Is anyone using ESSB? If so, can you listen to SSB using the AM filter set
say to 3.5 width but transmit on the 2.7/2.8 filter?
Mike
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.
I have the 2.8 kHz filter in the main receiver and want to supplement that
with either the 2.1 kHz or 1.8 kHz filter. A friend who has the 1.8 thought
is was too narrow. What are you guys using? Anyone have all three?
Mike, W4UM
__
Is anyone using the 1 kHz filter in the K3 subreceiver for CW? Any pros or
cons?
Mike, W4UM
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@m
I recently picked up a used THL 500V 2M amp. I want to drive it with my K3,
which has no 2M capability. The K144KV-F internal 2M module only has 10 Watts
output, which is not enough to drive the THP 500V to 500 Watts. The KV144 2M
transverter has enough power to do it, but it has to be extern
Anyone using this combo with the ACC (15-pin) instead of the mic jack? DX
Engineering, and well as TigerTronics, sell all kinds of pre-made cables but
only a mic cable for the K3. I'd rather connect to the ACC, as I do with the
IC-7800, where the audio signal is not dependent on the AF volume
Heil Pro-Set K2 Boom Headset (including K2 adapter and AD-1-K cable). Can
be used with either the K2 or K3. Brand new, never opened, still unwrapped,
in the box. $120 including FREE SHIPPING to lower 48.
Mike, W4UM
__
Elecraft mail
Anyone using the K3 and the ICOM SM-20 mic? What desk mic is good to use
with the K3? Anyone try different combinations and reach any conclusions?
Mike, W4UM
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elec
Just curious: is anyone using the KBPF3 (general coverage receive module) in
BOTH main and sub-receivers for diversity reception?
Mike, W4UM
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://ma
I am about to order filters for the K3 and need some final advice. I have
the capability for diversity reception on 160 and 80 and am wondering what
is the best filter pair to use for CW. Price really doesn't enter into the
equation as a pair of matched 5-poles filters are about the same price
I asked this same question back in December and received many response. I
then summarized the responses and posted that summary on this reflector.
Now that it's seven months later, I was wondering if anyone wants to share
any additional experiences. I use diversity reception with two antennas,
I see that the general coverage receiver module can be installed in either
the main or sub-receiver. I was planning to install it on the main board as
I have the widest filter (13MHz) there. But before I do, I wanted to hear
some pros and cons for installing on either board.
Thanks,
Mike, W4U
I just received an email that my K3 kit was shipped on December 23 and will
be delivered on January 2nd. Thanks, Santa! I plan to use the K3 with my
PW-1. Anyone doing this (must be many)? Any special precautions to
connecting the two?
Mike, W4UM
Florida Contest Group
South Florida DX Asso
Thanks for all the many helpful responses. Since many out there might want
to know what they were, I have compiled a consensus of the many replies I
received. I plan on using the K-3 for DXing and contesting (CW, SSB, and
RTTY) and want to use diversity reception with two receive antennas on t
Anyone doing this on 160/80? What filter pairs are you using?
Mike, W4UM
Florida Contest Group
South Florida DX Association
Mid-Florida DX Association
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the l
Hi - I'm new to the list and I want to order all the filters I might need so
I can install them at the same time and not have to open the rig each time.
I operate mainly CW, but also SSB and RTTY. I am primarily a DXer but a
contester secondarily. My main bands are the two extremes: 160 and 6.
15 matches
Mail list logo