Jack,
You will need the new synthesizer - two if you have the KRX3.
You will also need the KBPF3A. If you already have a KBPF3, there is an
upgrade kit that you can install - the KBPF3MDKT (see K3 Parts and Mod
Kits).
You will also need the KXV3 (or KXV3A or KXV3B) option in your K3
because t
Don's procedure in his doc works great. But there is a gotcha that I
don't recall being covered.
The ALC meter algorithim "beats" with certain tuning tones and when that
happens, it makes the ALC meter ramp up and down in a fast oscillation.
This has been discussed on this list relatively recen
On Sun, Oct 1, 2017 at 5:30 PM, Lynn W. Taylor, WB6UUT <
kx...@coldrockshotbrooms.com> wrote:
> Just saw an ad for Genie LED Bulbs.
>
> Apparently some LED light bulbs make enough noise that they desense the
> garage door receiver.
>
> These bulbs are specifically low-RFI.
>
> I have no more infor
How ironic. My two Genie garage door openers sit there and generate a huge
amount of buzz-saw hash on HF as long as they have power. I have to
essentially unplug them to use the radio, and my horizontal loop is 100
feet away from them.
Chip
AE5KA
On Sun, Oct 1, 2017 at 5:30 PM, Lynn W. Taylor, WB
Hello,
Because most of my operation has been remote lately, I am selling one of my
two K3 transceivers. Both are in superb condition. I only need one and
will be keeping the one that does not sell.
If interested, please contact me off list and I will send you the specs for
both. The serial numb
Perhaps this is a software problem, but I thought I'd start here. Using K3
(s/n 68xx), SignalLink USB and WSJT-X. Everything works fine on FT8 on all
bands but 17 & 30. I can decode on those bands, but there is no xmit. The
rig keys OK and goes into xmit but there is no output. Radio performs
If split is on, make sure software did not set tx freq out of band.
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.
I used my K3 on 495-502 KHz as an experimental station. I got 1mw
output at the XVT Tx output jack running the TEST mode.
For amplifier, I bought a surplus Southern Avionics NDB (aircraft Non
Directional Beacon) transmitter. It is a xtal controlled oscillator
amplified to 100w into 50-ohm lo
How much SSB do you do on 30 meters?
I'd start by re-checking the Data/submode on the two bands.
Sent from my iPhone
...nr4c. bill
> On Oct 2, 2017, at 6:03 PM, Mike Baird wrote:
>
> Perhaps this is a software problem, but I thought I'd start here. Using K3
> (s/n 68xx), SignalLink USB and
Interesting question. But I doubt W0RSR operates SSB on 30 :) Or I hope he
does not. A better question would be what software are you running, and on
which operating system, e.g., Windows, MacOS or linux? Since WSJT-X is the
only software package I know that supports FT-8 I doubt it is a rad
The SWR bridge on my K2/KPA100 had been working perfectly for years, but I
apparently blew something while making comparison measurements with a
friend's K2 I was trying to fix. Now the K2 panel LCD SWR indicator reads
around 5:1 for a near-perfect dummy load. Adjusting C1 makes almost no
differen
Dick,
Make certain you have the diodes D16 and D17 mounted the right way around.
Replace the coax jumper to the dummy load - measure your dummy load with
your ohmmeter to be certain it is a good 50 ohm dummy load (yes, dummy
loads can fail).
Then balance the wattmeter. Easiest way is to pow
12 matches
Mail list logo
