Thanks :) I'll let you know how it works out later :P
-William
In a message dated 12/22/2003 9:35:02 AM Pacific Standard Time,
[EMAIL PROTECTED] writes:
> William-
>
> Get yourself a piece of dowel about 1/2 x 4" and a rawhide mallet. Place the
> end of the dowel against the ring at a slight a
coli. Plus, the broccoli is really
good for you.
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of
[EMAIL PROTECTED]
Sent: Sunday, December 21, 2003 1:03 PM
To: [EMAIL PROTECTED]
Subject: [Hornlist] Stuck screw rings?
I have a quick question. I was wanting t
, December 21, 2003 7:43 PM
To: The Horn List
Subject: Re: [Hornlist] Stuck screw rings?
At 1:38 PM -0500 12/21/03, [EMAIL PROTECTED] wrote:
>I'm finding it difficult to get it to move that first few thousandths
of an
>inch. I'm going to spray a little more WD40 in there, let it sit, bu
: Sunday, December 21, 2003 7:34 PM
To: [EMAIL PROTECTED]
Subject: Re: [Hornlist] Stuck screw rings?
William,
This is very true, but you only need to move it a few thousands of an
inch
with the belt to get it
started. Then it should come off by hand.
Paul
On second thoughts I can see why they from a mechanical view should be stuck
there. I am taking into account that a valve that drifts downward isn't a good
thing :P
Oh well, thanks for the advice. At least I can clean out the rest.
-William
___
post:
Well the reason why I want to clean out everything is because I can look with
a flashlight and tell that there is some dirt that I want to get rid of, and
well the little ultrasonic cleaner I have isn't big enough to support the
entire horn :P Also, I do wish to be thorough since soap and water
I agree the company made it that way for a reason. Leave well enough alone.
I clean the horn by taking the rotor's out flushing with warm soapy water the
flushing with clean water. If you want let it soak for a while then rinse.
Works well for me.
John Wilber
___
At 1:38 PM -0500 12/21/03, [EMAIL PROTECTED] wrote:
>I'm finding it difficult to get it to move that first few thousandths of an
>inch. I'm going to spray a little more WD40 in there, let it sit, but if it
>doesn't budge after that I wonder if some guy didn't put loc-tite or
>something in
>there
I'm finding it difficult to get it to move that first few thousandths of an
inch. I'm going to spray a little more WD40 in there, let it sit, but if it
doesn't budge after that I wonder if some guy didn't put loc-tite or something in
there
-William
In a message dated 12/21/2003 10:35:02 AM Pac
William,
This is very true, but you only need to move it a few thousands of an inch
with the belt to get it
started. Then it should come off by hand.
Paul
___
post: [EMAIL PROTECTED]
set your options at http://music.memphis.edu/mailman/options/horn/ar
The pliars were in jest only :P
I found a nice sized belt but it's really hard to get a grip on things in
there.
-William
___
post: [EMAIL PROTECTED]
set your options at http://music.memphis.edu/mailman/options/horn/archive%40jab.org
William,
No ,do not resort to wrenches or pliers.
You could use a thin leather belt- about 1/2" wide.
Wrap the belt around the ring, pull it tightly around the ring with your
fingers, and holding it in that position try to unscrew the ring.
Use light pressure and do not force it , but this gives
I knew it :)
I actually sprayed some WD40 in there an hour ago and I can't get them out by
hand. Do they make strap wrenches or anything small enough to use? I
definately don't want to start using pliars.
-William
In a message dated 12/21/2003 10:22:13 AM Pacific Standard Time,
[EMAIL PROTECT
William,
The screw rings on a E.Schmid horn are NOT soldered.
You might want to try some Wd-40 on the rings. Let it sit in the threads
for an hour or so and try removing them by hand again.
Paul navarro
___
post: [EMAIL PROTECTED]
set your options at
Well I can see screw threads near them and no solder anywhere.
-William
In a message dated 12/21/2003 10:14:20 AM Pacific Standard Time,
[EMAIL PROTECTED] writes:
> They are usually soldered in place. You must remove the rotor.
> >I have a quick question. I was wanting to clean out the bottom
They are usually soldered in place. You must remove the rotor.
> I have a quick question. I was wanting to clean out the bottom bearing plates
> on my Schmid, but the bottom screw rings on the valves appear to be stuck.
>
> Does anyone know the best way to get them un-stuck so I can clean out t
I have a quick question. I was wanting to clean out the bottom bearing plates
on my Schmid, but the bottom screw rings on the valves appear to be stuck.
Does anyone know the best way to get them un-stuck so I can clean out the
bottom bearing plates?
-William
__
17 matches
Mail list logo