Hi all
Thanks for the replies,
The filter is a ETS Lindgren Filter N6003 installed on the EMC Chamber wall.
The filter is defined as a 4 line 230/400V 32A <450Hz filter.
When used for DEF STAN EMC measurements and loaded by the 4 of 10uF prior to
the 5uH LISNs it appears to be OK,
however when
Hi members
Can anyone offer some advice.
Have issues with EMC Chamber RF Filter 3 phase.
Using 115V 400Hz single phase supply from a static convertor, filter looks like
it is saturating.
Ambient levels failing between 6kHz to 150kHz.
Voltage of phase at static convertor 115.8Vrms but at EUT on be
Hi All
Looking to replace a 94455-1 Bicon Antenna, does anyone know of a preferred
replacement?
Regards
Andy
Andrew Price
Integrated Sensing & Protection (ISP)
Prinicpal Environmental Engineer (EMC)
Leonardo UK
Sigma House,
Thanks to all that replied.
The information will help decide whether to invest in a replacement active rod
antenna or fin a better amplifier with a better noise figure.
Regards
Andy
Andrew Price
Land & Naval Defence Electronics Division
Prinicpal Environmen
Thanks to those that replied.
I will try what you suggest
Regards
Andy
Andrew Price
Land & Naval Defence Electronics Division
Prinicpal Environmental Engineer (EMC)
Leonardo MW Ltd
Sigma House, Christopher Martin Rd, Basildon SS14
Hi All
Can anyone tell me the ideal value of the load resistor used for verifying the
current in CE101 of MIL-STD-461G.
Regards
Andy
Andrew Price
Land & Naval Defence Electronics Division
Prinicpal Environmental Engineer (EMC)
Leonardo MW Ltd
Hi all,
Is there anyone who has done an ambient noise floor analysis of 41" rod
antennas to determine those with the best performance.
This question comes as a result of the changes to DEF STAN 59-411 Part 3 Issue
3 where DRE03.B is being incorporated into DRE01.B and the limit over the
frequen
Hi all,
Can anyone help?
Looking for technical data on a 95055-1 magnetic Loop.
Regards
Andy
Andrew Price
Land & Naval Defence Electronics Division
Prinicpal Environmental Engineer (EMC)
Leonardo MW Ltd
Sigma House, Christopher Mar
Hi all.
Can anyone help with this query?
Doing a CE106 test, have had to insert 60dB attenuation (40dB + 20dB) in the
antenna output to help prevent the receiver input overloading.
These values incorporated into the measurement software.
Also have had to include a Hi Pass Filter 780MHz to 3000MHz
Thanks everyone for the replies.
I will pass this information onto the person who raised this query.
>From the information I was provided the LED Spots issue a broadband noise seen
>as rise in the ambient noise floor over the frequency range 30MHz to 180MHz,
>there is some minor noise between 18
Hi all.
Has anyone had experience with using LED Spot lamps in EMC Chambers?
What types/manufacturers would be recommended?
Would appreciate help in trying to solve someone's problems with noise during
radiated emissions.
Test Facility has just had all their chambers converted to LED Spots and t
Hi all,
I have used various versions of Emission Software including HP, Emtest,
EMCHire, Labview, Emiscan, Qinetiq own software, and R&S EMC32.
Of these if you use R&S EMI receivers then the EMC32 is probably the best. If
you have other types of receivers than you should use the best for that
r
Thanks all for the replies.
It seems that there is some divided opinion.
Some of the test houses I have spoken to state that they definitely ground
their chambers via ground spikes. This is to remove low frequency noise that
causes issues with the low frequency emc tests that are required in m
Hi All
Which is the best to use?
Ground each EMC chamber via an earth spike or back to the transformer of the
supply to the building?
Which is best practice?
Regards
Andy
Andrew Price
Land & Naval Defence Electronics Division
Prinicpal Environmental Engineer
Hi all.
I hope one of the RF engineers can help with this.
When calculating ERP you use the Tx power either in dBW or W and the antenna
gain in dBi.
So when you have pulse modulation, example 9.3GHz, 38.5dBW (7676.89W) ERP at a
duty cycle of 13%, do you calculate the modulated power level by u
Thanks everyone for your help.
Regards
Andy
Andrew Price
Land & Naval Defence Electronics Division
Prinicpal Environmental Engineer (EMC)
Leonardo MW Ltd
Sigma House, Christopher Martin Rd, Basildon SS14 3EL, UK
Tel
Hi all,
Can a statement that a product is compliant with the EMC Directive 2004/108/EC
or 2014/30/EU in the support documentation be regarded as proof of conformity
or does there have to be a Declaration of Conformity which states compliance
with the Directive via appropriate standards???
