OSP2200 - that really is old school.
Same with pre FANUC - 5 controls - single axis LED number position readouts.
I remember making paper tapes on a teletype because I hated standing in front
of a Bandit console typing in; Xxx. (enter) Yxx. (enter) Ixx.
(enter) Jxx. (enter) Fxx.
> Date: Sat, 6 Jul 2013 15:14:52 -0700
> From: skullwo...@yahoo.com
> To: emc-users@lists.sourceforge.net
> Subject: Re: [Emc-users] Okuma absolute encoders (Stuart Stevenson)
>
> I have used many OKUMA machines and I think that they made great iron.
>
> Most had OSP5000 or OSP5020 although som
I have used many OKUMA machines and I think that they made great iron.
Most had OSP5000 or OSP5020 although some were OSP7000 or the newer U100 or
some such control.
I see them for sale surplus every so often but I shudder and pass by - why?
Because its a closed hardware software system.
All t
same guy has a nice Clausing:
http://www.ebay.com/itm/CLAUSING-LATHE/300927639837?ssPageName=WDVW&rd=1&ih=020&category=104241&cmd=ViewItem
On Fri, Jul 5, 2013 at 6:45 PM, andy pugh wrote:
> On 5 July 2013 23:38, Kirk Wallace wrote:
>> In case someone forgot to buy this:
>> http://www.ebay.com/it
On 07/06/2013 01:37 PM, Florian Rist wrote:
> Hi,
> I'm looking for a simulation software that allows to simulate 5axis
> material removal, that is at best open source and hast be not expensive.
>
> If this does not exist I'm thinking about writing one. The geometry part
> of it is not so much of
On Saturday 06 July 2013 15:15:19 Gene Heskett did opine:
> On Friday 05 July 2013 10:03:27 sa...@empirescreen.com did opine:
> > I think testers are always welcome.. :)
> >
> > http://imagebin.org/index.php?mode=image&id=263115
> >
> > http://wiki.linuxcnc.org/cgi-bin/wiki.pl?NewRTInstall
>
>
On Sat, Jul 6, 2013 at 7:37 PM, Florian Rist wrote:
> Hi,
> I'm looking for a simulation software that allows to simulate 5axis
> material removal, that is at best open source and hast be not expensive.
>
> If this does not exist I'm thinking about writing one. The geometry part
> of it is not so
Hi,
I'm looking for a simulation software that allows to simulate 5axis
material removal, that is at best open source and hast be not expensive.
If this does not exist I'm thinking about writing one. The geometry part
of it is not so much of a problem (as long as it does not have to be
efficient)
Gregg Eshelman wrote:
> On Fri, 7/5/13, Hubert Bahr wrote:
>
> Subject: Re: [Emc-users] Shizuoka on eBay
> To: emc-users@lists.sourceforge.net
> Date: Friday, July 5, 2013, 10:09 PM
>
> While I don't need to add a new
> project at this time this does peak my
> interest, but it brings up s
Viesturs Lācis wrote:
> It was a matter of good luck for multimeter
> to show this particular wire lead to be ok.
>
>
No, that is bad luck when testing a defective connection shows it to
be good!
> The end result is - a little soldering and problem solved! Machine works!
> Thanks everyone for y
On 07/06/2013 02:19 AM, Gregg Eshelman wrote:
... snip
> While I don't need to add a new
> project at this time this does peak my
> interest, but it brings up some questions. What type
> of capabilities
> can we expect to get by retrofitting one of these older NC
> machines?
... snip
There is also this application that will generate gcode for synchronous belt
sprockets too: gearotic.com
N. Christopher Perry
On Jul 5, 2013, at 10:24, Chris Kelley wrote:
> Gregg,
>
> I've been playing with doing almost exactly what you are talking about.
> I've even cut some proof-of-conce
On Sat, 6 Jul 2013, Stuart Stevenson wrote:
> Date: Sat, 6 Jul 2013 07:14:41 -0500
> From: Stuart Stevenson
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: EMC2-Users-List ,
> Emc2-developers
> Subject: [Emc-users] Okuma absolute encoders
>
> Will the Okuma absolute encoders al
On Sat, 6 Jul 2013, propcoder wrote:
> Date: Sat, 06 Jul 2013 07:36:22 +0300
> From: propcoder
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: emc-users@lists.sourceforge.net
> Subject: Re: [Emc-users] 7i43 firmware for 7i39 card
>
> Peter, would it be possible to make 7I43/7I39 fir
Will the Okuma absolute encoders allow me to use them as incremental
encoders and a home switch?
--
Addressee is the intended audience.
If you are not the addressee then my consent is not given for you to read
this email furthermore it is my wish you would close this without saving or
reading, an
On Fri, 7/5/13, Hubert Bahr wrote:
Subject: Re: [Emc-users] Shizuoka on eBay
To: emc-users@lists.sourceforge.net
Date: Friday, July 5, 2013, 10:09 PM
While I don't need to add a new
project at this time this does peak my
interest, but it brings up some questions. What type
of capabilit
2013/7/5 Kenneth Lerman
>
> Checking that every pin goes where it belongs is necessary, but not
> sufficient. You must also test that no pin goes where it doesn't belong.
> Did you check to see if any pins were shorted to each other?
>
I checked power cable all the possible pairs of any 2 wire l
17 matches
Mail list logo