Hi there,
I have two juniper netscreens one is Firmware 5.0.0r8.1 . Now I have
encountered a problem when setting up a VPN on this one due to firmware
version thus I need to upgrade it.
The question is how do I upgrade this firmware, challenge being that it
is running live services and if the
Are you using both of the firewalls as n active/active or active/passive;
if yes thn you can try upgrading one of them while the other will take
care of your production services.
Regards,
Masood
Hi there,
I have two juniper netscreens one is Firmware 5.0.0r8.1 . Now I have
encountered a
Sorry guys,
The two firewalls are in completely two different networks and in no way
work together. The reason I mentioned the two is because I tried the
same VPN on the other Firewall with a higher firmware and it worked
within minutes of set-up. So i really want to upgrade this firewall.
Sorry guys,
The two firewalls are in completely two different networks and in no way
work together. The reason I mentioned the two is because I tried the
same VPN on the other Firewall with a higher firmware and it worked
within minutes of set-up. So i really want to upgrade this firewall.
PR55687 was fixed a long time ago, unless your running ancient code you
should be fine. It was fixed in 7.3 and later codes.
On Sat, Jul 11, 2009 at 5:22 PM, raymondh (NSP) raymondh@gmail.comwrote:
Hi Simon,
Based on your config, I assumed you do have an AS / MS PIC (only the AS or
MS
George,
It's not possible to preform any kind of hitless upgrade..
The Netscreen must reboot once the new code is loaded. So you must factor in
the time it will take for the firewall to reload in addition to the hit it
will take when the wall comes back online and the traffic starts to flood
I agree. I ran into PR 434162 which was causing my BGP sessions to
constantly reset on my backup RE, breaking ISSU (on T-series,
however). The fix is making it into 9.3R4 and 9.4R3, and I think
9.4R3 is due later this week.
Might be a different issue than you were hitting, but is related to
Hi,
Has anyone come across an M20 which suddenly looses communication and after
coming back online it looks like the chassis has restarted for some reason.
See messages below.
Jul 10 18:38:06 tnp_scb mpc106 machine check caused by error on the
Processor Bus
Jul 10 18:38:09 CHASSISD_SHUTDOWN:
Thanks Guys,
Sure I had planned to upgrade to above 5.2 , are these firmwares
available for download?
So the next question is really about the configs, Once a reboot is done
all the previous setting take in effect, is that so? And for a rollback
the do I just scroll for the image?
Regards
OK, That's why I see BGP session reset on the new Backup RE but not on
the new master because of resync process and we can say this behaviour
is normal. But why the BFD, ISIS sessions was reset on the new master
and affected neighbours state?
Best Regards,
Walaa Abdel Razzak
-Original
From the docs. Based on distributed or the timeout when not, you can have bfd
timeouts during a nsr; for a gres I believe that bfd is not supported and a
session reset is also expected.
When a BFD session is distributed to the Packet Forwarding Engine, BFD packets
continue to be sent during a
You configuration will remain after the upgrade/reboot.
Downgrading is the same process as upgrading as long as you're going from
say 5.2 to 5.0. Just load the 5.0 image and reboot. The 5.0 image is blown
away when you load the newer screenOS.
Good luck,
-Tim Eberhard
On Mon, Jul 13, 2009 at
I have 2 POPs each with a connection to a common upstream. The upstream
is sending me MEDs, but lots of routes have (missing or 0) MEDs and I
want to reset those to a fixed value so I can tweak them later.
So I have an import policy on each BGP session like so:
term setall-meds {
from
Hi Guys,
I have a lab that I am trying to setup, some basics here. I would like to
setup a J-Series to act like a Frame-relay switch. Could anyone direct me to
some configurations? I am using T1 ports here and would like to get some p2p
and p2m configurations. So some configurations would
14 matches
Mail list logo