Also
Ken
There is no requirement that is flat but there are a few that require such a
high level 1A, 1.7A, 3.98A over the range 2MHz to 30MHz.
Regards
Andy
Andrew Price
Land & Naval Defence Electronics Division
Prinicpal Environmental Engineer (EMC)
Rich
AS far as I am aware there is only one Bulk Current Injection Probe available
for doing high level injection.
It was origonally designed by a Mr Dave Herke at Qinetiq and sold through
Schaffner Chase, later Teseq.
The probe in question is a CIP-9136A. These are made to order.
There are hex
Hi there Group
For some reason it appears that I am not getting any postings from the forum?
Does anyone know why this as occurred?
Regards
Andy
Andrew Price
Land & Naval Defence Electronics Division
Prinicpal Environmental Engineer (EMC)
Leona
Hi All
Anyone know how we can purchase the following Australian Defence Standards:
DEF (AUST) 5681
DEF (AUST)5168 Issue 2
AS/NZS 60529-2004
Need these urgently.
Regards
Andy
Andrew Price
Land & Naval Defence Electronics Division
Prinicpal Environmental Engin
Hi All
Thanks for all your help.
I had a reply from R&S which stated that by changing the units in the
Transducer Correction Table to dBuA/m and then entering the Loop Antenna Values
(dBS/m) into the table the software will automatically correct the result when
the measurement is carried out.
Hi All
I need some help in obtaining the correct result.
The customer has requested an extended magnetic field emission test over the
range 100kHz to 2MHz with a limit defined in dBpT.
The antenna to be used is an EMCO 6512 which has it correction factors provided
in dBS/m which the emission so
Hi all,
Is this a case of Total Recall Johnny Cabs
Is this going to be a case of Software commands versus human intervention and
who or what gets the higher priority.
Also there is going to be a great deal of electronic packages, all round
cameras, lane sensors, range lasers, Doppler and so
Hi all
Can anyone shed some light on working up the Uncertainty Measurement
Calculations based on UKAS Lab34 for MIL-STD-461 CS115 and CS116.
I need to show the uncertainty values for these tests as follows:
Uncertainty in overall test level = 2.2dB, Uncertainty in time measurement =
1.91%, Unce
Hi All
Thanks for the responses it helps.
As far as I can tell 91888-1 and 91889-1 are identical to 91888-2 and 91889-2
Regards
Andy
Andrew Price
Prinicpal Environmental Engineer (EMC)
Land & Naval Defence Electronics Division
Selex ES Ltd
Sigma House, Christopher Martin Rd, Basildon SS14 3EL
Hi All
Can anyone provide me with the gain figures for Ailtech/Stoddard Horn Antennas
91888-1 and 91889-1.
Thanks
Andy
Andrew Price
Prinicpal Environmental Engineer (EMC)
Land & Naval Defence Electronics Division
Selex ES Ltd
Sigma House, Christopher Martin Rd, Basildon SS14 3EL, UK
* Tel
Hi all,
I know this is a little off topic but does anyone know if Environmental
Equipment Ltd is still in existence, after data on several of their
accelerometers??
Regards
Andy
Andrew P. Price
Principle Environmental Engineer, (EMC Specialist)
SELEX ES, A Finmeccanica Company
Sigma House
Hi all
Does anyone have a pdf copy of the New Zealand/Australian Generic EMC
Standards, for emissions and immunity
Regards
Andy
Andrew P. Price
Principle Environmental Engineer, (EMC Specialist)
SELEX ES, A Finmeccanica Company
Sigma House
Basildon
Essex
SS14 3EL
* Tel EMC LAB : +44 (0)
Hi All
Hope someone can help.
Is there some form of agreement between the EU and Hong Kong on accepting
equipment that has met the EU EMC Directive and is CE Marked or does this
equipment have to be retested and remarked accordingly.
Regards
Andy
Andrew P. Price
Principle Environmental En
Hi all,
Ed is right and so are a lot of the others.
I started off in the Avionics Industry and then moved to the Defence Sector
originally doing post design work and then eventually into systems engineering.
During this time solving problems that were major EMC issues.
Even worked on developmen
Hi all
Can anyone advise?
Have a product that has been tested and is EU compliant, there are only a very
small number of these been sold.
A customer has asked if one of these could be modified to do something extra.
This means the addition of some equipment that is purchased from another
suppl
Hi all
Can anyone advise?
