> status 00 | signal | snr | ber | unc |
> status 01 | signal | snr | ber | unc |
I'm not familiar enough with the hardware and I don't know if this will help
but this is the same thing I was seeing when I was getting the dvico dual
digital 4
Hi dvb list,
I'm in need of another dual tuner card and am currently debating between
getting another DD4 or getting one of the newer PCIe cards. Can anyone confirm
that the PCIe Dual Express works with linux (negative responses also helpful)?
I would ideally prefer to go the PCIe path but given
> > Can you confirm you need the extra 125kHz offset from the centre frequency
>
> regarding the specs the different offset is needed for that version of
> the firmware.
> I'll implement it within the next 1-2 hours though :-)
>
> Markus
>
Hi Markus,
Is the extra 125kHz offset band specific o
--- System Administrator <[EMAIL PROTECTED]> wrote:
> I am still experiencing problems with
> SBS (UHF channel 36, 585.625MHz) which, as before, could be caused by
> either the set_frequency offset or bad signal quality.
Hi Daniel,
Can you confirm you need the extra 125kHz offset from the centre
> Hi Roger,
Hello again Markus,
> > The firmware I attached is not a complete replacement for the original
> > firmware. It should replace only the 7MHz (xc3028_DTV7_2633.i2c.fw) for
> > Australia. The base firmware (xc3028_init0.i2c.fw) needs to be loaded
> > first.
>
> Did you forget to atta
--- Funkdafied <[EMAIL PROTECTED]> wrote:
> Excellent news on getting it work :) Thanks for your hard work, Roger.
>
> However, as a linux newbie I'm not quite sure how to install it. I've
> got a fresh install of Ubuntu 7.04.. I've retrieved the master v4l-dvb
> branch and downloaded the patch
--- Markus Rechberger <[EMAIL PROTECTED]> wrote:
> Hi,
Hi Markus,
> Regarding the firmward I have a few considerations (which are no big issues)
>
> * the first device reset request is missing in the firmware, which
> means if that firmware will be used with other devices it wouldn't be
> possi
Hi Daniel,
Just a follow up to our previous discussions which I'm CC'ing to the list as I
think it'll be of use to others. You were right in that my original small
firmware file seemed to hang the usb bus with the experimental branch - not
really a good thing since it required a power down reset
Hi Everyone,
Attached is both a firmware file (identical as previously sent for those who
already have it), plus a patch (against the master branch+Mikes bluebird patch)
which will hopefully resolve the problems for Australian Dual Digital 4 users.
The firmware file sends tuning parameters specif
--- Markus Rechberger <[EMAIL PROTECTED]> wrote:
> Hi,
>
> On 5/4/07, [EMAIL PROTECTED] <[EMAIL PROTECTED]> wrote:
> > Just an update for the list.
> >
> > It appears a simple firmware fix isn't quite enough to resolve the tuning
> > problems in Australia. I'm working with a couple of people to
Just an update for the list.
It appears a simple firmware fix isn't quite enough to resolve the tuning
problems in Australia. I'm working with a couple of people to firstly confirm
my working copy of the tree works elsewhere in Australia and, if so, secondly
to try and nail down which modificati
Hi all,
Does anyone have any ideas on how the remote control interfaces with this
board? I'd like to get a driver going but can't see much from the USB snoop
logs other than demodulator, tuner and transport stream data. Does the remote
even go through the USB port? Any pointers appreciated. Is
Finally some promising news for Australian Dual Digital 4 users.
Many, many hours later it turns out to be fairly simple and I don't think we
need to touch anything other than the tuner but I'm sticking with my hacked
code which spews out register values galore until it's confirmed. It would
have
--- Michael Krufky <[EMAIL PROTECTED]> wrote:
> I am quite sure that you are correct. In my xc-bluebird patch, the
> zl10353 is configured with the same settings that work with the xc3028
> inside the em2880 driver. the zl10353 driver itself *is* working for
> other devices in Australia using tu
Hi Mike,
--- Michael Krufky <[EMAIL PROTECTED]> wrote:
> This, however, isn't clear to me: "zl10353 demodulator is disabled (0x0c ->
> &0x50)" ... can you show a usbsnoop log snippet of this behavior?
I may have jumped the gun as looking through the logs again it looks likes it's
enabled again l
Hi all,
A brief update. Firstly I've confirmed my newly created firmware file (pulled
from usbsnoop logs) being sent to the xc3028 is identical to windows.
Secondly, apart from a gate register being written, the ZL10353 should be
consistent as well. Thirdly when I force the tuning data being se
Hi all,
For those interested I live in Australia (Hobart) and I've been working on
getting the driver for this card going here. I figure the more people working
on it the more likely we are to get something going using random luck.
Unfortunately I still can't get it to tune. So far I've noticed
17 matches
Mail list logo
