Hi Stuart,
You got it right off the bat. I removed mtu config, replaced NONE with
0.0.0.1 and removed the dest line. Booted up and voila, a workable WAN IP
address using pppoe passthrough.
It seems like the realtek card may be holding back performance as I'm only
pulling in 800Mbps or perhaps it
I would recommend trying it like my example, there is a race condition when
you list the destination address separately.
--
Sent from a phone, apologies for poor formatting.
On 20 February 2022 16:50:35 Brodey Dover wrote:
You make a very good point about attaching the configuration :-).
You make a very good point about attaching the configuration :-).
inet 0.0.0.0 255.255.255.255 NONE mtu 1500
pppoedev re0 authproto pap
authname 'username' authkey 'password' up
dest 0.0.0.1
!/sbin/route add default -ifp pppoe0 0.0.0.1
That should help.
Thank you,
On Sun, 20
On 2022-02-19, Brodey Dover wrote:
> Hello all,
>
> I've configured hostname.pppoe0 and hostname.re0 as per the pppoe manpage
> for OpenBSD (I'm running 7) and I'm unable to successfully leverage the
> Bell HomeHub 4000's pppoe passthrough. I've verified that passthrough does
> work with my
Hello all,
I've configured hostname.pppoe0 and hostname.re0 as per the pppoe manpage
for OpenBSD (I'm running 7) and I'm unable to successfully leverage the
Bell HomeHub 4000's pppoe passthrough. I've verified that passthrough does
work with my Windows 7 laptop, however, I just can't get
Andrey Korobkov writes:
> Hello,
>
> I've already had the similar (same?) issue with PPPoE on OpenBSD 6.5 and
> 6.6 when I tried to simply use the example from man pppoe(4).
>
> After looking through source code I thought it's like needed
> configuration structs are not fully populated (missed
peterwkc writes:
> Dear All,
>
> I would like to setup my openbsd as router.
> /etc/hostname.fxp0
> up
>
> /etc/hostname.pppoe0
> pppoedev fxp0 authproto pap authname "" authkey "" up
> dest 0.0.0.1
> !/sbin/route add default -ifp pppoe0 0.0.0.1
>
>
> Not able to get a connection. What wrong
Hey,
* /etc/hostname.vlan500
# hostname.vlan500
vnetid 835 parent parent fxp0
up
* /etc/hostname.pppoe0
#hostname.pppoe0
inet 0.0.0.0 255.255.255.255 NONE \
pppoedev vlan500 authproto pap \
authname "" authkey "" up
dest 0.0.0.1
!/sbin/route add default -ifp pppoe0 0.0.0.1
For debuging:
On Thu, Jan 23, 2020 at 05:59:20AM +0800, Peter Wong wrote:
> The hostname.filename should follow vlan or vnetid?
>
> Regards,
> --
> Peter Wong
> 016-396 3326
Hi,
In my router I have 3 vlans configured so far. I seem to have created
the hostname.if arbitrarily
The hostname.filename should follow vlan or vnetid?
Regards,
--
Peter Wong
016-396 3326
On Wed, Jan 22, 2020 at 2:35 PM Peter J. Philipp wrote:
> On Wed, Jan 22, 2020 at 09:49:18AM +0800, Peter Wong wrote:
> > Yes, my ISP operate pppoe with vlan. How to configure
On Wed, Jan 22, 2020 at 09:49:18AM +0800, Peter Wong wrote:
> Yes, my ISP operate pppoe with vlan. How to configure my fxp0 using vlan id
> 500?
>
>
> Regards,
> --
> Peter Wong
> 016-396 3326
Hi Peter Wong,
My PPPoE router uses VLAN id #7 (IEEE 802.1q protocol),
Yes, my ISP operate pppoe with vlan. How to configure my fxp0 using vlan id
500?
Regards,
--
Peter Wong
016-396 3326
On Wed, Jan 22, 2020 at 6:10 AM Joe Cook wrote:
> Hi,
>
> In my experience, PPPoE operates on a VLAN and not directly on an
> interface like fxp0.
On Mon, 20 Jan 2020 22:42:51 -0700, peterwkc wrote:
> /etc/hostname.pppoe0
> pppoedev fxp0 authproto pap authname "" authkey "" up
> dest 0.0.0.1
> !/sbin/route add default -ifp pppoe0 0.0.0.1
>
> Not able to get a connection. What wrong with it?
Try using authproto chap instead of pap and see
Can you provide me with some more information? Perhaps run
dmesg or check /var/log/messages ? You may also want to
reboot your PC and test ping to see where the network error lies.
jrmu
On Mon, Jan 20, 2020 at 10:42:51PM -0700, peterwkc wrote:
> Dear All,
>
> I would like to setup my openbsd
$man pppoe
or
http://man.openbsd.org/pppoe
Dear All,
I would like to setup my openbsd as router.
/etc/hostname.fxp0
up
/etc/hostname.pppoe0
pppoedev fxp0 authproto pap authname "" authkey "" up
dest 0.0.0.1
!/sbin/route add default -ifp pppoe0 0.0.0.1
Not able to get a connection. What wrong with it?
--
Sent from:
16 matches
Mail list logo
