[Elecraft] Case for XG2

Can any one suggest a case for the XG2 Joe W1JGS - Joe W1JGS -- View this message in context: http://elecraft.365791.n2.nabble.com/Case-for-XG2-tp5685861p5685861.html Sent from the Elecraft mailing list archive at Nabble.com. __

[Elecraft] Windows 7 32 bit

Does anyone know if the K3 utility and K3_EZ are compatible with 32 bit Win 7 Joe W1JGS - Joe W1JGS -- View this message in context: http://n2.nabble.com/Windows-7-32-bit-tp4441435p4441435.html Sent from the Elecraft mailing list archive at Nabble.com.

[Elecraft] [K3] K3 Diversity Receive

I am in the process of setting up a diversity receive configuration with the subreceiver. I usually run about 600 watts. All my antennas are horizontally polarized; an E-W 160M Carolina Windom, a N-S Carolina Windom and a tri-bander yagi Can any one give me some guidelines about suggested

[Elecraft] Memory Problem

I am trying to use M1-M4 for frequency recall (DVR not installed). I pick a frequency, tap VM, TAP M1. I then put in a new frequency, tap MV and tap M1. I then see a message NOT SET with no frequency change. Can anyone tell me what I am doing wrong Joe W1JGS - Joe W1JGS -- View this

[Elecraft] [K3] K3 ACC Connector

Hello all I just purchased an Ameritron ALS-600 amp which does band switching. For bandswitching, they suggest interfacing it with the K3 through their ARI-500 ( for cabling reasons). This set up for the K3 uses the ACC LP Key Out pin to key the amp...not the Key Out RCA jack. The Amp will not

[Elecraft] [K3] For Sale: Higher Power Antenna Tuner for K3

If you use an amp with your K3, you will need a higher power ATU. I have an MFJ-993B 300 Watt Intelli-Tuner for sale. Unit is in like new condition with original manual. This is a great auto tuner, easy to use and probably one of the best units MFJ sells. Unit handles 2 antennas, has lots

[K3] [Elecraft] High Audio

I am using FW 2.76 no preamp, RF gain at 2-3 oclock and a Heil headset. On SSB audio level is consistently very high. I have to turn audio gain to 9-11 o'clock to listen comfortably Is there a setting I am missing - Joe W1JGS -- View this message in context:

Re: [K3] [Elecraft] Audio at startup

I have done some research on this issue and the thread Loud audio blast on power up is actually the same problem. Is there a fix Joe G wrote: K3 #2120 Firmware 2.67 On SSB and all bands, at startup audio is low (can still hear signal) and after about 2 seconds it increases

[Elecraft] Previous Firmware

Where can I find copies of previos versions of official firmware - Joe W1JGS -- View this message in context: http://n2.nabble.com/Previous-Firmware-tp1655018p1655018.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft

[K3] [Elecraft] Audio at startup

K3 #2120 Firmware 2.67 On SSB and all bands, at startup audio is low (can still hear signal) and after about 2 seconds it increases. This happens when AGC is either fast or slow. I have turned RF Gain up to max and it still happens intermittently. Can somone give me some guidance - Joe

[K3] [Elecraft] K3 Utility

I use two Com ports on my computer: one for my logging program (DXLab) and the other for my rotator control Does the K3 utility require a third com port and, if it does, how do I get it ...since I have used all my ports - Joe W1JGS -- View this message in context:

[K3] [Elecraft] Initial Settings

S/N 2120 is built !! I am now in the process of setting up the controls for initial SSB tests. For Xmit Waynes suggestions are great For Rcv I could use some suggestions ie RF vs AF settings, NB, NR, etc Thanks in advance - Joe W1JGS -- View this message in context:

[K3] [Elecraft] ALS-600

Could someone tell me hoe to hook my ALS-600, Relay and ALC outputs, ro the K3 - Joe W1JGS -- View this message in context: http://n2.nabble.com/ALS-600-tp1562093p1562093.html Sent from the [K3] mailing list archive at Nabble.com. ___ Elecraft

[K3] [Elecraft] Power meter

Can anyone suggest a good power meter to calibrate the K3 Joe W1JGS - Joe W1JGS -- View this message in context: http://n2.nabble.com/Power-meter-tp1211374p1211374.html Sent from the [K3] mailing list archive at Nabble.com. ___ Elecraft mailing

[K3] RE: [Elecraft] Power meter

All Thanks for the input Joe W1JGS _ From: W6NEK [mailto:[EMAIL PROTECTED] Sent: Saturday, October 04, 2008 2:56 PM To: Joe G Subject: Re: Power meter Hi Joe, The last I heard, Elecraft uses the Telepost LP-100 Vector Wattmeter to calibrate factory assembled K3's

[Elecraft] Prospective K3 Owner

Well, if all goes well, I will have my K3 by Christmas. Needless to say, I have begun reading and planning so the building of the kit comes off without a hitch I would appreciate any suggestions anyone could offer. Specifically, - Are there any tools, over and above those mentioned in the