Hello Ed,
Lately, I've noticed my 3-year-old KX3 drifts a small amount, according to
the readout, in CW mode. For instance, if I set rig on 7.033.00 hit the key
and look at the readout it will say 7.033.010 and sometimes bounces back to
7.033.00
I don't remember this being a problem before. Is
Lately, I've noticed my 3-year-old KX3 drifts a small amount, according to
the readout, in CW mode. For instance, if I set rig on 7.033.00 hit the key
and look at the readout it will say 7.033.010 and sometimes bounces back to
7.033.00
I don't remember this being a problem before. Is this normal f
Good evening all,
When I powered up my KX3 this evening, it displayed ERR 2M on VFO B and d=004
on VFO A. If I turn off the 2m transverter in the configuration menu, the unit
powers up without error.
I pulled the back and reseated the ribbon cable. This did not correct the
issue.
I’m lookin
Lou,
If FedEx required a signature, I can guess at the problem. Everyone at
Elecraft who can work remotely are observing a shelter-in-place
directive. That would include the front office folks and support and
anyone else who can work remotely.
UPS or USPS shipping may be the best choice in
I sent my KPA500 in for service on 2/28, and they shipped it back to me on
3/13.
I received it today. Very happy about that!
(UPS is actually waiving all signatures, so just a 'Thank You' sufficed.)
73
Lyn, W0LEN
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraf
Any available?
Mike
AI4NS
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help su
Sent my KX2 back last week for repair, and got a notice from FedEx of a
delivery exception: "Local delivery restriction, delivery not attempted."
Although it's scheduled for delivery tomorrow, that can't happen. FedEx told
me it will be returned to me after 10 days if it can't be delivered. Minor
My work has been published for ten years, the most current work for two
years, and there have been millions of downloads.
73, Jim
On 3/18/2020 12:29 PM, Lyn Norstad wrote:
so I am sure they would welcome your expertise.
Perhaps you should make your services available to them.
_
Hi Bob,
On 3/18/2020 7:18 AM, Bob McGraw K4TAX wrote:
On point #2, the balanced feed line is twisted at my installation. This
is one advantage to the vinyl covered line. This makes essentially a
twisted pair which Bell Labs many years show is a way to minimize
induction into the feed line.
On 3/18/2020 5:39 AM, Lyn Norstad wrote:
I have a hybrid 4:1 / 1:1 balun at the shack end of the balanced
feedline and have absolutely no issues.
Hi Len,
The problem is noise pickup on the line. I think I remember that your
QTH is relatively isolated, hence not much local noise. The other
q
I have to agree with Lyn on several points. I do agree the directional
pattern is different on every band. For me, that suffices as I am not
one to aggressively chase DX. If you need specific directional
patterns, then other considerations for antennas should be undertaken.
On point #2, t
Jim -
Your comments are well taken ... but mostly invalid for my installation.
For example -
1)Their directional patterns are different on every band;
Exactly, and this plays perfectly into my coverage needs. For example, I
need (and designed for) 80 meter coverage concentrated
I wonder. Wouldn’t such noise be out of phase on the two halves of the flat top
and hence be rejected?
Also, the nulls will be in the same directions (although the tightness of the
pattern will vary) when the antenna is operated from half its design frequency
to twice that (e.g., from 40 to 10
13 matches
Mail list logo
