Ok in this case I'm using slint to do the install with stage3 so those
lines are needed.
--
Jude
"There are four boxes to be used in defense of liberty:
soap, ballot, jury, and ammo.
Please use in that order."
Ed Howdershelt 1940.
On Tue, 21 May 2024, Michael wrote:
> The line to test if
The line to test if a symlink exists to /run/shm/ from /dev/shm is only needed
when you use non-Gentoo live media to install your system.
With the Gentoo installation media, whether you use the minimal CD or the
admincd, such an action is not needed.
On Tuesday, 21 May 2024 17:52:01 BST Jude
I am installing gentoo to a different disk on the machine and the
install-x86_64-minimal disk is not fit for purpose since I cannot get
espeak reading the screen as I go through an installation.
Most things are pointed at /mnt/gentoo on my system when doing commands.
However in lines where proc is
On 2024-05-21, Dale wrote:
>> Here's my udev rules file that defines my network interface names
>> for the machine I'm on at the moment:
>>
>> --/etc/udev/rules.d/70-my-persistent-net.rules---
>> SUBSYSTEM=="net", ACTION=="add",
Grant Edwards wrote:
> On 2024-05-21, Dale wrote:
>
>
>>> If you want consisent network device names (even when you change
>>> hardware), you need to either
>>>
>>> 1. create udev rules that assign device names based on MAC addresses.
>>>
>>> 2. use a network configuration subsystem that
On 2024-05-21, Dale wrote:
>> If you want consisent network device names (even when you change
>> hardware), you need to either
>>
>> 1. create udev rules that assign device names based on MAC addresses.
>>
>> 2. use a network configuration subsystem that assigns device names
>> and
Grant Edwards wrote:
> On 2024-05-21, Dale wrote:
>
>> So they both show up. When I try to start the network, it says:
>>
>> ERROR: Interface enp3s0 does not exist.
> Are you sure the network interface name hasn't changed? What does
> "ifconfig -a" or "ip addr" show?
>
> After booting up, what
On 2024-05-21, Dale wrote:
> So they both show up. When I try to start the network, it says:
>
> ERROR: Interface enp3s0 does not exist.
Are you sure the network interface name hasn't changed? What does
"ifconfig -a" or "ip addr" show?
After booting up, what does "dmesg | grep enp" show?
>
On Tue, 21 May 2024 06:51:51 -0400, Rich Freeman wrote:
> I usually stick e*
> in my networkd config for the device name on single-NIC hosts. If you
> have multiple NICs then I maybe there is a better way to go about it -
> maybe there is a network manager that can use more data from the NIC
>
Dale:
...
> ERROR: Interface enp3s0 does not exist.
> Ensure that you have loaded the correct kernel module for your hardware.
...
Do:
cat /proc/net/dev
Regards,
/Karl Hammar
On Tue, May 21, 2024 at 6:38 AM Dale wrote:
>
> So, I created a new link to slot 4. The network came up. So,
> basically, it changed names as you suggested. I thought the purpose of
> the enp* names was that they are consistent. Adding or removing cards
> wouldn't change the names of cards,
Grant Edwards wrote:
> On 2024-05-20, Dale wrote:
>
> A 3.0 card is supposed to work fine in a 2.0 slot.
>
>> You, or anyone, have any idea why that card would kill my network?
>> I suspect the card itself is fine. It did see the drive. I just
>> need the internet to work since it may be used
12 matches
Mail list logo
