Good Evening,
The annual Field Day hiatus has passed. It has been cool and wet.
But, then, it is not yet officially summer in Oregon. For that you have
to wait until after July 4th. However, the loggers have been very
active. They're clearing the other side of the top of this
A Mortty will do a great job of conveying the ASCII data stream to Baudot,
generating the FSK data you need.
Then, take a look at N6TV’s Y-Box for an easy way to connect the data into the
Aux IO connections.
The Mortty is $18, available at: http://hamprojects.info/mortty/
I use a MicroHAM DigiKeyerII with a premade cable for my K3S on FSK
RTTY. http://microham-usa.com/store/product-info.php?pid2.html It is
close to plug and play and it has worked well for me.
John KK9A - W4AAA
Kevin, N4TT wrote:
I'd like to use FSK-D. I've read over the options and
If I use a large power supply and turn the KX3 on its side and shake it - I
still only get 15 watts according to my Tird meter (Trusty ole Bird).
Hank
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Wayne Burdick
Sent: Saturday, June 29, 2019 4:15 PM
To: JP
That gentleman is mistaken unless something happened while I was not
watching, the KX3 does up to 15 watts.
73,
Don W3FPR
On 6/29/2019 4:04 PM, JP Douglas wrote:
Hi all!
While having a QSO yesterday from my mobile to a QRP station on 20 meters, the
gentleman I was chatting with mentioned
Not.
Wayne
> On Jun 29, 2019, at 1:04 PM, JP Douglas wrote:
>
> Hi all!
>
> While having a QSO yesterday from my mobile to a QRP station on 20 meters,
> the gentleman I was chatting with mentioned that the KX3 now does up to 20
> watts of power. Never heard this before and wondering if
Hi all!
While having a QSO yesterday from my mobile to a QRP station on 20 meters, the
gentleman I was chatting with mentioned that the KX3 now does up to 20 watts of
power. Never heard this before and wondering if it's true, currently my KX3
does up to 15 watts. I use my KX3 mostly for
No. And a USB cable won’t work. You need an interface that takes the TX from
aerial port to the FSK pin on ACC port. You can use a splitter here. Avail from
Elecraft.
Signal to ACC FSK pin must be T level(need for interface).
Sent from my iPhone
...nr4c. bill
> On Jun 29, 2019, at 2:28
Dave,
Go to CONFIG and check your L-MIX-R settings
73
Frank
W3LPL
- Original Message -
From: "Dave Weiss"
To: elecraft@mailman.qth.net
Sent: Saturday, June 29, 2019 5:52:43 PM
Subject: [Elecraft] Diversity Receive setup??
Hi All:
I have a BOG loop setup with 30 Feet per
I'd like to use FSK-D. I've read over the options and would like to use a
USB to ACC cable. The ACC socket on the K3s is being used by the KPA/KAT
combo.
Is there an off-the-shelf kit of cables/interrupters I can get that would
be plug-n-play for FSK-D on a K3s + KAT + KPA?
73,
Kev N4TT
Greg,
The Elecraft power control is done in the RF stages and not the audio.
After a band change or a change in the POWER knob, the power control
loop is reset.
The response time is quick enough that you do not notice it in normal
operation, although it does take a dot or two in CW or a couple
Hi All:
I have a BOG loop setup with 30 Feet per side of 50 OHM RG213 (4 Sided)
into a 2 to 5 transformer. I have fed this signal into my K3 with KRX3 set
to ANT=BNC and ANT1 RX PRE indications on the front Panel and DIVERSITY
RECEIVE as well. I have selected a Broadcast Radio station WOR 710 (
Don Wilhelm writes:
> The above method works fine for many transceivers, but NOT for
> Elecraft which measures the actual power output, compares it with the
> set power and adjusts the RF drive accordingly. This is a fully
> closed loop system. As far as I know, Elecraft is the only amateur
>
Dennis,
Impedance matching in audio circuits has not been important since the
days of vacuum tubes with audio output transformers.
Were you operating the KX3 on batteries when you found that oscillation?
If so, the internal resistance of the batteries would be the cause of
the oscillation.
Dennis..
I've had very good results from the several West Mountain
COMspkrs I have.
73!
Ken Kopp - K0PP
On Sat, Jun 29, 2019 at 11:01 AM Dennis via Elecraft <
elecraft@mailman.qth.net> wrote:
> I searched the KX3 manual and could not find a specification for the
> headset/speaker output jack.
I searched the KX3 manual and could not find a specification for the
headset/speaker output jack. Last weekend at Field Day I plugged in a low
impedance speaker and got some oscillations above a certain output level.
I want to optimize the impedance match to my computer for FT8 and also know
Each command must be terminated with a semicolon.
73 de Dick, K6KR
> On Jun 29, 2019, at 05:48, "p_hippenme...@bluewin.ch"
> wrote:
>
> hi all
> i can't find a command or macro to scan (frequency scan) with audio ON.
> «SWH10;» works nice, but audio is muted.
> «AG» and «SQ» commands have
hi all
i can't find a command or macro to scan (frequency scan) with audio ON.
«SWH10;» works nice, but audio is muted.
«AG» and «SQ» commands have no effect.
tnx fer help!
73, paul
hb9axl
__
Elecraft mailing list
Home:
Hi
A minor error in the newsletter article on the WWVB, should be 60kHz.
Chris
VK2ACD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
19 matches
Mail list logo