> [EMAIL PROTECTED] wrote:
> > Hallo,
> >
> > I have a Twinhan VP-1027 Sat Pro card. But cant get it to work.
> > Is this card supported?
>
> No
>
To Bad. Is work going on to get it supported or should I look around for
another card?
Magnus--- Begin Message ---
> [EMAIL PROTECTED] wrote:
>
Hi Dietmar,
On Monday 02 April 2007 22:03, Dietmar Zlabinger wrote:
> There are a number decoding errors with interrupt the video/audio
> periodically, I am not sure if this is due to my weak signal, some problems
> in vlc or even problems on the encoder side.
Did you extend the buffers in VLC ?
Henrik Beckman skrev:
Hi,
I just realised that I on the first tuner on the card has flawless
reception on all channels right now but tuner two has very bad
reception (as in not usable)
on several channels.
Is this a known hardware limitation and/or bug or have I´ve just
stumbled on something
Hi,
After reading the advice on the mailing list, I managed to get my
Freecom DVB USB stick (rev 3) to work. I downloaded the latest v4l-dvb
sources and built and installed them and it worked flawlessly.
However recently it's been refusing to work all of a sudden. Dmesg
reports
Hallo,
I have a Twinhan VP-1027 Sat Pro card. But cant get it to work.
Is this card supported? And with witch driver?
00:08.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio
Decoder (rev 05)
00:08.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
Decode
Hi Nico,
On 3/30/07, Nico Sabbi <[EMAIL PROTECTED]> wrote:
(..) run
$ ifconfig dvb0_0 ip/mask promisc up
$ route add -net 224.0.0.0/4 dev dvb0_0
you shouldn't need to tamper with the MAC addresses.
Thank you, with your help I finally succeeded.
My idea to hack the destination address was no
Hi,
I just realised that I on the first tuner on the card has flawless reception
on all channels right now but tuner two has very bad reception (as in not
usable)
on several channels.
Is this a known hardware limitation and/or bug or have I´ve just stumbled on
something.
I have the LNA activated
Em Seg, 2007-04-02 às 09:58 -0700, Dwaine Garden escreveu:
> Here is the polling patch from Henry Does this improve the
> responsiveness of the remote.
> Personally, I never had a problem with the default values that I had..
> +if (adap->id == I2C_HW_SAA7134) /* Handled by saa7134-i
Here is the polling patch from Henry Does this improve the responsiveness
of the remote.
Personally, I never had a problem with the default values that I had..
- Forwarded Message
From: Henry Wong <[EMAIL PROTECTED]>
To: Linux and Kernel Video
Sent: Sunday, January 21, 2007 4:1
here is the patch . I changed
-mod_timer(&ir->timer, jiffies+HZ/10);
to
+ mod_timer(&ir->timer, jiffies+HZ/20);
to improve responsiveness. polls twice as often. Not sure where the
change should go though. Has anyone actually got a repeat from this
card, cause for the life of me i
Jon,
Can you post your kernel patch with the fixes.
I'm probably using the one by Dwaine Garden "80th attempt" post.
I would like any improvement in button response.
Thank you.
Nathan.
---
Nathan Faust
-Original Message-
From: Jonathan Isom [m
On Mon, Apr 02, 2007 at 02:44:30PM +0200, alexw wrote:
> This patch enhances the streamdev plugin by adding client time
> synchronization. Time synchronization needs to be enabled on the client side
> under streamdev plugin setup. In such case, time synchronization will occur
> every channel req
Hello
Yeah I have a modified patch that seems more responsive that
detects button presses
through gpio. also the patch I found on the list (80th attempt)
has some duplicate entries
in the key map that i think is causing some of the
problems(specifically presses being miss
detected as othe
Jon,
Having the same card, the best I have done is:
Apply the kernel patch to create an event input device for the ir
sensor.
I'm still seeing some of the issues talked about with the patch:
delayed button presses the most notable one.
I created a udev rule to map /dev/input/event?
Hi,
This patch enhances the streamdev plugin by adding client time
synchronization. Time synchronization needs to be enabled on the client side
under streamdev plugin setup. In such case, time synchronization will occur
every channel request(switch).
Enjoy,
Alexw
---
From: Manu Abraham [EMAIL PROTECTED]
Date: Sun, 01 Apr 2007 16:09:11 +0200
To: [EMAIL PROTECTED]
Subject: Re: [linux-dvb] About TT-3200
[EMAIL PROTECTED] wrote:
Hallo,
I have a TT-3200 card and trying to get it work in Linux (for running with
Myth).
With some search around I found
Hi David,
I studied these documents but I have still no idea of how to decode the ESG BiM
encoded. In your link there are only DVB-H specification and I'm not a
technician of this... Is possible to have anything simpler to understand how to
solve my trouble?
Thank you
Giovanni
-- Ini
17 matches
Mail list logo