[RESEND PATCH net-next] r8169: add module param for control of ASPM disable.

provides signficant (200mW) power savings on the platform I tested. I make some modification that let this patch only for RTL8168G and later. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 73 1 file changed, 50 insertions

[PATCH net-next] r8169: add module param for control of ASPM disable

provides signficant (200mW) power savings on the platform I tested. I make some modification that let this patch only for RTL8168G and later. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 73 1 file changed, 50 insertions

[PATCH net] r8169: fix RTL8168EP take too long to complete driver initialization.

Driver check the wrong register bit in rtl_ocp_tx_cond() that keep driver waiting until timeout. Fix this by waiting for the right register bit. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers

[PATCH net v2] 8139too: fix system hang when there is a tx timeout event.

If tx timeout event occur, kernel will call rtl8139_tx_timeout_task() to reset hardware. But in this function, driver does not stop tx and rx function before reset hardware, that will cause system hang. In this patch, add stop tx and rx function before reset hardware. Signed-off-by: Chunhao Lin

[PATCH net v2 2/3] r8169:add checking driver's runtime pm status in rtl8169_get_ethtool_stats()

Not to call rtl8169_update_counters() to dump tally counter when driver is in runtime suspend state. Calling rtl8169_update_counters() in runtime suspend state will produce warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)". Signed-off-by: Chunhao Lin --- drivers/ne

[PATCH net v2 3/3] r8169:fix nic may not work after changing mac address.

patch I add detecting runtime pm status when setting mac address. If driver is in runtime suspend state, it will skip setting mac address, keep the new mac address, and set the new mac address during runtime resume. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 9 - 1

[PATCH net v2 0/3] r8169:fix 3 runtime pm related issues.

v2: use "struct device *d = &tp->pci_dev->dev" instead of "struct pci_dev *pdev = tp->pci_dev" v1: This series of patches fix 3 runtime pm related issues that are listed below. Chunhao Lin (3): r8169:fix kernel log spam when set or get hardware wol setti

[PATCH net v2 1/3] r8169:fix kernel log spam when set or get hardware wol setting.

. That will let driver thinking register flag is not toggled and then prints the warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)" to kernel log. For fixing this issue, add checking driver's pm runtime status in rtl8169_get_wol() and rtl8169_set_wol(). Signed-off-

[PATCH net] 8139too:fix system hang when there is a tx timeout event.

If tx timeout event occur, kernel will call rtl8139_tx_timeout_task() to reset hardware. But in this function, driver does not stop tx and rx function before reset hardware, that will cause system hang. In this patch, add stop tx and rx function before reset hardware. Signed-off-by: Chunhao Lin

[PATCH net 2/3] r8169:add checking driver's runtime pm status in rtl8169_get_ethtool_stats()

Not to call rtl8169_update_counters() to dump tally counter when driver is in runtime suspend state. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 8 +++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net

[PATCH net 0/3] r8169:fix 3 runtime pm related issues.

This series of patches fix 3 runtime pm related issues that are listed below. Chunhao Lin (3): r8169:fix kernel log spam when set or get hardware wol setting. r8169:add checking driver's runtime pm status in rtl8169_get_ethtool_stats() r8169:fix nic may not work after changing th

[PATCH net 1/3] r8169:fix kernel log spam when set or get hardware wol setting.

will let driver thinking register flag is not toggled and then prints the warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)" to kernel log. For fixing this issue, add checking driver's pm runtime status in rtl8169_get_wol() and rtl8169_set_wol(). Signed-off-

[PATCH net 3/3] r8169:fix nic may not work after changing the mac address.

patch I add detecting runtime pm status when setting mac address. If driver is in runtime suspend state, it will skip setting mac address and set the new mac address during runtime resume. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 9 - 1 file changed, 8 insertions

[PATCH net v2] r8169:Remove unnecessary phy reset for pcie nic when setting link spped.

://bugs.launchpad.net/ubuntu/+source/linux/+bug/1547151 Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index dd2cf37..94f08f1 100644 --- a/drivers

[PATCH net] r8169:Remove unnecessary phy reset for pcie nic when setting link spped.

://bugs.launchpad.net/ubuntu/+source/linux/+bug/1547151 Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index dd2cf37..94f08f1 100644 --- a

[PATCH net v2] r8169: Enable RX_MULTI_EN for RTL_GIGA_MAC_VER_41~48

For RTL8168G/RTL8168H/RTL8411B/RTL8107E, enable this flag to eliminate message "AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x0002 address=0x3000 flags=0x0050] in dmesg. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 4 1 file chang

[PATCH net 2/3] r8169:eliminate error message in using ethtool -S when nic is down.

ing driver runtime pm state. If driver is in runtime suspend state, I will skip dump tall counter. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 8 +++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/ne

[PATCH net 1/3] r8169:fix nic sometimes doesn't work after changing the mac address.

tch I add detecting runtime pm state when setting mac address. If driver is in runtime suspend, I will skip setting mac address and set the new mac address during runtime resume. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 10 +- 1 file changed, 9 insertions(

[PATCH net 3/3] r8169: Enable RX_MULTI_EN for RTL_GIGA_MAC_VER_41~48

For RTL8168G/RTL8168H/RTL8411B/RTL8107E, enable this flag to eliminate message "AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x0002 address=0x3000 flags=0x0050] in dmesg. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 4 1 file chang

[PATCH net 0/3] r8169:issues fix.

