Holger Eitzenberger <[EMAIL PROTECTED]> wrote:
>Holger Eitzenberger <[EMAIL PROTECTED]> writes:
>
>> bonding: ad_tx_machine() 1210: Sent LACPDU on port 1
>> bonding: bond_3ad_rx_indication() 2175: Received LACPDU on port 1
>> bonding: ad_rx_machine() 1123: Rx Machine: Port=1, Last State=6, Curr
Holger Eitzenberger <[EMAIL PROTECTED]> writes:
> bonding: ad_tx_machine() 1210: Sent LACPDU on port 1
> bonding: bond_3ad_rx_indication() 2175: Received LACPDU on port 1
> bonding: ad_rx_machine() 1123: Rx Machine: Port=1, Last State=6, Curr
>State=6
One important point I forgot about in
Jay Vosburgh <[EMAIL PROTECTED]> writes:
> The log you included (with debug turned on) indicates that
> bonding is at least attempting to send LACPDUs, but there are no log
> entries for having received any LACPDUs.
Yes, the log clearly shows that the LACPDUs are sent, at least bonding
thin
Andy Gospodarek <[EMAIL PROTECTED]> writes:
> I get the impression that sky2 has never worked for you. Is that
> correct? There was an skge problem I noticed a while ago where on reset
> the multicast membership list was cleared.
Well, when it comes to bonding: yes, almost :). When I noticed
On Thu, Feb 15, 2007 at 04:31:36PM -0500, Andy Gospodarek wrote:
> On Thu, Feb 15, 2007 at 07:55:42PM +0100, Holger Eitzenberger wrote:
> > Hi Steven,
> >
> > I have problems using sky2 v1.10 with with bonding driver (802.3ad),
> > on 'Marvell 88E8053 PCI-E Gigabit Ethernet Controller'. I have at
On Thu, Feb 15, 2007 at 10:09:40PM +0100, Holger Eitzenberger wrote:
> Jay Vosburgh <[EMAIL PROTECTED]> writes:
>
> > I'm unfamiliar with your particular switch, but usually this
> > kind of problem with bonding 802.3ad is in the switch interaction. The
> > switches I have (Cisco) require tha
On Thu, Feb 15, 2007 at 07:55:42PM +0100, Holger Eitzenberger wrote:
> Hi Steven,
>
> I have problems using sky2 v1.10 with with bonding driver (802.3ad),
> on 'Marvell 88E8053 PCI-E Gigabit Ethernet Controller'. I have attached
> the full lspci output.
>
> My test was to setup a bond of two phy
Jay Vosburgh <[EMAIL PROTECTED]> writes:
> I'm unfamiliar with your particular switch, but usually this
> kind of problem with bonding 802.3ad is in the switch interaction. The
> switches I have (Cisco) require that 802.3ad mode be explicitly enabled
> on whichever ports it is desired on, s
Stephen Hemminger <[EMAIL PROTECTED]> writes:
>> I used both use_carrier=1 (default) as well as miimon=50 without luck.
>
> use_carrier should work (since device reports carrier transistions).
As you can see in the script I used both use_carrier and miimon (in
combinations) without success. In f
Holger Eitzenberger <[EMAIL PROTECTED]> wrote:
>I have tested v1.10 with kernel 2.6.19 and 2.6.16.36 (own backport),
>which despite the bonding problem runs fine. Both, kernel 2.6.19 and
>2.6.16.36 show the same behaviour. The 802.3ad aware switch is a Dell
>PowerConnect 5324. VLAN is not confi
> I used both use_carrier=1 (default) as well as miimon=50 without luck.
use_carrier should work (since device reports carrier transistions).
--
Stephen Hemminger <[EMAIL PROTECTED]>
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED
Hi Steven,
I have problems using sky2 v1.10 with with bonding driver (802.3ad),
on 'Marvell 88E8053 PCI-E Gigabit Ethernet Controller'. I have attached
the full lspci output.
My test was to setup a bond of two physical links (both links same
hardware) and ping 192.168.11.10, which is the address
12 matches
Mail list logo
