Linus,
Could you apply the following patch, please?
Andrey
----- Forwarded message from Kai Germaschewski <[EMAIL PROTECTED]> -----
Delivered-To: [EMAIL PROTECTED]
Date: Fri, 6 Jul 2001 22:51:02 +0200 (CEST)
From: Kai Germaschewski <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Subject: [PATCH] eepro100 PCI/PM fixes
Hi!
Appened patch against 2.4.7-pre3 fixes a couple of issues in the eepro100
driver. I realize some of the changes may be not appropriate due to
compatibility concerns or whatever.
o call pci_enable_device before accessing resources/irqs.
pci_enable_device needs to be called, because it may change/assign the
IRQ / resources (not yet).
o call pci_disable_device at appropriate places. Not urgently needed but
cleaner anyway.
o pci_set_power_state is provided by include/linux/pci.h even if
CONFIG_PM is not set
o .acpi_pwr was never really used
o don't do the acpi_idle_state thing. Drivers shouldn't need to care about
this level of things. After an open/close cycle, the chip will be placed
in D2. So it's just consistent to do so before the first open as well.
--Kai
diff -urN linux-2.4.7-pre3.1/drivers/net/eepro100.c
linux-2.4.7-pre3.work/drivers/net/eepro100.c
--- linux-2.4.7-pre3.1/drivers/net/eepro100.c Wed Jul 4 12:37:13 2001
+++ linux-2.4.7-pre3.work/drivers/net/eepro100.c Fri Jul 6 22:41:26 2001
@@ -139,16 +139,6 @@
#define RUN_AT(x) (jiffies + (x))
-/* ACPI power states don't universally work (yet) */
-#ifndef CONFIG_PM
-#undef pci_set_power_state
-#define pci_set_power_state null_set_power_state
-static inline int null_set_power_state(struct pci_dev *dev, int state)
-{
- return 0;
-}
-#endif /* CONFIG_PM */
-
#define netdevice_start(dev)
#define netdevice_stop(dev)
#define netif_set_tx_timeout(dev, tf, tm) \
@@ -165,7 +155,7 @@
#endif
-int speedo_debug = 1;
+static int speedo_debug = 1;
/*
Theory of Operation
@@ -281,7 +271,7 @@
*/
-static int speedo_found1(struct pci_dev *pdev, long ioaddr, int fnd_cnt, int
acpi_idle_state);
+static int speedo_found1(struct pci_dev *pdev, long ioaddr, int fnd_cnt);
enum pci_flags_bit {
PCI_USES_IO=1, PCI_USES_MEM=2, PCI_USES_MASTER=4,
@@ -480,7 +470,6 @@
struct speedo_mc_block *mc_setup_head;/* Multicast setup frame list head. */
struct speedo_mc_block *mc_setup_tail;/* Multicast setup frame list tail. */
long in_interrupt; /* Word-aligned
dev->interrupt */
- unsigned char acpi_pwr;
signed char rx_mode; /* Current
PROMISC/ALLMULTI setting. */
unsigned int tx_full:1; /* The Tx queue is full. */
unsigned int full_duplex:1; /* Full-duplex operation
requested. */
@@ -559,17 +548,21 @@
{
unsigned long ioaddr;
int irq;
- int acpi_idle_state = 0, pm;
static int cards_found /* = 0 */;
static int did_version /* = 0 */; /* Already printed version
info. */
if (speedo_debug > 0 && did_version++ == 0)
printk(version);
+ if (pci_enable_device(pdev))
+ goto err_out_none;
+
+ pci_set_master(pdev);
+
if (!request_region(pci_resource_start(pdev, 1),
pci_resource_len(pdev, 1), "eepro100")) {
printk (KERN_ERR "eepro100: cannot reserve I/O ports\n");
- goto err_out_none;
+ goto err_out_disable;
}
if (!request_mem_region(pci_resource_start(pdev, 0),
pci_resource_len(pdev, 0), "eepro100")) {
@@ -596,20 +589,7 @@
pci_resource_start(pdev, 0), irq);
#endif
- /* save power state b4 pci_enable_device overwrites it */
- pm = pci_find_capability(pdev, PCI_CAP_ID_PM);
- if (pm) {
- u16 pwr_command;
- pci_read_config_word(pdev, pm + PCI_PM_CTRL, &pwr_command);
- acpi_idle_state = pwr_command & PCI_PM_CTRL_STATE_MASK;
- }
-
- if (pci_enable_device(pdev))
- goto err_out_free_mmio_region;
-
- pci_set_master(pdev);
-
- if (speedo_found1(pdev, ioaddr, cards_found, acpi_idle_state) == 0)
+ if (speedo_found1(pdev, ioaddr, cards_found) == 0)
cards_found++;
else
goto err_out_iounmap;
@@ -624,12 +604,14 @@
release_mem_region(pci_resource_start(pdev, 0), pci_resource_len(pdev, 0));
err_out_free_pio_region:
release_region(pci_resource_start(pdev, 1), pci_resource_len(pdev, 1));
+err_out_disable:
+ pci_disable_device(pdev);
err_out_none:
return -ENODEV;
}
static int speedo_found1(struct pci_dev *pdev,
- long ioaddr, int card_idx, int acpi_idle_state)
+ long ioaddr, int card_idx)
{
struct net_device *dev;
struct speedo_private *sp;
@@ -795,8 +777,8 @@
inl(ioaddr + SCBPort);
udelay(10);
- /* Return the chip to its original power state. */
- pci_set_power_state(pdev, acpi_idle_state);
+ /* Put chip into power state D2 until we open() it. */
+ pci_set_power_state(pdev, 2);
pci_set_drvdata (pdev, dev);
@@ -805,7 +787,6 @@
sp = dev->priv;
sp->pdev = pdev;
- sp->acpi_pwr = acpi_idle_state;
sp->tx_ring = tx_ring_space;
sp->tx_ring_dma = tx_ring_dma;
sp->lstats = (struct speedo_stats *)(sp->tx_ring + TX_RING_SIZE);
@@ -1920,7 +1900,8 @@
access from the timeout handler.
They are currently serialized only with MDIO access from the
timer routine. 2000/05/09 SAW */
- saved_acpi = pci_set_power_state(sp->pdev, 0);
+ saved_acpi = sp->pdev->current_state;
+ pci_set_power_state(sp->pdev, 0);
t = del_timer_sync(&sp->timer);
data->val_out = mdio_read(ioaddr, data->phy_id & 0x1f, data->reg_num &
0x1f);
if (t)
@@ -1932,7 +1913,8 @@
case SIOCDEVPRIVATE+2: /* for binary compat, remove in 2.5 */
if (!capable(CAP_NET_ADMIN))
return -EPERM;
- saved_acpi = pci_set_power_state(sp->pdev, 0);
+ saved_acpi = sp->pdev->current_state;
+ pci_set_power_state(sp->pdev, 0);
t = del_timer_sync(&sp->timer);
mdio_write(ioaddr, data->phy_id, data->reg_num, data->val_in);
if (t)
@@ -2202,6 +2184,7 @@
pci_free_consistent(pdev, TX_RING_SIZE * sizeof(struct TxFD)
+ sizeof(struct
speedo_stats),
sp->tx_ring, sp->tx_ring_dma);
+ pci_disable_device(pdev);
kfree(dev);
}
----- End forwarded message -----
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