This series of patches fix 3 issues that are listed below. Chunhao Lin (3): r8169:fix nic sometimes doesn't work after changing the mac address. r8169:eliminate error message in using ethtool -S when nic is down. r8169: Enable RX_MULTI_EN for RTL_GIGA_MAC_VER_41~48 drivers/net/eth

[PATCH net v4] r8169:fix "rtl_counters_cond == 1 (loop: 1000, delay: 10)" log spam.

the warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)" to kernel log. For fixing this issue, 1.add checking driver's pm runtime status in rtl8169_get_stats64(). 2.dump tally counter before going runtime suspend for counter accuracy in runtime suspend. Signed-off-

[PATCH net v3] r8169:fix "rtl_counters_cond == 1 (loop: 1000, delay: 10)" log spam.

sends the warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)" to kernel log. For fixing this issue, 1.add checking driver's pm runtime status in rtl8169_get_stats64(). 2.dump tally counter before going runtime suspend for counter accuracy in runtime suspend. Signed-

[PATCH net v2] r8169:fix "rtl_counters_cond == 1 (loop: 1000, delay: 10)" log spam.

sends the warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)" to kernel log. For fixing this issue, 1.add checking driver's pm runtime status in rtl8169_get_stats64(). 2.dump tally counter before going runtime suspend for counter accuracy in runtime suspend. Signed-off-

[PATCH net] r8169:fix "rtl_counters_cond == 1 (loop: 1000, delay: 10)" log spam.

sends the warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)" to kernel log. I add checking driver's pm runtime status in rtl8169_get_stats64() to fix this issue. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 10 -- 1 file changed, 8 i

[PATCH net-next] r8169:fix system hange problem.

There are typos in setting RTL8168H hardware parameters. If system install another version driver that may cuase system hang. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 14 +++--- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/drivers/net

[PATCH net-next 2/3] r8169:Fix typo in setting RTL8168H PHY PFM mode.

The PHY PFM register is in PHY page 0x0a44 register 0x11, not 0x14. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index

[PATCH net-next 1/3] r8169:Fix typo in setting RTL8168EP and RTL8168H D3cold PFM mode

The register for setting D3code PFM mode is MISC_1, not DLLPR. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index

[PATCH net-next 0/3] Fix some typos in setting hardware parameter

The typos are in setting RTL8168DP, RTL8168EP and RTL8168H hardware parameters. This series of patch fix these typos. Chunhao Lin (3): r8169:Fix typo in setting RTL8168EP and RTL8168H D3cold PFM mode r8169:Fix typo in setting RTL8168H PHY PFM mode. r8169:Correct the way of setting RTL8168DP

[PATCH net-next 3/3] r8169:Correct the way of setting RTL8168DP ephy

The original way is wrong, it always writes ephy reg 0x03. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 17 + 1 file changed, 5 insertions(+), 12 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c

[PATCH net-next 2/2] r8169:Update the way of reading RTL8168H PHY register "rg_saw_cnt"

The vlaue of RTL8168H PHY register "rg_saw_cnt" only valid from bit0 to bit13. When read this register, add bitwise-anding its value with 0x3fff. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/d

[PATCH net-next 0/2] r8169:Update RTL8168H PHY parameters

Fix typo in setting PHY parameter and update the way of reading PHY register "rg_saw_cnt". Chunhao Lin (2): r8169:Fix typo in setting RTL8168H PHY parameter r8169:Update the way of reading RTL8168H PHY register "rg_saw_cnt" drivers/net/ethernet/realtek/r8169.c | 4 ++-

[PATCH net-next 1/2] r8169:Fix typo in setting RTL8168H PHY parameter

In function "rtl8168h_2_hw_phy_config", there is a typo in setting RTL8168H PHY parameter. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethern

[PATCH net-next v2 4/8] r8169:rtl8168dp rev.c pcie ephy setting is the same as rtl8168dp rev.b

Thease two chips should use the same pcie ephy parameters. So only need function rtl_hw_start_8168d_4. Function rtl_hw_start_8168dp is uncessary. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 20 +--- 1 file changed, 1 insertion(+), 19 deletions(-) diff

