I use the unit in the link below and it is quiet. I keep my K3 battery bank
with a 100w panel connected to keep the system ready to go.
http://ki0bk.no-ip.com/~pwrgate/LLPG/Site/Solar.html
~73
Don
KD8NNU
2014 3905CC Top Gun :-)
-.- -.. ---.. -. -. ..-
I have Direct TV with no RF issues.
~73
Don
KD8NNU
2014 3905CC Top Gun :-)
-.- -.. ---.. -. -. ..-
-Original Message-
From: John K9UWA
Sent: Tuesday, May 17, 2016 6:03 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] RFI and Direct tv or Dish network
I just posted a similar question on the Topband and Ham Antenna reflectors.
I am considering the same antennas for my QTH and adding a second receiver
to the K3.
I find that I am RX limited compared to signal reports that I get that are
not just the 59 contest mode. So for me this will be a
I had the fortunate experience to work Jim during the contest and yes he had
a nice clean signal.
With the settings on my K3, Heil IC mic and SGC power cube I had multiple
comments on my signal and how nice it sounded. It felt good to have busy
contesters make such a statement.
Right
I use a cobweb at 40ft and it works real well for me also. It’s a good
multiband antenna.
~73
Don
KD8NNU
2014 Top Gun :-)
-.- -.. ---.. -. -. ..-
-Original Message-
From: drewko
Sent: Sunday, September 14, 2014 8:43 AM
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] OT:
I don’t get the whole ergonomics thing as I find the radio easy to use.
Its way easier than my IC-7000 which is a small radio but has way more
layers of menus.
~73
Don
KD8NNU
-.- -.. ---.. -. -. ..-
-Original Message-
From: MontyS
Sent: Thursday, April 03, 2014 6:13 PM
To: David
Interesting as I had a similar problem with my unit on 160m this weekend.
Turned out as I went higher in power I was burning thru an insulator on my
vertical. Thus my problem occurred at higher power until my insulator was
totally gone. Then it was easy to find.
I suspect that that
Does anyone know how to convert the VFWD readings from the KAT500 software to
actual watts out?
If I knew this reference calculation then I could eliminate my W2 from the
system. I guess I could do lots of measurements to get close but if some knows
and can share it would be a lot quicker.
Look for an SGC powercube. I have one and it works well, you need to find
a used one. They may be starting to make them again shortly.
~73
Don
KD8NNU
-.- -.. ---.. -. -. ..-
-Original Message-
From: mikefur...@att.net
Sent: Sunday, August 18, 2013 4:14 PM
To:
Gents,
I wish to get a new computer for the shack and want to have one that is RF
quiet and has real serial ports.
I am guessing that others have purchased some PC’s recently and would have some
suggestions on some that are HAM friendly with a K3.
I use a K3, KAT500, W2 and HRD for rig
I think the rain and fog has gone to their heads. LOL
~73
Don
KD8NNU
-.- -.. ---.. -. -. ..-
-Original Message-
From: David Christ
Sent: Tuesday, July 23, 2013 7:39 PM
To: Elecraft Group
Subject: Re: [Elecraft] [K3] Audio circuit distortion
I haven't laughed so hard in a long time.
I have noticed since the last update of software I am getting more retuning
also.
I had been running a test version prior to that and it did not exhibit the
same retune as often. In fact I did a tune or train check prior to the
contest yesterday by going thru the bands and pressing tune to
Mine works great and comparing readings to my other equipment it appears
spot on. From barefoot low power on the k3 to my amp on. I use the peak
function all the time as I do a lot of SSB and it just makes me feel good.
I have the 2kw sensor.
It also helped me on 6m as I was running the
I do run two monitors already I guess maybe I need to get bigger ones. :-)
I am not a programmer so I do not know what the limitations are for
shrinking the windows to smaller sizes. So if it can not be done based on
how the software is written then it is what it is.
~73
Don
KD8NNU
-.-
I did purchase a hat at Dayton yesterday.
Maybe we can convince Elecraft to work with one of those suppliers who do
hats and allow us order direct and then we could get our Call Sign added at
the time of purchase.
I know this can be done. Then Elecraft does not have to bother directly
with
15 matches
Mail list logo