Hello there
During the first hours of operation on my K2 sn 7063, I noticed that, when
attempting to copy a weak signal, with AFIL 1 on and maximum AF gain, I hear
processor noise. After that, I realized it is everytime I have AF gain in the
vicinity of maximum. I hear it, during reception
Stu
A couple of thoughts.
You didn't mention if the oscillation was occurring with the amp driving an
antenna or a dummy load. The Elecraft transverters have lots of nice features
but they are quite poorly shielded. If you were using an antenna you might be
getting an RF feedback loop
On 5/9/2011 6:32 AM, Steve Kavanagh wrote:
Stu
A couple of thoughts.
You didn't mention if the oscillation was occurring with the amp driving an
antenna or a dummy load. The Elecraft transverters have lots of nice
features but they are quite poorly shielded. If you were using an
Hello:
I just bought an AA-54 RigExperts analyzer. I am tuning a Buddipole
which I use with my K3 (25+ countries and counting).
The RigExpert says my SWR is 1:2.5 at 14.200Mhz. I also scan the SWR
curve with it and I see that I am 1:3 or lower a couple of 100hz
around the 14.200 center
First off let me state that I do not have any of the equipment Stu is
using. The fact the XV432 likes the 50-ohm termination (dummy load
to the rest of us), says it looks like a termination loading
issue. The Henry 2004 should offer a 50-ohm load at input. Some
amps require input tuning (my
I'm so excited. Tracking shows my 500 will arrive in 2 days. YEH!
Phil
Philip LaMarche
LaMarche Enterprises, Inc
mailto:p...@lamarcheenterprises.com p...@lamarcheenterprises.com
http://www.LaMarcheEnterprises.com www.LaMarcheEnterprises.com
727-944-3226
727-937-8834 Fax
Brian,
The consideration over the bulk charge rate is still valid - if the
charger goes into bulk charge state the voltage is higher - AND, if the
receive current is much lower than the bulk charge current, the battery
can be over-charged. To prevent that condition, the bulk charge rate
I took my K3 down to fit a 2nd rx and was reminded of a post by N0SS about
the different way of releasing the rear top corner of the right side panel.
As a reminder, the threaded D-2 block has a threaded pillar attached to it
by a single screw, making it inadvisable to remove the screw at rear
Hi Alexander,
I see this a lot with my K3.
The truth is that the KAT3 is never really out of circuit.
The trick is to enable the KAT3 (Hold ATU Tune), use it to show a low VSWR to
the rigs finals, then disable it (Hold ATU TUNE) again.
You will then find that the VSWR will presented to the rig
Hello Stu2,
Some time ago, I had problems with an oscillating (or at the tip of
starting self-oscillation) XV432. It manifested in such a way, the XV432
being very sensitive to input power levels and jumpy output power when
adjusting the power level. Together with a Mirage D1010 (100W 70cm PA)
On Mon, May 9, 2011 at 6:03 PM, Jeff Cochrane - VK4BOF
vk4bof.elecr...@gmail.com wrote:
Hi Alexander,
I see this a lot with my K3.
The truth is that the KAT3 is never really out of circuit.
The trick is to enable the KAT3 (Hold ATU Tune), use it to show a low VSWR
to the rigs finals, then
TJ,
If you are doing it for the first time, give yourself 8 to 12 hours for
the whole task.
As Alan Wilcox has said, use Specrtrogram for alignment, and become
familiar with its use beforehand since you have a deadline. The use
of Spectrogram 5.17 (and its download) is available from Tom
As a confidence building exercise, try it into a dummy load rather
than the amp. If it works into the dummy load, blame the input if the
amplifier.
73,
Don W3FPR
On 5/9/2011 6:22 PM, Alexander Sack wrote:
On Mon, May 9, 2011 at 6:03 PM, Jeff Cochrane - VK4BOF
vk4bof.elecr...@gmail.com
Don,
I'm sorry but I fail to understand why you think that the bulk charge mode will
overcharge the battery.
Properly configured, the smart charger won't even completely charge the
battery in the bulk mode, it takes a shift to the higher voltage absorption
(overcharge) mode to completely top
Elecraft K3's mentioned repeatedly in the results of the 2010 Stew Perry
contest:
http://web.jzap.com/k7rat/2010_Stew.htm
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I'm running P3 firmware 1.05.
If I have my SubRX enabled and the two receivers tuned to two different
signals, my P3 cursors are displayed exactly as expected. If I then hit
BSET, the P3's VFO A cursor and display (including the displayed VFO
frequency) shift to the VFO B frequency, despite the
I had a similar problem with my XV432. I was able to chase the problem to the
tx
driver stage. The fix was to add ground vias from the top to the bottom of the
board in a few judicious places. I passed this info back to Gary at Elecraft. I
know of at least one other XV432 that has been
Hi Stan,
I turned on my KRX3 and BSET. My P3 display did not show the VFO B frequency
and the cursor remained with VFO A. When I pushed ALT, VFO B did change to the
opposite sideband as expected. Roy Morris W4WFB
__
Elecraft mailing
I think that the aberrant BSET behavior only occurs when the diversity
mode is on. This is related to the front panel display (and the SUB
receiver) switching over to VFO B during BSET, but I don't see it when
not diversity.
73, Guy
On Mon, May 9, 2011 at 9:11 PM, Roy Morris
During the 7QP this past weekend my KDVR3 Digital Voice Recorder would upon
occasion provide no audio while the transmitter was keyed. I was using N1MM
Logger and I do not recall doing anything that might have interrupted the KDVR3
Digital Voice Recorder such as tapping my foot switch while
Just received and put KPA500 #24 on the air today. Wow! what a great product
and well worth the wait. I drooled over it at Visalia and it’s just great to
get to put one on the air. Thanks to all the people at Elecraft that made this
possible and produced such a great amplifier. It fits
I confirm the bug when in fixed-tune mode. I'll add it to the list,
thanks.
Alan N1AL
On Mon, 2011-05-09 at 17:19 -0700, Stan Gibbs wrote:
I'm running P3 firmware 1.05.
If I have my SubRX enabled and the two receivers tuned to two different
signals, my P3 cursors are displayed exactly as
Steve,
I had the same problem, though it was intermittent. In my case, once the
radio heated up the recording would be truncated, first a little, eventually
playing only the first couple of seconds.
Elecraft swapped out the KDVR, and it's been OK since.
(OT - I spent many hours riding my
23 matches
Mail list logo