The Cubieboard4 has 4 USB ports. 3 of them are connected to a GL850G USB hub chip on usb1. The fourth one, the lower port of 2 ports next to the power barrel, is directly connected to usb3.
2 power enable GPIOs are used between the 2 port groups, 1 for each. This raises the possibility of having no power for hub-connected port next to the power barrel, if usb3 is not enabled. Signed-off-by: Chen-Yu Tsai <w...@csie.org> --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 60 +++++++++++++++++++++++++++++ 1 file changed, 60 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index 6484dcf69873..42ddc046213c 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -62,6 +62,30 @@ stdout-path = "serial0:115200n8"; }; + reg_usb3_vbus: usb3-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&usb3_vbus_pin_cubieboard4>; + regulator-name = "usb3-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */ + }; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +/* usb1 is connected to a GL850G USB hub chip, so no need to enable OHCI */ + +&ohci2 { + status = "okay"; }; &pio { @@ -71,6 +95,20 @@ allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; }; + + usb1_vbus_pin_cubieboard4: usb1_vbus_pin@1 { + allwinner,pins = "PH14"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + usb3_vbus_pin_cubieboard4: usb3_vbus_pin@1 { + allwinner,pins = "PH15"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; }; &mmc0 { @@ -92,8 +130,30 @@ status = "okay"; }; +®_usb1_vbus { + pinctrl-0 = <&usb1_vbus_pin_cubieboard4>; + gpio = <&pio 7 14 GPIO_ACTIVE_HIGH>; /* PH14 */ + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; + +&usbphy1 { + phy-supply = <®_usb1_vbus>; + status = "okay"; +}; + +/* + * Unfortunately reg_usb1_vbus also powers one of the ports from usb3's hub. + * One should always make sure both regulators are enabled and working for + * all USB ports to have power. + */ + +&usbphy3 { + phy-supply = <®_usb3_vbus>; + status = "okay"; +}; -- 2.1.4 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.