Locally anhemitonic.
dt
To get on or off this list see list information at
http://www.cs.dartmouth.edu/~wbc/lute-admin/index.html
From: "Stuart Walsh"
Several very interesting Ukrainian theorbos have been located in Warsaw,
Gdansk and Krakow museums in Poland.
They are now available for your perusal and delectation at
http://www.torban.org/torban3b.html
Enjoy.
Amitiés,
RT
I went to Krakow a couple of years ago and could
Why does M. Neusidler (Intabolatura di Liuto, 1566) uses the symbol 'X' for
the tenth fret but 'XI' for notes that would normally be on the twelfth
fret?
To get on or off this list see list information at
http://www.cs.dartmouth.edu/~wbc/lute-admin/index.html
Deciding whether to boil the horse and then pluck the vulture, or just fish.
dt
To get on or off this list see list information at
http://www.cs.dartmouth.edu/~wbc/lute-admin/index.html
I have one, almost identical to it. It is very small, and it was brought
to the USA from Messina, Italy, after WWII.
ed
At 08:48 PM 1/26/2009 -0500, Wayne Cripps wrote:
>You can see the pictures at
>
>http://www.cs.dartmouth.edu/~wbc/lute/kayla/InstrumentX002.jpg
>http://www.cs.dartmouth.edu/
You can see the pictures at
http://www.cs.dartmouth.edu/~wbc/lute/kayla/InstrumentX002.jpg
http://www.cs.dartmouth.edu/~wbc/lute/kayla/InstrumentX004.jpg
I would say "mandolin" (from 1880 to 1920) ...poor thing!
Wayne
Forwarded message:
> From: kayla clem
> Subject: [LUTE] Is this a Lute
On Mon, Jan 26, 2009, kayla clem said:
> I've attached
this list is maintained by a demon which ignores attachments; if you can
post it elsewhere you then could give us the Url.
> Whatever it is...somebody tried turning it into a guitar.
If it was originally built as a low-tension lute that w
--0-516706954-1233013680=:38257
Content-Type: text/plain; charset=us-ascii
I've attached pictures of an instrument I found that I believe may be a Lute.
Whatever it is...somebody tried turning it into a guitar.
Thanks!
Kayla xoxo
--0-516706954-1233013680=:38257
Content-Type: text/html; char
Oh, it's all challenging. That's the fun. But much of it becomes
less challenging with practice.
One tip I found out on my second lute is that it might be more
tedious to make a bowl with 11 or more ribs, but it's easier to fit
them. My first lute had 9 ribs and it was harder than heck t
On Mon, Jan 26, 2009, Brod Mac said:
>hello, everyone
>
>what would be the most difficult part of building a six course lute.
I think that varys for each of us.
The bowl is certainly one major challenge, getting the ribs to thickness;
bending them to about the right shape without sin
Several very interesting Ukrainian theorbos have been located in Warsaw,
Gdansk and Krakow museums in Poland.
They are now available for your perusal and delectation at
http://www.torban.org/torban3b.html
Enjoy.
Amitiés,
RT
I went to Krakow a couple of years ago and could only find a folk mus
On Mon, Jan 26, 2009, tam...@buckeye-express.com said:
>Does anyone have a good method of planing or smoothing the edges of
>thin ebony strips to go between ribs?
Make a carrier. Useing a thin blade, table saw a groove in a flat scrap
board which is just wide enough to grip the ebony lea
1. I recommend that you not bend the spacer lumber before cutting into
strips. Slice it up into 3mm or so slices (sticks) and then run it through
the Luthiers Friend until thin enough. Don't be afraid of it but do keep a
firm grip on the stick. Also, do not hesitate as you feed it through or you
wi
Does anyone have a good method of planing or smoothing the edges of
thin ebony strips to go between ribs? I've bent wider pieces of ebony
to the right shape and sliced off thin strips with a band saw. As I
cut each piece I could hand plane the cut edge on what was left, but as
a re
Several very interesting Ukrainian theorbos have been located in Warsaw,
Gdansk and Krakow museums in Poland.
They are now available for your perusal and delectation at
http://www.torban.org/torban3b.html
Enjoy.
Amitiés,
RT
To get on or off this list see list information at
http://www.cs.dartm
Just remember to not try to get the ribs to final thickness before
assembly of the body. Final thickness - and note, rib thickness is not
all that important, it will play fine with a paper mache body, I know,
I did it - is actually achieved after the body is glued up through
scraping
Several very interesting Ukrainian theorbos have been located in Warsaw,
Gdansk and Krakow museums in Poland.
They are now available for your perusal and delectation at
http://www.torban.org/torban3b.html
Enjoy.
Amitiés,
RT
To get on or off this list see list information at
http://www.cs.da
If you don't have a thickness sander (the Old Ones didn't either, so
don't worry) simply clamp one end onto your flat bench top, and using a
small plane (I use a low angle one-handed plane), plane to the required
thickness (ie to allow some trimming and shaping on the mould). For
I use a bandsaw to resaw the stock to approximate thickness (about 3.5mm)
and then a thickness sander to take it down to 1.8mm. The biggest mistake an
amateur makes in rib thicknessing is to make the too thin. They bend nicely
but you have left no "meat" on the rib for scraping, sanding and edge
co
For my thicknesses I resawed on the bandsaw, then I tried both the
"Luthier's Friend" sanding device and the Wagner Saf-T-Planer - both on
the drill press. The final thickness probably should be with a cabinet
scraper -
one way to use a planner to thickness the ribs is, to plane a good fa
20 matches
Mail list logo