Is there a Harmonised Standard for Microwave Ovens apart from 55014 for
Household Appliances??
Regards
Andy
Andrew P. Price
Principle Environmental Engineer, (EMC Specialist)
SELEX ES, A Finmeccanica Company
Sigma House
Basildon
Essex
SS14 3EL
* Tel EMC LAB : +
Hi All
Can any one provide a data sheet for an IFI EFG-2 Antenna.
Regards
Andy
Andrew P. Price
Principle Environmental Engineer, (EMC Specialist)
SELEX ES, A Finmeccanica Company
Sigma House
Basildon
Essex
SS14 3EL
* Tel EMC LAB : +44 (0)1268 883308
*Mobile : +44 (0)7507 854888
email :
Hi all.
Is there any one out there who may have some data on an old Chase UPA 6190B
antenna?
Regards
Andy
Andrew P. Price
Principle Hardware Engineer, EMC Specialist
SELEX GALILEO, Sensors & Airborne Systems
Christopher Martin Road
Basildon
Essex SS14 3EL
Mail Ref : K160
( Tel D
Thanks everyone for your replies.
Problem now solved.
Regards
Andy
Andrew P. Price
Principle Hardware Engineer, EMC Specialist
SELEX GALILEO, Sensors & Airborne Systems
Christopher Martin Road
Basildon
Essex SS14 3EL
Mail Ref : K160
( Tel Direct : +44 (0)1268 887271
( Tel
Can anyone tell me if & when EN61000-6-3:2007 was listed in the OJ.
Regards
Andy
Andrew P. Price
Principle Hardware Engineer, EMC Specialist
SELEX GALILEO, Sensors & Airborne Systems
Christopher Martin Road
Basildon
Essex SS14 3EL
Mail Ref : K160
( Tel Direct : +44 (0)1268 8
Hi everyone
I am looking for an Antenna 1GHz to 18GHz that can be used for em survey work.
This antenna is required for measureing EM fields inside vehicles as well as
outside. The standard double ridge horn has too much directivity.
I have already identified an antenna to cover the frequency r
Hi All
What was wrong with the old Stoddart/Ailtech Identity?
"EMI/Field Intensity Meter"
Regards
Andy
Andrew P. Price
Principle Hardware Engineer, EMC Specialist
SELEX GALILEO, Sensors & Airborne Systems
Christopher Martin Road
Basildon
Essex SS14 3EL
Mail Ref : K160
( Tel Di
all
Have just checked the BS EN document page for BS EN 55022, the version listed
30-11-2006 which is listed as active is version BS EN 55022:2006 +A1:2007.
This document includes limits for Radiated Emissions above 1GHz in Section 6.2
Tables 8 and 9.
Regards
Andy
Andrew P. Price
Principl
Thanks everyone for your replies.
Regards
Andy
Andrew Price
Principal Development Engineer (EMC Specialist)
BAE SYSTEMS Avionics
A125
Christopher Martin Road
Basildon, Essex
SS14 3EL
tel: +44 (0) 1268 883308
email: andrew.p.pr...@baesystems.com
***
Could you add Dr Nigel Carter to the email listing
email nigel.car...@ntlworld.com
Regards
Andy
Andrew Price
Principal Development Engineer (EMC Specialist)
BAE SYSTEMS Avionics
A125
Christopher Martin Road
Basildon, Essex
SS14 3EL
tel: +44 (0) 1268 883308
email: andrew.p.pr...@baesystems.c
Could you please add Dr Nigel Carter
nigel.ca...@ntlworld.com
to the emc_pstc mailing list
Regards
Andy
Andrew Price
Principal Development Engineer (EMC Specialist)
BAE SYSTEMS Avionics
A125
Christopher Martin Road
Basildon, Essex
SS14 3EL
tel: +44 (0) 1268 883308
email: andrew.p.pr...@bae
Thanks everyone for the help provided.
Regards
Andy
Andrew Price
Principal Development Engineer (EMC Specialist)
BAE SYSTEMS Avionics
A125
Christopher Martin Road
Basildon, Essex
SS14 3EL
tel: +44 (0) 1268 883308
email: andrew.p.pr...@baesystems.com
***
Help needed.
Has anyone carried out or know of anywhere that can carryout SAR testing for
a bluetooth transmitter with a power 100mW to 500mW.
Regards
Andy
Andrew Price
Principal Development Engineer (EMC Specialist)
BAE SYSTEMS Avionics
A125
Christopher Martin Road
Basildon, Essex
SS14 3EL
t
45 matches
Mail list logo