Plenty of room and you will luv the K-pod!
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.
Subject: [Elecraft] K-pod question
I'm thinking about purchasing a K-pod. My K3 sits flat on a shelf, on its
four rubber feet without the bail extended. Will I have enough clearance
underneath the K3 to attach the K-pod cable, or does the front end of the K3
need to be raised?
Thanks and 73,
It will fit. My K3s sits flat with the K-Pod connected.
--ae0mm
‐‐‐ Original Message ‐‐‐
On Friday, May 24, 2019 8:18 AM, Tony - KM0O wrote:
> I'm thinking about purchasing a K-pod. My K3 sits flat on a shelf, on its
> four rubber feet without the bail extended. Will I have enough cle
I'm thinking about purchasing a K-pod. My K3 sits flat on a shelf, on its
four rubber feet without the bail extended. Will I have enough clearance
underneath the K3 to attach the K-pod cable, or does the front end of the K3
need to be raised?
Thanks and 73,
Tony KM0O
--
Sent from: http://ele
e the macro.
Fred
From: Elecraft on behalf of Joe Subich, W4TV
Sent: Monday, January 16, 2017 3:20 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K-Pod question
On 1/16/2017 11:44 AM, Dave Fugleberg wrote:
I experimented a bit with the method suggested by Fr
ubich, W4TV
Sent: Monday, January 16, 2017 3:20 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K-Pod question
On 1/16/2017 11:44 AM, Dave Fugleberg wrote:
> I experimented a bit with the method suggested by Fred, using VFO-B
> to 'mark' the next signal up the band, and th
On 1/16/2017 11:44 AM, Dave Fugleberg wrote:
I experimented a bit with the method suggested by Fred, using VFO-B
to 'mark' the next signal up the band, and then using A/B to 'jump'
to it. That works, but of course after each 'jump', VFO-B is at the
frequency of the previous QSO.
The K3 contai
t: Monday, January 16, 2017 9:44 AM
To: Cady, Fred; Elecraft List
Subject: Re: [Elecraft] K-Pod question
I experimented a bit with the method suggested by Fred, using VFO-B to 'mark'
the next signal up the band, and then using A/B to 'jump' to it.
That works, but of course after
gt;
> How about using the KPod to tune VFO B and then have a macro that swaps
> A/B. Or just run SO2V.
>
>
> --
> *From:* Elecraft on behalf of Dave
> Fugleberg
> *Sent:* Sunday, January 15, 2017 7:44 PM
> *To:* Elecraft List
> *S
at swaps
> A/B. Or just run SO2V.
>
>
> --
> *From:* Elecraft on behalf of Dave
> Fugleberg
> *Sent:* Sunday, January 15, 2017 7:44 PM
> *To:* Elecraft List
> *Subject:* [Elecraft] K-Pod question
>
> When the K-Pod was first introduced,
How about using the KPod to tune VFO B and then have a macro that swaps A/B.
Or just run SO2V.
From: Elecraft on behalf of Dave Fugleberg
Sent: Sunday, January 15, 2017 7:44 PM
To: Elecraft List
Subject: [Elecraft] K-Pod question
When the K-Pod was first
When the K-Pod was first introduced, there was some indication that a
future enhancement would allow it to control the P3 - specifically, to
adjust the markers and 'tap to QSY'.
Is this feature available yet, or imminent?
I discovered that the P3 is pretty useful for unassisted search and pounce
Sorry, mine is the latest “Beta" firmware, MCU/FPF/DSP = 5.54/1.26/2.88, but
with no such problem.
73 de JH3SIF, Keith
> 2016/12/13 9:05、Ed Muns のメール:
>
> 5.50/1.25/2.87 is the latest firmware release. 5.54/1.26/2.88 is Beta
> firmware. That's the issue.
>
> 73,
> Ed W0YK
> On Dec 12, 2016
For those who do not want to load beta firmware, you will have to
tolerate the problem until 5.54 (or later) is moved to production status.
