Lyle Johnson wrote:
I don't think this is a problem with K3 at all. All you need to do
for split operation is to start by pressing A-B when on the DX' TX
frequency. Now both VFOs have the same frequency and modes.
Not here: VFO B comes to the same frequency as VFO A, but NOT the
same mode
W0JFR wrote:
You're right David, I'd like to listen on VFO B and transmit on VFO A. I
could do this on the K2. The reason I'd like to do it is because my
antenna tuning is based on the VFO A frequency. When you have big splits,
you really need the antenna tuned for the transmit frequency.
GM3SEK wrote:
Thanks, Lyle... though that is counter-intuitive compared with any of my
previous rigs.
It reinforces the request for a separate auto-split option that could
have a completely different (and dare I add, more conventional?)
behavior.
I doubt if that would be possible
hi all,
has anybody connected a Ptc-2 to the K3 and how this was done?
I think I could use Line in / Line out and PTT in.
Line is stereo, should I use the tip? or connect tip and ring?
any comments on how this should be done and how does it work?
73! de Werner OE9FWV
--
Running after women
Maybe I do not understand correctly but why to define PF and macros etc ?
If (suggested) menu item AUTO SPLIT will be OFF all will be as today is.
If (suggested) menu item AUTO SPLIT will be let say 5 (or -3) then ANY
SPLIT activation will cause +5kHz (or -3kHz) offset between TX and RX.
(TX
Hello Werner
My favourite subject! There is currently an issue between the SCS Pactor
modems and the K3, basically the K3 has a TX DSP delay of around 12 mS
and the SCS modems appear to have no post TX PTT delay. I have been
conducting some experiments with Brendan, EI6IZ, on Amtor and have a
Hello,
How can i save the filter selection fl2 for ssb?
I have firmware 2.02.
In CW is all ok.
In SSB my k3 will only select fl1.
In the Config Menu I can select fl2 on in mode ssb.
After changing the mode Fl2 is not selectable.
Thank you.
73 de
Michael DD9WG
G4ILO wrote:
I doubt if that would be possible without redesigning the front panel -
unless it is possible to make the PF buttons take macros comprising
several key clicks.
That isn't necessary. As Lexa has correctly identified, I was thinking
of a firmware option that would do all the
Hi Guys! I wonder if you can help with a bewildering problem please?
I have a K1 with a 4 band board (40, 30, 20, 15m) and the internal ATU. All
function perfectly and match to an inverted Vee cut for 30m. On 30m my analyser
shows a Vswr of around 1.1-1.3.
I have recently added a 2 band board
Julian, Lyle,
thanks for your replies!
Hamsdr magloop tuner is 'simply' an advanced memory device,
helping to reproduce a tuning found once quickly again.
(PLease correct me if I misunderstood it)
I'm still trying to find a magloop tuner which does the same
what I do - searching the resonance,
For his first QSO on his new K3. I then worked him on my K2/100. I sure hope
my K3 brings in DX on my first contact when it arrives!
--
View this message in context:
http://www.nabble.com/K3%3A-Heard-VA3EF-work-AH2L-tp17849319p17849319.html
Sent from the Elecraft mailing list archive at
I am amazed, impressed, and a bit overwhelmed by all of the CONFIG
menu options being added, how to access them, how to navigate the
setup options within any parameter, etc., ala page 50 and so on.
I've done a cursory review of the Elecraft page, but I don't see a
complete listing anywhere; one
Hi, Michael. Perhaps your filter 2 is enabled only for one of the
sidebands. Try using the K3 Utility, configuration tab, Edit Crystal
Filters, and verify that FL2 is enabled for receive in both USB and LSB.
Dick, K6KR
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL
I am trying to get set up for RTTY with an MK2R+ and N1MMLogger / MMTTY.
It seems the line out is dead: I don't get a waterfall on the screen. When I
plug the cable from the other radio in the K3's slot on the MK2R+, I get a
signal. I tested the cable between rig and interface which seems OK.
Is there a web page for these carrying cases?
George Sereikas wrote:
I ordered a carrying case for my K3 from Rose/Ken Kopp and I couldn't
be more pleased. I ordered the version with the 2 extra pockets and it
is a work of art. It was delivered quickly and the workmanship is
Anyone seen it and care to comment? Hopefully Elecraft will get permission to
put it on their website..
Paul
M0CVX
-
Email sent from www.virginmedia.com/email
Virus-checked using McAfee(R) Software and scanned for spam
Hi,
Is there a web site where the list is maintained, that I could see the various
topics and reply there?
Thanks.
Bucky Hydal
Springfield, Mass.
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the
here is a phase discriminator used in a MIL tuner:
http://www.tpub.com/content/antennaandmasts/TM-11-5821-284-34/TM-11-5821-284-340011.htm
Do you think this is what I was looking for?
