$10. A search for the terms USB CI-V will find them.
I've used one on my ancient 735 and it works well.
73,
Dave
KW4M
-
Dave
My Web Site
--
View this message in context:
http://elecraft.365791.n2.nabble.com/kxusb-question-tp7630404p7630407.html
Sent from the Elecraft mailing list
a relay click when
this happened.
This happened on multiple occasions. Subsequent transmissions were fine
until another significant QSY.
The CW keying was computer-generated at 25 WPM.
-Dave
KW4M
wayne burdick wrote
> Ralf,
>
> Like the K3's ATU, the KX3's ATU stores up to 32 segments o
Not counting Field Day outings with the local club, my first camping radio
excursions were with a Heathkit HW-104 powered from a gel-cell battery about
the same size as a car battery. Needless to say, I didn't set up camp too
far away from the car! But it was rather nice to have a
The weight of a KX2 with no battery or installed options is specified to be
13 ounces.
What are the individual weights of its various options?
I'm trying to estimate the potential weight savings compared to a KX3 with
options installed.
"Worry about the ounces and the pounds will take care of
/I want to operate psk with the kx2 using a computer./
I'd be happy with just CW
...if only that radio existed.
:)
73,
Dave
-
Dave
My Web Site
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Advice-on-software-tp7603589p7603603.html
Sent from the Elecraft
:)
Yep!
-
Dave
My Web Site
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Dayton-Update-tp7602571p7602679.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home:
It's a good idea to check the resistance of any used dummy load, especially
one that has some age on it.
The resistance of my 30+ year old Heath Cantenna gradually reduced to 42
ohms. This was enough error for the power meter to indicate a potential
transmitter problem.
W1GA is selling
Agreed. I had to make a mount for mine.
See here. http://www.genebitsystems.com/david/MotorolaSpeaker/index.htm
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Phonema-Speaker-for-K3-tp7592810p7592845.html
Sent from the Elecraft mailing list archive at Nabble.com.
For most normal means of transportation this is not an issue.
However, I have experienced this exact failure mode in radios and a
switching-mode AA battery charger while traveling on my motorcycle, which is
certainly a high vibration environment. I've found that glue from a hot
melt glue gun
And here's a third.
I built one of Weber's ATS-3B kits and use it on occasion, such as during
Field Day 2011.
http://www.genebitsystems.com/david/HamRadio/FieldDay2011/FieldDay2011.htm
The demand and popularity of his kits is evident as the last run of MTRs
sold out literally hours after it
I am also a single lever paddle user. There must be others who also prefer a
single lever paddle over dual lever paddles.
It would be nice if a single lever paddle version of the KXPD3 was
available. I don't own a KX3, at least yet :), but this might be enough to
push me off the fence.
Sorry
The project is at that awkward point where more than a few prototypes are
desired but likely not enough to enable a reasonably priced production run.
Ideally someone with resources beyond mine would want to pick it up at some
point if the numbers are there to justify it.
ExpressPCB's advice
It does not have to be that expensive.
The boards can be purchased using their 4-layer MiniboardPro service. The
current cost is $98 plus $9.85 shipping for three identical panels.
Each panel contains three MAB boards. So the cost per MAB board would be
$11.98.
I used a shear to cut out the
Some minor changes have been made to the project manual, mostly in the parts
procurement section as related to the J1 connector.
For those persons who decide to build one, please make note any problems,
points of confusion, potential improvements, etc. and provide them to me via
email. I intend
I don't know how many boards Tom has left, but the Mouser project link is
included in the pdf project manual.
Here it is:
http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=4954c48ac1
http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=4954c48ac1
--
View this
panel board.
Two microphone connector pins are used to bring the fixed-level audio output
and the CW keying signals outside the radio.
Complete details can be found here.
http://www.genebitsystems.com/david/K2MiscAccessoryBoard/index.htm
73,
Dave
KW4M
--
View this message in context:
http
All prototype boards have been spoken for.
For those who have expressed interest in purchasing one, you will be
individually notified regarding your status.
Final status will not be known until all payments have been made as there is
a chance someone will back out.
Thank you for your interest!
I have a K2/100 that I would like to occasionally configure as a lighter
weight qrp K2. So I'm looking for the base model top cover and speaker.
If you have one you're interested in selling, please contact me off the
list.
__
18 matches
Mail list logo