On 7/22/2021 8:01 PM, Steve Hall wrote:
Dave,
Thanks for checking into the 40 meter SSB net. Hope to hear you regularly
on the net.
Eric, WB9JNZ relayed you in, as the conditions were very difficult and I
could not hear you directly.
Steve, WM6P
Thanks Steve,
And thanks Eric for the relay. H
Dave,
Thanks for checking into the 40 meter SSB net. Hope to hear you regularly
on the net.
Eric, WB9JNZ relayed you in, as the conditions were very difficult and I
could not hear you directly.
Steve, WM6P
__
Elecraft mailing list
Home:
Hi,
I keep getting kicked off the reflector for the stated reason of too
many bounces. How come no other list seems to have this problem?
I'd love to stay subscribed to the list but re-applying is becoming too
onerous.
Is there anything we can do to remedy this problem?
Sincerely,
Eric F
Hey y'all, I have an old K3 that we upgraded to K3S a few years back. It
also has a DVR unit in it. All firmware is current.
Today upon powerup the DVR didn't work - showed as not installed and
obviously didn't work.
I powered off the radio and back on again, and there was the DVR, working
again
I'm in general agreement with Bob, but there are some details.
(1) You don't want to melt you power supply wires. If you trust
the power supply device to properly current limit, then you
don't need a fuse. If you are using something like my old
solar/deep cycle battery supply, you definitely n
Hi
How are you doing, I want to ask you for an assistance
Do you normally order from amazon?
Thanks.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elec
It appears the problem is more deep-seated.
I’m away /P right now and decided to do some FT8 using a Raspberry Pi. I set up
the Tx drive (seemingly) OK, by pressing Tune on WSJT-X and adjusting Tx level
and Mic gain to get the right amount of ALC.
However, when I then try to Tx again, TX LED lig
The board is definitely not happy. I plugged the aux cable into my KPA500
and as I cycle through the bands I keep getting invalid on the KPA500 screen
when it comes to band. I have a call into Elecraft support.
Pete Chamalian, W1RM
w...@comcast.net
-Original Message-
From: elecraft-bou
With that power supply, which has both good over voltage protection and
current limiting, adding fuses in the DC line will add resistance to the
line. Even being a small amount, it will affect voltage regulation from
no load to rated load at the radio. For this reason I do not
recommend add
Hi Ray,
Are you currently using a 25 amp? If so, have you had any issues with
that, and are you running P3/SVGA, etc?
25 amps seems quite close to the rated current draw of the K3. I
believe the K3 can draw 22 amps on full power, and as Jim said, other
items all add up.
I also mentioned
Thanks guys.
de Doug KR2Q
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help su
Down here also John (several days now).
73, Bill W4ZV
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: htt
On 7/21/2021 10:49 PM, Rick NK7I wrote:
25 amp fusing isn’t a lot over overhead for a K3 with KRX3, KIO3a, P3 with the
SVGA board and the PR6-10 preamp in play.
A study of fuse (and breaker) specs is worthwhile. In general, fuses are
rated by average current, with considerable allowance for s
13 matches
Mail list logo