Re: [gentoo-user] kde-4.1 SLOT in kdesvn-portage

the entire kde-4.1 SLOT has been > removed. Can someone confirm? Am I actually dreaming? Anyone know why a > perfectly reasonable set of ebuilds were removed?\ It was moved to the kde-testing overlay. layman -d kdesvn-portage && layman -a kde-testing -- Best regards, Aleksey Kunitskiy

[gentoo-user] Changing primary monitor on dual-monitor X.org setup

Hi Gentoo community, I'm new to dual-monitor setups and I have one question to you: I have Geforce 7950GT graphics card with two independent DVI-I outputs and two monitors connected to each DVI out. I configured X.org to use two screens separate on these two monitors. Question: How can I interch

Re: [gentoo-user] Changing primary monitor on dual-monitor X.org setup

On Wednesday 06 June 2007 19:54, Dan Farrell wrote: > Try switching the LeftOf to RightOf. Is that what you meant? Or did > you want to plug the monitors into each others' plugs? In which case > >Section "Screen" > > Identifier "Screen0" > > Device "Card0" > > Monitor"Monitor

Re: [gentoo-user] Changing primary monitor on dual-monitor X.org setup

On Wednesday 06 June 2007 21:10, Boyd Stephen Smith Jr. wrote: > Or, just switch the Device lines. Each device is a single DVI port (at > least on my NVidia setup). Section "Screen" Identifier "Screen0" Device "Card1" Monitor"Monitor0" DefaultDepth24

Re: [gentoo-user] Changing primary monitor on dual-monitor X.org setup

On Wednesday 06 June 2007 22:40, Florian Philipp wrote: > Am Mittwoch 06 Juni 2007 20:46 schrieb Aleksey Kunitskiy: > > On Wednesday 06 June 2007 21:10, Boyd Stephen Smith Jr. wrote: > > > Or, just switch the Device lines. Each device is a single DVI port (at > > &g

[gentoo-user] Moving linux system to another partition

Hi all, Is it safe to move my linux system by using: #>cp -rp /mnt/old_part /mnt/new_part and approriate changes in grub.conf/fstab on new system location ? -- best regards, Aleksey V. Kunitskiy -- [EMAIL PROTECTED] mailing list

Re: [gentoo-user] Moving linux system to another partition

On Friday 08 June 2007 18:59, Albert Hopkins wrote: > You could also pass, '-x' to cp and rsync or '--one-file-system' to tar. Thanks. I found good howto [1], chapter #7 describes this problem [1] http://www.tldp.org/HOWTO/Hard-Disk-Upgrade/ -- best regards, Aleksey V. Kunitskiy -- [EMAIL PR

[gentoo-user] KDE (X?) artefacts

HI, I have strange KDE(or X11?) artefacts on my desktop. The animation icon near cursor is drawing ugly, in some places I have bad painted corners. What is it ? This doesn't block my work, but maybe I've bad configured KDE/X :) ? In first attachment (icon) there is an icon In second(tooltip) -

Re: [gentoo-user] KDE (X?) artefacts

On Monday 11 June 2007 17:00, Jesus Guerrero wrote: > So, your problem is, most likely, to be caused by the lack of such > extension. Check your xorg.conf, and make sure you have this line on it, > and it is not commented out. > > Load "extmod" > > -- Jesús Guerrero Thanks! This works for

[gentoo-user] M$ Excel document converter

Hi, Is there any command line converters from M$ Excel to any *nix readable format(i.e. for reading in KSpread)? Excel document contains only text and pictures - no formulas thanks -- best regards, Aleksey V. Kunitskiy -- [EMAIL PROTECTED] mailing list

Re: [gentoo-user] M$ Excel document converter

On Wednesday 13 June 2007 12:40, Florian Philipp wrote: > You can open Excel files with KSpread and Openoffice without an external > converter. Then you can save them in open document format. > > But keep in mind that documents produced by Openoffice are not 100% > compatible with Koffice documents

Re: [gentoo-user] M$ Excel document converter

On Wednesday 13 June 2007 13:10, Peter Ruskin wrote: > > OpenOffice reads (and saves) in M$ Excel format As I mentioned above - OO is very big tool for my needs -- best regards, Aleksey V. Kunitskiy -- [EMAIL PROTECTED] mailing list

Re: [gentoo-user] M$ Excel document converter

On Wednesday 13 June 2007 13:13, Abraham Marín Pérez wrote: > Have you checked that document's Excel format? Maybe KSpread can't read > it because of a too new Excel format, try re-saving it in an older one. > > HTH, > Abraham I don't know what version it is - I get it from internet, and I can't o

Re: [gentoo-user] M$ Excel document converter

On Wednesday 13 June 2007 14:02, Bertram Scharpf wrote: > There's a Ruby package `parseexcel' which seems to work as > far as I can test here. > > I'm not a ruby programmer :( -- best regards, Aleksey V. Kunitskiy -- [EMAIL PROTECTED] mailing li

Re: [gentoo-user] M$ Excel document converter

On Wednesday 13 June 2007 15:04, Boyd Stephen Smith Jr. wrote: > I am. > > Here's a script that will dump a worksheet as a csv. Save, chmod a+x, and > invoke like name_of_script name_of_excel_file worksheet_number > csv_file > (e.g. ./convertxls price_list.xls 0 > price_list.csv): > > #! /usr/bin/

[gentoo-user] Listing packages that depend on specified package

Hi, Today I tried to emerge kde-3.5.7 and I had one blocked package: [blocks B ] <=app-crypt/gnupg-2.0.1 (is blocking app-crypt/gnupg-2.0.4) How can I list packages that depend on <=app-crypt/gnupg-2.0.1 ? thanks for any suggestions -- best regards, Aleksey V. Kunitskiy my public GPG/PGP k

Re: [gentoo-user] Listing packages that depend on specified package

On Sunday 17 June 2007 18:46, Bo Ørsted Andresen wrote: > Packages that depend on <=app-crypt/gnupg-2.0.1 aren't the issue. The fact > that you have <=app-crypt/gnupg-2.0.1 installed is the issue. > > # emerge --unmerge -va \<=app-crypt/gnupg-2.0.1 Thanks Now I have another problem: !!! Digest ve

Re: [gentoo-user] Listing packages that depend on specified package

On Sunday 17 June 2007 20:50, Bo Ørsted Andresen wrote: > The manifest in the tree was broken 5 hours ago (cvs is retarded!). It > should be fixed now so if you sync in a couple of hours the fixed manifest > should be on the rsync mirrors by that time... Thanks -- best regards, Aleksey V. Kunit