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
Steve,
Yes, that certainly sounds like strange behavior. Your tuner and
antenna do work on 30 meters because your 4 band board works OK with
them, so they are not the likely cause of your failure.
I can guess that the 'light display/relay chatter' symptom is a result
of the resettable fuse
Can't wait to read the review, and find out if I made the right
choice :-)
73
Stewart G3RXQ
On Sun, 15 Jun 2008 14:16:02 +0100, [EMAIL PROTECTED]
wrote:
Anyone seen it and care to comment? Hopefully Elecraft will get
permission to put it
on their website..
Paul
M0CVX
You made the right choice... Peter is slow off the mark, there are
reviews by ARRL, Rob Sherwood, DL6RAI/DK4YJ, G4ZFE and myself!
The K3 does what is says on the packet, according to my test gear. You
know as well as anyone what the K3 is like from a user point of view, it
has it's quirky
Franki,
Check your connections. Some of the microHAM K3 cables have
the Line In/Line Out (PC In/PC Out) plugs mislabeled. The
3.5 mm plug with the 3.5 mm female jack (used for subreceiver
audio) should be connected to the K3 Line Out jack.
73,
... Joe, W4TV
-Original
http://www.nabble.com/Elecraft-f28632.html
Bob NW8L
On Sun, Jun 15, 2008 at 7:59 AM, Bucky Hydal [EMAIL PROTECTED] wrote:
Hi,
Is there a web site where the list is maintained, that I could see the
various topics and reply there?
Thanks.
Bucky Hydal
Springfield, Mass.
I haven't been able to locate this information in the documentation, so perhaps
a kind soul could oblige?
In anticipation of a K3/100 kit's arrival, I would like to know the length of
power cord supplied and also whether the K2/100 power cable is interchangeable
with the K3/100 (i.e. do the
Can't wait to read the review, and find out if I made the right
choice :-)
Me too. The review is not on the members only portion of the website yet...
Nervous with S/N 2
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a
...whether the K2/100 power cable is interchangeable with
the K3/100 (i.e. do the Andersons have the same orientation
on K2 and K3)?
Yes, they have the same orientation. I initially ran my K3 with my
K2/100 cable.
73,
Lyle KK7P
___
Elecraft
Franki ON5ZO wrote:
I am trying to get set up for RTTY with an MK2R+ and N1MMLogger / MMTTY.
It seems the line out is dead: I don't get a waterfall on the screen.
When I plug the cable from the other radio in the K3's slot on the
MK2R+, I get a signal. I tested the cable between rig and
NAQCC Special mW Sprint Tuesday night!
This coming Tuesday evening will be the Special NAQCC mW Sprint.
You must use 1 watt or less output power. Other stations can use any power.
I will refer you to the proper URL:
http://www.arm-tek.net/~yoel/sprint200806_special.html
There you will find all
So my conclusion is: nothing comes out of the LINE OUT. I looked
through the manual but only found the LIN OUT level parameter which I
cranked up to the max but that doesn't fix it.
I was a bit too fast. I connected a set of PC speakers to the line out and
they let me hear everything. So it's
Lyle KK7P wrote:
Can't wait to read the review, and find out if I made the right
choice :-)
Me too. The review is not on the members only portion of the website
yet...
Nervous with S/N 2
Well the preview news pages sent to affiliated societies arrived last
Thursday so guess
Hi folks,
I've finally had time to recalibrate my K2's KAT2 automatic antenna
tuner module using 25 and 100 Ohm loads on 40m. Please take a look at
my results and let me know if this is typical or if you think I have a
problem.
25 Ω (2.0:1)50 Ω (1.0:1)100 Ω (2.0:1)
1900
Me too, but I realized that the K3 draws somewhat more current than the
K2/100. Depending upon the band antenna, etc., the total current can exceed
the rating of the rating of the 20-amp fuse in the K2/100 power cord.
Ron AC7AC
-Original Message-
...whether the K2/100 power cable is
Two questions for the group because I cannot find the answers in the manual (I
am new to the K3):
1. When you upgrade to any newer firmware version, does it override any of your
calibrations or memory presets?
2. I am a net control station on 40 meters and have strong local stations that
boom
Michael,
I don't believe your results are a lot out of line, but neither can I
say that they are normal.
The diodes used in the wattmeter can have a frequency dependency - that
will be true for both the KAT2 and the OHR WM-2. If the frequency
dependency of the KAT2 is opposite that if the OHR
The review is on page 58 of July RadCom... See:
http://www.rsgb.org/news/radcom/index.php
73 Dave, G4AON
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub,
Kent, you do not specifically need to save any parameters although the
update tool has that facility and it's always worth saving them as it
may avoid you re-calibrating the K3 at some stage. It is important to
tick the always load DSP data tables otherwise the DSP might get
itself in a mess.
