No transformer needed. The gain settings on page 55 of the manual are
sufficient for the SM 58. Just wire it as an unbalanced output. I
use both the rear or front MIC inputs with no issues and a variety of
different mikes.
73
Bob, K4TAX
On 10/4/2017 12:18 PM, Stewart wrote:
OK here's
No preamp required. Set the Mike gain via the menu to high. Easy to
wire the mike XLR to an unbalanced circuit. Pin #1 & #3 to ground and
Pin #2 to MIC high. See page 55 of the manual [MIC SEL] for details.
If you close talk the mike it will be bottom end heavy. Typically no
closer than 4
It took Keith at the mothership a bit of coaching effort to get me out of
the problem of not being able to post.
Don't understand what the problem really was.
Something to do with a long-unused email acct.
At any rate, I trust it's gone for good.
Brgds, Dave, N3HE
--
Sent from: http://elecra
Dsvid..your posts are reaching the reflector just fine, all of them are now
safely in all of the hundreds if not thousands of reflector subscribers'
in-boxes.
73-Gary K9GS
Original message From: David Windisch
Date: 10/5/17 3:38 PM (GMT-06:00) To: elecraft@mailman.qth.net
reply works
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list host
yatest can't seem to get past the test stage
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecra
Hi all concerned:
Since my hamming will be thru a remote site shortly, I am selling a
venerable Elecraft station.
I am the owner now, but not the original purchaser, of the equipment, and
have _not_ modified any of it.
All units are in working order and good physical condition, and come with
neede
Hi all concerned:
Since my hamming will be thru a remote site shortly, I am selling a
venerable Elecraft station: _K3_ xvcr, KPA500 amp, KAT500 tuner, P3 display.
I am the owner now, but not the original purchaser, of the equipment, and
have _not_ modified any of it.
All units are in working order
ignore
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by
test
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
Just seeing if this makes it through
72
Myron
WVØH
Printed On Recycled Data
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
Thi
Hi Stan:
Post ten.
There are two ways to approach this, just put something up, or measure
and optimize. When using the KX3 ATU, both methods will provide similar
results.
An 88 foot Doublet and feedline is modeled using EZNEC and SimSmith. The
results found here:
http://www.kn5l.net/Doublet88/
12 matches
Mail list logo