[Nut-upsuser] Belkin USB UPSes

I just bought a pair of Belkin USB UPSes -- F6C1200-UNV and F6C550-AVR -- and installed the latest version of nut under Ubuntu 7.04. I'm using the F6C1200-UNV. My system does see the device; dmesg says [ 82.718428] usb 2-2: new low speed USB device using ohci_hcd and address 2 [ 82.941189] u

Re: [Nut-upsuser] upsd does not strt up

On 5/14/07, Zoltan Farkas <[EMAIL PROTECTED]> wrote: > Here is the truss output: > > # truss ./upsd Can you try this again with "-DDD"? It's hard to match the system calls to source code, and I'm not very familiar with Solaris or truss anymore. I forget, is IPv6 enabled in the NUT ./configure scr

Re: [Nut-upsuser] NUT and MGE Ellipse ASR 1500 under FreeBSD.

> I stick with RS232 and they work fine though. >> >> Unfortunatelly, I have only one serial port on this box, which >> is used as a console now. The only chance to add another serial is >> usb-com adapter. >If you want reliable comms it's probably the only way to do it for now. Another opt

Re: [Nut-upsuser] NUT and MGE Ellipse ASR 1500 under FreeBSD.

On Wednesday 16 May 2007 23:00, Alex Bakhtin wrote: > DO> I have not had much luck with MGE UPSs talking to FreeBSD boxes > using DO> USB. > > Arnaud Quette from MGE helped me to start driver. It's necessary > to specify user, because by default it runs under 'nobody' > privileges. But NUT st

Re: [Nut-upsuser] mge-shut don't reboot ups by default

Hi Olleg, 2007/5/16, Olleg Samoylov <[EMAIL PROTECTED]>: > Hi > > I have Pulsar 1000 (MGE) and mge-shut 2.0.5-3. > > By default mge-shut don;t reboot ups after upsmoc -c fsd, only permanent > powerdown. > > After I add ondelay=30 in config, all nice, ups restarted after 10 sec. > > But according

Re: [Nut-upsuser] NUT and MGE Ellipse ASR 1500 under FreeBSD.

quickly passing by before going on a week of holidays. @Thierry: we never got time to finish together some documentation on the subject, and I can't recall the exact situation. Can make a small summary? We'll check together for the piece of doc when I'm back. 2007/5/16, Alex Bakhtin <[EMAIL PROTE

Re: [Nut-upsuser] newhidups/APC: load always 0?

On Mon, 2007-05-07 at 18:07 +0200, Tom Laermans wrote: > # upsc [EMAIL PROTECTED]|grep load > ups.load: 0.0 > > This UPS has 2 pc's and some minor other gear connected, yet the load > stays at 0.0 when checking with nut. Ahem - apparently the load was connected to the passthrough connectors inste

Re: [Nut-upsuser] NUT and MGE Ellipse ASR 1500 under FreeBSD.

> "DO" == Daniel O'Connor writes: Daniel, >> I have Ellipse ASR 1500 UPS and now I'm trying to monutor it >> with NUT from FreeBSD. It seems that there are some problems with >> this UPS: DO> I have not had much luck with MGE UPSs talking to FreeBSD boxes using DO> USB. Arnaud Que

Re: [Nut-upsuser] NUT and MGE Ellipse ASR 1500 under FreeBSD.

On Wednesday 16 May 2007 19:52, Alex Bakhtin wrote: > I have Ellipse ASR 1500 UPS and now I'm trying to monutor it > with NUT from FreeBSD. It seems that there are some problems with > this UPS: I have not had much luck with MGE UPSs talking to FreeBSD boxes using USB. I stick with RS232

[Nut-upsuser] NUT and MGE Ellipse ASR 1500 under FreeBSD.

Hello, I have Ellipse ASR 1500 UPS and now I'm trying to monutor it with NUT from FreeBSD. It seems that there are some problems with this UPS: === ugen0: MGE UPS SYSTEMS ELLIPSE, rev 1.10/42.41, addr 2 > usbdevs -v Controller /dev/usb0: addr 1: full speed

[Nut-upsuser] mge-shut don't reboot ups by default

Hi I have Pulsar 1000 (MGE) and mge-shut 2.0.5-3. By default mge-shut don;t reboot ups after upsmoc -c fsd, only permanent powerdown. After I add ondelay=30 in config, all nice, ups restarted after 10 sec. But according man mge-shut ondelay measured in tens of seconds and by default equal 3