In message you wrote:
>
> 2.) I added line "ttyS1::askfirst:-/bin/sh" to inittab ... and I get
> "Bummer, can't open /dev/ttyS1" ... which was funny enough to make me blow
> coffee out my nose ... whats this tty normally used for?
It is you who defines the use of the serial ports on your board -
In message <5.1.0.14.2.20030112121009.02d9da10 at pop.prodigy.net> you wrote:
>
> If ash has been built _without_ job control support it will _never_
> complain about it,
> especially it will never print out that "job control turned off".
Absolutely correct.
> If you look at the source code of a
Xilinx is and has been working very closely with MontaVista to port Linux to
Virtex-II Pro. The following peripherals are implemented and are available today
in the linuxppc_2_4_devel tree:
- Uart 16450/16550
- IIC
- TFT LCD display
- touchscreen
- 10/100 Mbit Ethernet
- GPIO
- Sytem ACE CF contro
In message you wrote:
>
> When it says " can't access tty" ... maybe it should say ttyS00 because "
> ttyS00 at 0x0280 is a SMC" on my mpc860 ... I will have to keep digging ;-)
There is no /dev/ttyS00. The correct name is /dev/ttyS0.
Best regards,
Wolfgang Denk
--
Software Engineering: Embe
In message you wrote:
>
> I just managed to create my first ram-disk image. Which seems to work more
> or less ... however my Ethernet doesn't seem to get configured with my ram
> disk image (see out put below) ...
This does NOT depend on the ramdisk image. It is either a problem
with your
>
> Hi,
>
> I am looking at a ramdisk image ... I am curious if anyone could give me a
> tip as to why when my bash starts I have no "job contol" (ctrl-z etc) ... se
> below ...
>
> BusyBox v0.60.5 (2003.01.09-00:51+) Built-in shell (ash)
busybox builtin shell has no job control by default -
Hi,
I downloaded both the ramdisks. I would appreciate, if
you can tell me what should i have as the value for
"root=", in Kernel Command Line. Mine shows as
"Linux/PPC load: console=ttyS0,19200 console=tty1
ip=off root=/dev/part rw".
And also, if i select the baud rate 19200, do i have
to chang
Thanks,
But that's not it ... I just checked that BB_FEATURE_ASH_JOB_CONTROL is
compiled in ... I think problem may be:
When it says " can't access tty" ... maybe it should say ttyS00 because "
ttyS00 at 0x0280 is a SMC" on my mpc860 ... I will have to keep digging ;-)
Jim
-Original Message
Hi,
I am looking at a ramdisk image ... I am curious if anyone could give me a
tip as to why when my bash starts I have no "job contol" (ctrl-z etc) ... se
below ...
BusyBox v0.60.5 (2003.01.09-00:51+) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
sh: can't access tty; j
As well:
1.) If I "cat /proc/net/dev" eth0 and lo are there ...
2.) If I "ipconfig eth0 192.168.34.67" I can ping as well ...
Jim
-Original Message-
From: James Don
Sent: Sunday, January 12, 2003 1:08 PM
To: 'Wolfgang Denk'; James Don
Cc: 'linuxppc-embedded at lists.linuxppc.org'
Subjec
At 11:24 AM 1/12/2003, you wrote:
> > I am looking at a ramdisk image ... I am curious if anyone could give me a
> > tip as to why when my bash starts I have no "job contol" (ctrl-z etc)
> ... se
> > below ...
> >
> > BusyBox v0.60.5 (2003.01.09-00:51+) Built-in shell (ash)
>
>busybox builtin
James,
At 11:19 AM 1/12/2003, you wrote:
>I am looking at a ramdisk image ... I am curious if anyone could give me a
>tip as to why when my bash starts I have no "job contol" (ctrl-z etc) ... se
>below ...
>
>BusyBox v0.60.5 (2003.01.09-00:51+) Built-in shell (ash)
>Enter 'help' for a list of
12 matches
Mail list logo
