lib/general/gr_mpsk_receiver_cc.h there is
information:
* This block takes care of receiving M-PSK modulated signals through phase,
frequency, and symbol
* synchronization. It performs carrier frequency and phase lo
Yabo Li wrote:
I tried to compile the FPGA code use ISE 9.1i, I started from
"u2_core.v" as suggested. However it gives me two errors when I
compile the code.
-
ERROR:NgdBuil
I tried to compile the FPGA code use ISE 9.1i, I started from "u2_core.v" as
suggested. However it gives me two errors when I compile the code.
-
ERROR:NgdBuild:604 - logical blo
23 matches
Mail list logo