For those who are cautious about beta firmware, if you want the
function, go ahead and download it (follow the Beta Firmware
Installation instructions), a
5.50/1.25/2.87 is the latest firmware release. 5.54/1.26/2.88 is Beta
firmware. That's the issue.
73,
Ed W0YK
On Dec 12, 2016 3:48 AM, Keith Onishi wrote:
>
> My K-Pod with the latest firmware release does not show such symptom. So D4
> is always OFF unless sending command to set D4 on.
> MCU
My K-Pod with the latest firmware release does not show such symptom. So D4 is
always OFF unless sending command to set D4 on.
MCU/FPF/DSP is 5.54/1.26/2.88.
73 de JH3SIF, Keith
> 2016/12/12 19:15、Ed K1EP のメール:
>
> My D4 is always on too, as I have upgraded to the latest release. Although
> I
My D4 is always on too, as I have upgraded to the latest release. Although
I have had my KPod for a while, I just started using mine regularly. I
thought there were a couple of macros that didn't work right, but I
attributed that to my lack of macro experience on the K3. I will take a
closer look
Hopefully, someone from Elecraft will address this question soon, but
meanwhile here is what I've discovered.
I have two K-Pods, each with firmware 1.02. When Mike contacted me off-list
about this "D4 always on" question, I replied no, D4 should not be on. It
has never been on in my units.
Then
Good afternoon, I just connected the K-pod to my K3 for the first time after
updating the firmware to the latest. I noticed that D4 is always on just
wondering if this is normal?
Mike
VE3WDM
__
Elecraft mailing list
Home: http://mailma
Paul,
I have my pod set up to make the exact selection you want on KPod
button F8 Hold.
In the K3 Utility, for Macro 8, I use SWH47;
Good Luck
73
Tom
HP1XT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraf
Engineer: "If it ain't broke I haven't messed with it enough yet."
Alan N1AL
On 04/21/2016 11:22 AM, Clay Autery wrote:
Yup... that's what I'd do...
__
Clay Autery, KG5LKV
MONTAC Enterprises
(318) 518-1389
On 4/21/2016 10:35 AM, Terry Schieler wrote:
Yes, I too was di
Guess it's time to warm-up the Hakko FR-300 desoldering tool. ;)
Jim Finan
AB4AC
Sent from my BlackBerry 10 smartphone.
Original Message
From: Clay Autery
Sent: Thursday, April 21, 2016 2:23 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K-Pod Question
Yup... that's w
Yup... that's what I'd do...
__
Clay Autery, KG5LKV
MONTAC Enterprises
(318) 518-1389
On 4/21/2016 10:35 AM, Terry Schieler wrote:
> Yes, I too was disappointed to learn that the K-Pod will not be available as
> a kit. Some of you who are similarly disappointed might consid
do me. ;o)
73, Terry W0FM
-Original Message-
From: Eric Swartz - WA6HHQ, Elecraft [mailto:e...@elecraft.com]
Sent: Wednesday, April 20, 2016 4:08 PM
To: Jim Finan; Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K-Pod Question
Its assembled only. There is just one pcb inside.
73
ked here before, I guess I missed it.
I assumed it is, but...
Jim Finan
AB4AC
Sent from my BlackBerry 10 smartphone.
Original Message
From: Jim Finan
Sent: Wednesday, April 20, 2016 11:59 AM
To: Elecraft@mailman.qth.net
Subject: [Elecraft]
@mailman.qth.net
Subject: Re: [Elecraft] K-Pod Question
I guess my question didn't make it.
Question is:
Is the K-Pod a kit?
Can't seem to find any reference to that on the product sheet or website. If
it's been asked here before, I guess I missed it.
I assumed it is, but...
Jim Finan
AB
t: Wednesday, April 20, 2016 10:31 AM
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K-Pod Question
I guess my question didn't make it.
Question is:
Is the K-Pod a kit?
Can't seem to find any reference to that on the product sheet or website. If
it's been asked here befo
one.
Original Message
From: Jim Finan
Sent: Wednesday, April 20, 2016 11:59 AM
To: Elecraft@mailman.qth.net
Subject: [Elecraft] K-Pod Question
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: htt
29 matches
Mail list logo