On 16 August 2017 at 23:05, Eric H. Johnson wrote:
> Odd thing that I have to check, I thought sure that I was using a 200k 7i43,
> but is being recognized as a 400k.
This was a very unusual problem caused by excessive hubris and someone
thinking that they could fix a bug in the 7i43 driver wit
Andy, Sebastian,
Thanks much, is working now. I will not update again until 2.8 is released.
Odd thing that I have to check, I thought sure that I was using a 200k 7i43,
but is being recognized as a 400k.
Done for today, will check tomorrow.
Thanks again,
Eric
On August 16, 2017 4:50:31 PM E
Sebastian,
Ok, thank you.
After playing with it a bit the lockup went away. It just either won't talk to
the parallel port, or tells me I have the wrong board (200k vs. 400k) although
I have one of each
Regards,
Eric
On August 16, 2017 4:50:31 PM EDT, Sebastian Kuzminsky wrote:
>On 08/16/2
On 08/16/2017 02:38 PM, Eric H. Johnson wrote:
Andy,
I am afraid I do not entirely follow. Does that mean that build is available,
or still rebuilding?
I am showing
1:2.8.0-pre1.3305.gde345856d
as both the installed and latest version. It still locks up when I try to use
the hostmot drivers.
Andy,
I am afraid I do not entirely follow. Does that mean that build is available,
or still rebuilding?
I am showing
1:2.8.0-pre1.3305.gde345856d
as both the installed and latest version. It still locks up when I try to use
the hostmot drivers.
Thanks,
Eric
On August 16, 2017 4:15:06 PM EDT
On 16 August 2017 at 21:09, andy pugh wrote:
>>>You want 1:2.8.0~pre1.3305.gde34585
If you want to watch it happening:
http://buildbot.linuxcnc.org/buildbot/waterfall
Your .deb is way over to the right.
--
atp
"A motorcycle is a bicycle with a pandemonium attachment and is
designed for the es
On 16 August 2017 at 20:43, Eric H. Johnson wrote:
> I have a 6d on the end of gde...,
Yes,
>>You want 1:2.8.0~pre1.3305.gde34585
--
atp
"A motorcycle is a bicycle with a pandemonium attachment and is
designed for the especial use of mechanical geniuses, daredevils and
lunatics."
— George F
Andy,
I have a 6d on the end of gde..., but otherwise the same. Still locking up when
using the hostmot drivers.
Sims work, as does parport | stepper-inch.
Thanks,
Eric
On August 16, 2017 3:32:48 PM EDT, andy pugh wrote:
>On 16 August 2017 at 20:17, Eric H. Johnson
>wrote:
>> Andy,
>>
>> Yes
On 16 August 2017 at 20:17, Eric H. Johnson wrote:
> Andy,
>
> Yes, I see 3305, so I am waiting for that to increment, right?
You want 1:2.8.0~pre1.3305.gde34585
(If I am reading things right)
--
atp
"A motorcycle is a bicycle with a pandemonium attachment and is
designed for the especial use o
Andy,
Yes, I see 3305, so I am waiting for that to increment, right?
Thanks,
Eric
On August 16, 2017 2:22:54 PM EDT, andy pugh wrote:
>On 16 August 2017 at 18:48, Eric H. Johnson
>wrote:
>> Sebastian,
>>
>> My sources.list file reads as follows:
>> deb http://buildbot.linuxcnc.org/ precise ma
It might be helpful if folks were more precise in
describing version names.
The git master branch VERSION file is 2.8.0~pre1
as recorded in this file:
https://github.com/LinuxCNC/linuxcnc/blob/master/VERSION
This VERSION is reported to stdout by the axis gui
and appears in the in the window bo
On 16 August 2017 at 18:48, Eric H. Johnson wrote:
> Sebastian,
>
> My sources.list file reads as follows:
> deb http://buildbot.linuxcnc.org/ precise master-rt
> deb-src http://buildbot.linuxcnc.org/ precise master-rt
This is master / 2.8 and that is what you want.
If you look in the Synaptic
Sebastian,
My sources.list file reads as follows:
deb http://buildbot.linuxcnc.org/ precise master-rt
deb-src http://buildbot.linuxcnc.org/ precise master-rt
deb http://linuxcnc.org/ precise base 2.7-rtai
deb-src http://linuxcnc.org/ precise base 2.7-rtai
The sources.list.d folder is empty. Apol
Andy, Sebastian,
I am unfortunately at the shop and can only get Internet through my phone. So I
am running half blind as far as Lcnc doc. Which version do I need to run that
supports gantry homing with opposing motors (added JOINT section to the ini
file).
It is that version I need to get bac
Andy,
I will wait.
Do I then just need to do an ap-get install?
Thanks,
Eric
On August 16, 2017 1:49:47 PM EDT, andy pugh wrote:
>On 16 August 2017 at 18:08, Eric H. Johnson
>wrote:
>
>> Which version introduced opposing motor gantry support? Was that 2.7,
>and because I had 2.7 pre installed
On 16 August 2017 at 18:08, Eric H. Johnson wrote:
> Which version introduced opposing motor gantry support? Was that 2.7, and
> because I had 2.7 pre installed I inadvertently upgraded to 2.8 pre?
It was master / 2.8.
You do need 2.8, your configs won't work with 2.7.
The buildbot is working
On 16 August 2017 at 17:30, Sebastian Kuzminsky wrote:
> That's terrible! What version of linuxcnc were you running? Was this an
> RTAI build?
This is probably my fault.
https://github.com/LinuxCNC/linuxcnc/commit/036bdd6eccc42ac8c878e54dce1343f58454f2f9
I thought that I had time to get some
Sebastian,
Which version introduced opposing motor gantry support? Was that 2.7, and
because I had 2.7 pre installed I inadvertently upgraded to 2.8 pre?
It is an RTAI build as I had the 7i43-small configuration working fine.
I will try what you say, I would just like confirmation that I am usi
On 08/16/2017 09:57 AM, Eric H. Johnson wrote:
All,
I installed linuxcnc 2.8.0-pre to Xubuntu 12.04, and was running for
some time. I seemed to have upgraded something I should not. The sim
configurations worked, but the default 7i43-small just locks up with
no error message. Nothing responds. C
All,
I installed linuxcnc 2.8.0-pre to Xubuntu 12.04, and was running for some time.
I seemed to have upgraded something I should not. The sim configurations
worked, but the default 7i43-small just locks up with no error message. Nothing
responds. Can only power off computer.
I tried apt-get r
Hi
using the machine today i noticed a little odd bug,
this only happens on a machine with random changer and non random does
not see this bug
when you abort a program with a pre called tool, and run press start
again, the machine will see first M6 and do a tool change regardless of
the firs
21 matches
Mail list logo