Regarding CONFIG AGC SLP, page 50 of the manual:
Higher values result in 'flatter' AGC (making signals at all
amplitudes closer in AF output level).
I use the highest value, 15.
Bob NW8L
On Sun, Jun 15, 2008 at 11:38 AM, kent Angell [EMAIL PROTECTED] wrote:
Two questions for the group because
OK K3 connoisseurs, I've got some more information on my RTTY / line out
problem.
- K3 + line out = OK.
- microHAM hardware and software = OK.
- I tune to an RTTY transmission and have the K3 decode. The tuning aid
tells me I'm right on. I'm not using Dual PB and listen 300Hz wide on a
500Hz
OK K3 connoisseurs, I've got some more information on my
RTTY / line out problem.
- K3 + line out = OK.
- microHAM hardware and software = OK.
- I tune to an RTTY transmission and have the K3 decode. The
tuning aid tells me I'm right on. I'm not using Dual PB and
listen 300Hz wide on a
Solved thanks to Ed W0YK, who told me to see if the K3's FSK pitch matched
the MMTTY mark.
It didn't, now it does and all works fine (3 modes).
My K3 can listen so narrow compared to the TS-850... I think I'm going to
love this rig when it gets hot on HF, expecially on CW.
73 de Franki ON5ZO
Thanks Bob and Dave. I will try your suggestions.
Kent, w7vz
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
I set Autoinfo to Auto1 and it did not seem to cause the K3 to send
out RS-232 data without being polled. My impression is that this is what
this option was supposed to do. I may be out in left field on this, and
if so someone bring me in out of the rain please. :-)
I am trying to get
Ordered Jaunary 12, 2008.
Katie-gram June 7, 2008
Received June 13, 2008.
K-3/100 SN #1058, KPA3, KAT3, KBPF3, KXV3 assembly complete and on-the-air June
15. Now to learn how to drive this puppy. Cheers, Bob, k9foh
___
Elecraft mailing list
Post to:
Is this intended behaviour or a bug?
When I am using coarse tuning mode with CWT enabled and hit the SPOT
button, the search algorithm goes haywire and the transceiver ends up
tuned 5-10 kHz or more off frequency. This is with firmware rev. 0196.
Al N1AL
Be sure Coarse is not turned on.
Hold in the Fine button.
If coarse is engaged, CWT goes crazy when pushing Spot..
Steve Ellington
[EMAIL PROTECTED]
- Original Message -
From: Alan Bloom [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent: Sunday, June 15, 2008 6:57 PM
Subject:
I have a KPA-100 that is not putting out any power. The K2 operates fine
using the standard QRP power (up to 10 watts). Power is good and the SWR
is low. When the power control is advanced to bring in the KPA-100 (relay
click), the power reading immediately goes to 1 and there is no power
Dave,
How is receive with the KPA100 in-line? If receive is degraded, then
the KPA100 LPF may be the problem, but if power output is the only
problem than the PA transistors (or the T/R switch) is the area that
needs attention.
The first step that I would take is to check the bias
Need a little help in setting up my K3 with the navigator interface and mixw
or other softwares.
I have It sending cw without any problem. But I can't get it to send FSK.
When I send a cq it keys the rig and the interface but only get a steady
tone. No FSK. I can use the cat etc. Must have a
Although the KPA is installed and is responding to setup configs, there is
one area that is sometimes overlooked. The internal RF connection to the Main
board needs to be connected correctly, and the antenna needs to go to the KPA
SO239, not the Mainboard BNC.
Al WA6VNN
+++
The build went fine except for mounting the speaker. I think the
supplied fiber and toothed lock washers are too small in diameter for
the width of the speaker mounting slots. It's pretty difficult to keep
them from slipping through the slots, and then the screws go crooked..
I finally gave up and
I plug and unplug serial cables into my PC and K3 all the time without
worrying about powering down either the PC or the K3.
If equipment tended to be sensitive and were damaged by this action it would
be common knowledge, and vendors of this sort of equipment would be have to
deal with many
Good Evening!
It was a wonderful day in the Coast Range of Oregon. Temperature got all
the way into the low 70s. The only clouds I saw were out over the ocean. A
light wind kept the air moving through the house. I had a fire going very low
just to get the chill out of the place and Sam
No problem here with the speaker mounting
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Dick Dievendorff
Sent: Sunday, June 15, 2008 10:23 PM
To: [EMAIL PROTECTED]; Elecraft@mailman.qth.net
Subject: RE: [Elecraft] K3 #1029 Build
I plug and unplug
53 matches
Mail list logo