[PATCH net-next v2 2/8] r8169:update rtl8168e and rtl8168evl jumbo frame patch

RTL8168E and RTL8168EVL do not need to change pcie max read request size when jumbo frame is enabled. So remove setting pcie max read request size from their jumbo frame patch. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 2 -- 1 file changed, 2 deletions(-) diff

[PATCH net-next v2 5/8] r8169:update rtl8168dp pcie ephy parameters to improve power consumption

The following parameter will disable more pcie ephy block (like pcie ephy read/write clock.etc ) to save more power when in aspm+clkreq mode. { 0x10, 0x0004, 0x } Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion

[PATCH net-next v2 3/8] r8169:correct the way of setting rtl8168dp pcie ephy parameters

The original way is wrong, it always sets the ephy reg 0x03. Correct it in this patch. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 15 --- 1 file changed, 4 insertions(+), 11 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net

[PATCH net-next v2 0/8]r8169:update hardware parameter

function rtl_hw_start_8168f_2 to set rtl8168f rev.b pcie ephy parameters. In v2 patch, give more explanation about pcie ephy parameter update. Chunhao Lin (8): r8169:change rtl8168dp jumbo frame patch r8169:update rtl8168e and rtl8168evl jumbo frame patch r8169:correct the way of setting rtl8168dp

[PATCH net-next v2 8/8] r8169:update rtl8168f rev.b pcie ephy parameter

RTL8168F rev.B does not have to set following two ephy parameters. { 0x06, 0x00c0, 0x0020 } { 0x08, 0x0001, 0x0002 } Add function rtl_hw_start_8168f_2 to set RTL8168F rev.B ephy parameters, instead of using function rtl_hw_start_8168f_1. Signed-off-by: Chunhao Lin --- drivers/net/ethernet

[PATCH net-next v2 1/8] r8169:change rtl8168dp jumbo frame patch

RTL8168DP jumbo frame patch is the same as RTL8168C. So, for RTL8168DP, change to use RTL8168C jumbo frame patch. Also reomve uncessary function "r8168dp_hw_jumbo_enable" and "r8168dp_hw_jumbo_disable". Signed-off-by: Chunhao Lin --- drivers/net/ethernet/

[PATCH net-next v2 6/8] r8169:update pcie ephy parameters to decrease the resume time from L0s to L0

L0. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 19 +-- 1 file changed, 13 insertions(+), 6 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index ade7144..483fa40 100644 --- a/drivers/net/ethernet

[PATCH net-next v2 7/8] r8169:update rtl8402 pcie ephy parameter

Remove following unnecessary ephy parameter. { 0x1e, 0, 0x4000 } Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 483fa40

[PATCH net-next 00/11]r8169:update hardware parameter

set rtl8168f rev.b ephy paramerers. Chunhao Lin (11): r8169:change rtl8168dp jumbo frame patch r8169:update rtl8168e and rtl8168evl jumbo frame patch r8169:change the way of setting rtl8168dp ephy parameters. r8169:update rtl8168dp pcie ephy parameter r8169:remove function

[PATCH net-next 04/11] r8169:update rtl8168dp pcie ephy parameter

Add following ephy parameter. This parameter will save more power when in ASPM mode. { 0x10, 0x0004, 0x } Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers

[PATCH net-next 03/11] r8169:change the way of setting rtl8168dp ephy parameters.

The original way is wrong. I correct it in this patch. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 15 --- 1 file changed, 4 insertions(+), 11 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index

[PATCH net-next 02/11] r8169:update rtl8168e and rtl8168evl jumbo frame patch

For RTL8168E and RTL8168EVL, these two chips do not need to change pcie max read request size when jumbo frame is enabled. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net

[PATCH net-next 07/11] r8169:update rtl8168f pcie ephy parameter

rtl8168f may return to PCIe L0 from PCIe L0s low power mode too slow. The following ephy parameters are for this issue. { 0x00, 0x, 0x0008 } { 0x0c, 0x3df0, 0x0200 } Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion

[PATCH net-next 11/11] r8169:update rtl8168f rev.b pcie ephy parameter

RTL8168F rev.B does not have to set following two ephy parameters. { 0x06, 0x00c0, 0x0020 } { 0x08, 0x0001, 0x0002 } Add function rtl_hw_start_8168f_2 to set RTL8168F rev.B ephy parameters, instead of using function rtl_hw_start_8168f_1. Signed-off-by: Chunhao Lin --- drivers/net/ethernet

[PATCH net-next 06/11] r8169:update rtl8168evl pcie ephy parameter

rtl8168evl may return to PCIe L0 from PCIe L0s low power mode too slow. The following ephy parameters are for this issue. { 0x0c, 0x0100, 0x0020 } { 0x10, 0x0004, 0x } Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion

[PATCH net-next 05/11] r8169:remove function rtl_hw_start_8168dp

RTL_GIGA_MAC_VER_31 is RTL8168DP and it use the same ephy parameter as RTL_GIGA_MAC_VER_28. So I use function rtl_hw_start_8168d_4 to set RTL_GIGA_MAC_VER_31 ephy parameter and remove unnecessary function rtl_hw_start_8168dp. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c

[PATCH net-next 08/11] r8169:update rtl8411 pcie ephy parameter

rtl8411 may return to PCIe L0 from PCIe L0s low power mode too slow. The following ephy parameters are for this issue. { 0x00, 0x, 0x0008 } { 0x0c, 0x3df0, 0x0200 } Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 8 +--- 1 file changed, 5 insertions(+), 3

[PATCH net-next 01/11] r8169:change rtl8168dp jumbo frame patch

For RTL8168DP, its jumbo frame patch is the same as RTL8168DP. So use RTL8168C jumbo frame patch instead and reomve function "r8168dp_hw_jumbo_enable" and "r8168dp_hw_jumbo_disable". Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 28 ++--

[PATCH net-next 10/11] r8169:update rtl8402 pcie ephy parameter

Remove following unnecessary ephy parameter. { 0x1e, 0, 0x4000 } Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index ce98d2a

[PATCH net-next 09/11] r8169:update rtl8105e pcie ephy parameter

rtl8105e may return to PCIe L0 from PCIe L0s low power mode too slow. The following ephy parameters are for this issue. { 0x05, 0, 0x2000 } Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net

[PATCH net-next v2] r8169:update rtl8168g pcie ephy parameter

CIe L0 from PCIe L0s low power mode too slow. The following ephy parameter is for above issue. { 0x19, 0x8000, 0x0000 } Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 24 +--- 1 file changed, 21 insertions(+), 3 deletions(-) diff --git a/drivers/n

[PATCH net-next 5/9] r8169:update rtl8168fb ephy parameter

Update rtl8168fb ephy parameter to improve pcie compatibility. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 28 ++-- 1 file changed, 26 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet

[PATCH net-next 1/9] r8169:update rtl8168g ephy parameter

Update rtl8168g ephy parameter to improve pcie compatibility. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 24 +--- 1 file changed, 21 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek

[PATCH net-next 2/9] r8169:update rtl8168gu ephy parameter

Update rtl8168gu ephy parameter to improve pcie compatibility. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 13 + 1 file changed, 9 insertions(+), 4 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index

[PATCH net-next 4/9] r8169:update rtl8411 ephy parameter

Update rtl8411 ephy parameter to improve pcie compatibility. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 8 +--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 9c946df

[PATCH net-next 7/9] r8169:update rtl8168dp ephy parameter

Update rtl8168dp ephy parameter to improve pcie compatibility. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 39 1 file changed, 8 insertions(+), 31 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net

[PATCH net-next 6/9] r8169:update rtl8168e-vl ephy parameter

Update rtl8168e-vl ephy parameter to improve pcie compatibility. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 2ff8b73

[PATCH net-next 9/9] r8169:update rtl8402 ephy parameter

Update rtl8402 ephy parameter to improve pcie compatibility. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 56bcd96

[PATCH net-next 0/9] r8169:update hardware ephy parameter

Update hardware ephy parameter to improve pcie compatibility. These series of patch include the ephy update of following adapters. rtl8168g rtl8168gu rtl8411b rtl8411 rtl8168fb rtl8168e-vl rtl8168dp rtl8105 rtl8402 Chunhao Lin (9): r8169:update rtl8168g ephy parameter r8169:update rtl8168gu

[PATCH net-next 3/9] r8169:update rtl8411b ephy parameter

Update rtl8411b ephy parameter to improve pcie compatibility. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 10aa0b1

[PATCH net-next 8/9] r8169:update rtl8105e ephy parameter

Update rtl8105e ephy parameter to improve pcie compatibility. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 42eda35

[PATCH net-next 1/2] r8169:prevent enable hardware tx/rx too early

For RTL8168G/GU/H/EP and RTL8411B remove enable tx/rx from its own hw_start function. This will prevent enable tx/rx before complete hardware tx/rx setting. Tx/Rx will be enabled in the end of function rtl_hw_start_8168. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 3

[PATCH net-next 2/2] r8169:disable rtl8168ep cmac engine

Cmac engine is the bridge between driver and dash firmware. Other os may not disable cmac when leave. And r8169 did not allocate any resources for cmac engine. Disable it to prevent abnormal system behavior. Signed-off-by: Chunhao Lin --- drivers/net/ethernet/realtek/r8169.c | 30

[PATCH net-next 0/2] r8169:change hardware setting

This patch series contains two hardware setting modification to prevent hardware become abnormal. Chunhao Lin (2): r8169:prevent enable hardware tx/rx too early r8169:disable rtl8168ep cmac engine drivers/net/ethernet/realtek/r8169.c | 33 ++--- 1 file changed