[Elecraft] FS: KXAT1 built

I am selling my KXAT1. The unit is built and ready for use. Comes with original manual. Asking $70 Contact off list for pictures or more info. jspo...@yahoo.com Thanks -- View this message in context: http://elecraft.365791.n2.nabble.com/FS-KXAT1-built-tp7560410.html Sent from the Elecraft

Re: [Elecraft] KX1 ATU low power

SN 2626 is toast. 73 -- View this message in context: http://elecraft.365791.n2.nabble.com/KX1-ATU-low-power-tp7558478p7558756.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman

Re: [Elecraft] KX1 ATU low power

Oh well, so much for help -- View this message in context: http://elecraft.365791.n2.nabble.com/KX1-ATU-low-power-tp7558478p7558720.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mai

[Elecraft] KX1 ATU low power

Just finished the ATU module for the KX1. Relays all work and swr into the DL1 is r 1.0 on all bands. Power output though is limited to about 2 watts per the display. Minus the the ATU, the W1 says I am getting 3 watts into the DL1 on all bands except 80M where it is 4 watts. Regulated bench

Re: [Elecraft] KBX30/80 Module

Using a different RF probe and meter, I re read the output of my KX1 using a 12 volt battery as a source: 3M 12.02 volts 7M 10.17volts 10M 10.3 volts 14M10.2 volts I think this is a close as I am going to get. I have tried moving the coils around the L2 torioid, but the figures do not get better

[Elecraft] KBX30/80 Module

I have finished installing the KBX3080 module along with the power module. Things appear to be going well, but I did note that when I took a reading with my VTVM and RF probe on the antenna output, my readings on 80M were quite a bit higher than on the other frequencies. 80M 6.6 volts 40M 5.2 vol

[Elecraft] KX1 Power level

"What is your DC voltage? The KX1 specification is 3-4 watts with 12 volts, so you are close to the spec right now. If you have an antenna analyzer, check you dummy load to be certain it is the same 50 ohm pure resistive load on both bands. Your wattmeter may also be frequency sensitive - many a

Re: [Elecraft] first post test and kx1 power issues

My bench voltage is 14 volts and battery is measured at 12.4 VDC Tried a new and better dummy load and got 3watts on both bands with bench supply and 2 watts on 40M and 3 watts on the battery. I used an RF probe on the output with the battery supply I got 5.6V on 14M and 5.3 on 40M These are p

Re: [Elecraft] first post test and kx1 power issues

I have just assembled s/n 2626 and have found low power output. Mine is a two band version with no options. With a bench supply, I get 4 Watts on 20M and 3 Watts on 40M into a dummy load. This measured with an electaft W1. I will look again at my LP toroids, but looks like I may need to do the po

Re: [Elecraft] first post test and kx1 power issues

I have just assembled s/n 2626 and have found low power output. Mine is a two band version with no options. With a bench supply, I get 4 Watts on 20M and 3 Watts on 40M into a dummy load. This measured with an electaft W1. I will look again at my LP toroids, but looks like I may need to do the po