Run Xconfigurator, select custom monitor, then 800x600 @60Hz(just off
the bottom of the small selection box. Use down cursor), then 800x600
again on color depth/res' page.. Assuming that works, go back thro the
same, but when you get to the color depths/resolution page, select
higher res'.
Segmentation faults are very often bad memory. Even if windows runs,
doesn't mean that it is fully OK. DOwnload a GOOD memory test program.
There are several around that run under linux, or a dos one, and boot
from a floppy.
Shane
Arno du Toit wrote:
I installed RedHat 7.3 with X
Try setting your driver to XF86_SVGA. This will force it to use X3.?.
Alternatively, just run XF86_SVGA instead of startx.
Shane
Ray Blair wrote:
All:
I installed RH 7.3 on an HP server with a Cirrus 5420 graphics chipset.
I can't get X to start. I tried the generic VGA driver and it
Try
Xconfigurator, custom monitor, and select 800x600 60Hz, then your
required resolution when you get to the colour/resolution page.
TFT's use slower refresh rates than CRT's, so the 60Hz is important.
Shane
Holt, Patrick wrote:
I've got a similar problem with a Toshiba 5105 except I my
Have you tried rejecting the detected monitor, select custom, and
800x600@60Hz (just off the bottom of the opening screen for custom monitor.
Runlevelsstart @ RL3, then 'startx'.
When this works, RL5 should work aswell.
Shane
___
Newbie mailing
Try running mouseconfig, and try different mouse setups. No other
suggestions at present.
Shane
___
Newbie mailing list
[EMAIL PROTECTED]
*** To unsubscribe , or change message options, see:
http://XFree86.Org/mailman/listinfo/newbie
Isn't that lovelyA happy Newbie. Good on ya. Enjoy.
Regards to all, esp' those who help.
___
Newbie mailing list
[EMAIL PROTECTED]
*** To unsubscribe , or change message options, see:
http://XFree86.Org/mailman/listinfo/newbie
It looks to me like you aint got the drivers installed.
opl.tgz
Description: application/compressed
I ALWAYS use Xconfigurator, and start with custom monitor, 800x600 60Hz,
and work up from there.
Shane
Jon Chalk wrote:
Hi all.
I ran XFree86 -configure and copied the resulting XF86Config file to
/etc/X11. The startx command results in a screen containing vertical
coloured
something?
Vic Roberts
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On
Behalf Of Shane Kennedy
Sent: Sunday, June 23, 2002 5:45 AM
To: [EMAIL PROTECTED]
Subject: Re: [Newbie]mouse isssue
I have said this before, so I don't know
I have said this before, so I don't know if it is usefull.
I ALWAYS use Xconfigurator for X config'. If I am having trouble with
video chip/monitor, select 'custom' monitor, NO to standarsd setup,
select 800x600 60 Hz (usually the 1st one OFF the bottom of the
selection window), then select
It probably isn't much help in this case, but I much prefer
Xconfigurator.it gives YOU the option of selecting different
devices/resolutions/speeds, rather than just reading defaults for your
detected hardware.
Shane
Lionel Lecoq wrote:
have you tried 3.3.6?
Lionel
--- Cary Pembleton
Try what I did earlier today. In /usr/X11R6/bin, replace the
softlink X - XFree86 with - XFree86_SVGA. Check that the SVGA server
exists, and install the rpm if it doesn't.
This very simply forces the system to use the 3.3.? server.
Shane
-Original Message-
From: [EMAIL
I had similar messages, and was told to upgrade to X4.2.0
Did you try running Xconfigurator ?. I find that the Xconfig' during
install doesn'rt always work properly.
Shane
David W. Chapman Jr. wrote:
I think I may have posted this question to the wrong mailing list, so
I'm going to post
I am still in trouble with my NFI touchscreen.
Can anyone help...PLEASE !!!
XFree86-4.2
I need the Section InputDevice
Is 'Option LinkSpeed b9600' valid.
Do I need to call the touchscreen with xsetpointer or similar, as in V3
3m have been totally USELESS !
Their redirect for driver goes
I have been having problems like this for nearly 2 years now. The only
difference is that I am using 3.3.?, with RH6.1 - 7.1.
Also CT, mouse (actually a touchscreen) freezes, but rarely, does the
screen freeze. We have a sequence to text, which keeps sequencing.
I am trying to implement
16 matches
Mail list logo